Schulte Titan 5000 II Series User manual

©2022 Alamo Group Inc.
Titan 5000 Series II
Published 01/22 s/n:R80120001111-R80120015201 inclusive Part No. R801-010C
OPERATOR’S MANUAL
Schulte Industries Ltd.
PO Box 70
Englefeld Saskatchewan
Canada S0K 1N0
Tel. [phone]
Fax. [phone]
Parts Fax. [phone]
Web: www.schulte.ca
REEL TYPE ROCK PICKER
This Operator's Manual is an integral part of the safe operation of this
machine and must be maintained with the unit at all times. READ,
UNDERSTAND, and FOLLOW the Safety and Operation Instructions
contained in this manual before operating the equipment. C01-Cover

To the Owner/Operator/Dealer
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded
operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has
designed this implement to be used with all its safety equipment properly attached to minimize the chance of
accidents.
BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rules
of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration
Form in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on the
Warranty Card and on the Warranty Form that you retain.

DEALER’S PREDELIVERY SERVICE GUIDE
for the SCHULTE Titan 5000 Series II
DETAILS OF ITEMS LISTED BELOW ARE COVERED IN THIS OPERATOR’S MANUAL
____Shipping damage corrected
____Set up machine as outlined in the shipping instructions attached to these instructions.
____Check that all safety decals are in good condition, replace if necessary.
____Check that gearboxes have been filled with oil.
____Check that all grease fittings have been lubricated.
DEALER’S DELIVERY GUIDE
for the SCHULTE Titan 5000 Series II
____Mounting and removal from tractor
____Operation
____Adjustments
____Lubrication
____Maintenance
____Operator’s safety precautions
____User’s responsibility and warranty
____Operator’s manual delivered to owner
____Operator instructed on contents of owner’s manual

TABLE OF CONTENTS
SAFETY SECTION ............................................................................................................... 1-1
General Safety Instructions and Practices.......................................................................................................... 1-2
Operator Safety Instructions and Practices ........................................................................................................1-3
Equipment Operation Safety Instructions and Practices.....................................................................................1-5
Connecting or Disconnecting Implement Safety Instructions and Practices.......................................................1-8
Transporting Safety Instructions and Practices .................................................................................................. 1-9
Maintenance and Service Safety Instructions and Practices ............................................................................ 1-10
Concluding Safety Instructions and Practices................................................................................................... 1-12
Decal Location .................................................................................................................................................. 1-13
Decal Description .............................................................................................................................................. 1-15
FEDERAL LAWS AND REGULATIONS ........................................................................................................... 1-22
INTRODUCTION SECTION.................................................................................................. 2-1
ASSEMBLY SECTION ......................................................................................................... 3-1
TITAN 5000 SERIES II ASSEMBLY FROM CONTAINERIZED RACKING........................................................3-2
DRIVE COUPLER............................................................................................................................................. 3-21
TITAN 5000 ASSEMBLY FROM LOADING...................................................................................................... 3-24
Wheel Installation.............................................................................................................................................. 3-24
HOSE REST ..................................................................................................................................................... 3-24
Hitch Pole..........................................................................................................................................................3-25
Swing Hitch Lock Pin ........................................................................................................................................3-25
Hydraulic Hose Bracket Assembly .................................................................................................................... 3-26
Rock Deflector Assembly ..................................................................................................................................3-26
PRE-DELIVERY CUSTOMER CHECKLIST .....................................................................................................3-27
OPERATION SECTION ........................................................................................................ 4-1
OPERATOR REQUIREMENTS ..........................................................................................................................4-4
ROPS and Seat Belt ........................................................................................................................................... 4-5
Tractor Safety Devices........................................................................................................................................4-5
Tractor Horsepower ............................................................................................................................................ 4-5
Tractor Hydraulics...............................................................................................................................................4-6
Front End Weight ............................................................................................................................................... 4-6
Tire Spacing........................................................................................................................................................ 4-6
GETTING ON AND OFF THE TRACTOR ..........................................................................................................4-6
Boarding the Tractor ...........................................................................................................................................4-6
Dismounting the Tractor..................................................................................................................................... 4-7
STARTING THE TRACTOR ............................................................................................................................... 4-8
Connecting the Rock Picker to the Tractor .........................................................................................................4-9
Connecting Rock Picker Hydraulic Lines to the Tractor.................................................................................... 4-11
PRE-OPERATION INSPECTION AND SERVICE............................................................................................4-12
Tractor Pre-Operation Inspection/Service......................................................................................................... 4-13
Rock Picker Pre-Operation Inspection/Service ................................................................................................. 4-13
DRIVING THE TRACTOR AND ROCK PICKER .............................................................................................. 4-18
Starting the Tractor ........................................................................................................................................... 4-19
Brake and Differential Lock Setting................................................................................................................... 4-19
OPERATING THE TRACTOR AND IMPLEMENT............................................................................................ 4-21
Foreign Debris Hazards .................................................................................................................................... 4-22
Operating the Rock Picker ................................................................................................................................ 4-23
Shutting Down the Implement ........................................................................................................................... 4-25

ROCK PICKER STORAGE............................................................................................................................... 4-27
TRANSPORTING THE TRACTOR AND IMPLEMENT .................................................................................... 4-27
Transporting on Public Roadways .................................................................................................................... 4-29
Hauling the Tractor and Implement................................................................................................................... 4-33
TROUBLESHOOTING GUIDE .........................................................................................................................4-34
MAINTENANCE SECTION................................................................................................... 5-1
DRIVE COUPLER............................................................................................................................................... 5-2
HYDRAULIC MOTOR .........................................................................................................................................5-3
NUTS AND BOLTS .............................................................................................................................................5-5
Bolt Grades and Torque......................................................................................................................................5-5
HUBS AND SPINDLES.......................................................................................................................................5-6
Greasing and Installation ....................................................................................................................................5-6
TIRES .................................................................................................................................................................5-7
Batt Springs ........................................................................................................................................................5-7
Hydraulics ........................................................................................................................................................... 5-7
LUBRICATION .................................................................................................................................................... 5-8
Grease Schedule ................................................................................................................................................5-8
STORAGE .......................................................................................................................................................... 5-9

Safety Section 1-1
© 2022 Alamo Group Inc.
SAFETY SECTION

SAFETY
Titan 5000 Series II 01/22 Safety Section 1-2
© 2022 Alamo Group Inc.
SAFETY
General Safety Instructions and Practices
A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to
the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and
observing certain precautions. The first section of this manual includes a list of Safety Messages that, if
followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety
Messages before assembling, operating or servicing this Implement. This equipment should only be operated
by those persons who have read the manual, who are responsible and trained, and who know how to do so
responsibly.
The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this
manual and on decals which are attached to the equipment. The Safety Alert Symbol means:
“ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word
are intended to warn the owner/operator of impending hazards and the degree of possible injury
faced when operating this equipment.
Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR
VERY SERIOUS INJURY.
Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH
OR SERIOUS INJURY.
Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR
INJURY.
Identifies special instructions or procedures that, if not strictly observed, could result in
damage to, or destruction of the machine, attachments or the environment.
NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.(SG-1)
Practice all usual and customary safe working precautions and above all---remember safety is
up to YOU. Only YOU can prevent serious injury or death from unsafe practices.
READ, UNDERSTAND, and FOLLOW the following Safety Messages. Death or serious
injury may occur unless care is taken to follow the warnings and instructions stated in the
Safety Messages. Always use good common sense to avoid hazards. (SG-2)
Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las
medidas de seguridad. (SG-3)

SAFETY
Titan 5000 Series II 01/22 Safety Section 1-3
© 2022 Alamo Group Inc.
SAFETY
Operator Safety Instructions and Practices
Never operate the Tractor or Implement until you have read and
completely understand this Manual, the Tractor Operator’s Manual, and
each of the Safety Messages found in the Manual or on the Tractor and
Implement. Learn how to stop the tractor engine suddenly in an
emergency. Never allow inexperienced or untrained personnel to operate
the Tractor or Implement without supervision. Make sure the operator
has fully read and understood the manuals prior to operation. (SG-4)
The operator and all support personnel should wear hard hats, safety
shoes, safety glasses, and proper hearing protection at all times for
protection from injury including injury from items that may be thrown by
the equipment. (SG-16)
PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE
PERMANENT HEARING LOSS! Tractors with or without an Implement
attached can often be noisy enough to cause permanent hearing loss.
We recommend that you always wear hearing protection if the noise in
the Operator’s position exceeds 80db. Noise over 85db over an
extended period of time will cause severe hearing loss. Noise over 90db
adjacent to the Operator over an extended period of time will cause
permanent or total hearing loss. NOTE: Hearing loss from loud noise
[from tractors, chain saws, radios, and other such sources close to the
ear] is cumulative over a lifetime without hope of natural recovery. (SG-I7)
Always read carefully and comply fully with the manufacturer’s
instructions when handling oil, solvents, cleansers, and any other
chemical agent. (SG-22)
KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement
and possible serious injury or death. (SG-24)
Never allow children to play on or around Tractor or Implement. Children can slip or fall off
the Equipment and be injured or killed. Inadvertent contact with controls can cause the
Implement to shift or fall crushing themselves or others. (SG-25)

SAFETY
Titan 5000 Series II 01/22 Safety Section 1-4
© 2022 Alamo Group Inc.
SAFETY
DO NOT use drugs or alcohol immediately before or while operating the
Tractor and Implement. Drugs and alcohol will affect an operator’s
alertness and coordination and therefore affect the operator’s ability to
operate the equipment safely. Before operating the Tractor or Implement,
an operator on prescription or over-the-counter medication must consult
a medical professional regarding any side effects of the medication that
would hinder their ability to operate the Equipment safely. NEVER
knowingly allow anyone to operate this equipment when their alertness or
coordination is impaired. Serious injury or death to the operator or others
could result if the operator is under the influence of drugs or alcohol. (SG-27)
Prolonged operation may cause operator boredom and fatigue affecting safe operation.
Take scheduled work breaks to help prevent these potentially impaired operating
conditions. Never operate the Implement and Tractor in a fatigued or bored mental state
which impairs proper and safe operation. (SG-32)
Use extreme caution when getting onto the Implement to perform repairs, maintenance and
when removing accumulated material. Only stand on solid flat surfaces to ensure good
footing. Use a ladder or raised stand to access high spots which cannot be reached from
ground level. Slipping and falling can cause serious injury or death. (SG-33)
Avoid contact with hot surfaces including hydraulic oil tanks, pumps, motors, valves and
hose connections. Relieve hydraulic pressure before performing maintenance or repairs.
Use gloves and eye protection when servicing hot components. Contact with a hot surface
or fluid can cause serious injury from burns or scalding. (SG-34)
DO NOT operate this Implement on a Tractor that is not properly maintained. Should a
mechanical or Tractor control failure occur while operating, immediately shut down the
Tractor and perform repairs before resuming operation. Serious injury and possible death
could occur from not maintaining this Implement and Tractor in good operating condition.
(SG-36)
Do not operate the implement while wearing loose fitting clothing. Entanglement of the
clothing with the rotating elements can result in serious injury or even death. Stay clear of
all rotating elements at all times. (SSP-03)
Be sure you have adequate knowledge of the property you will be working on. Take time to
make yourself aware of any area underwater or underground lines or cables. Contact with
buried lines or cable could result in serious injury or death. (STL-1)
In wet conditions where there is a likelihood of material collecting on the Implement, make
certain that this material is removed before traveling on public roadways. (STL-7)