Scosche 142HUD2 User manual

Register your product onlin e at
www.scosche.com/register
~ SCCJSCIIE ' HUD2 OBDII
''HEADS-UP'' LED DISPLAY
PARTS INCLUDED
(1) HUD2 display unit
(1) Non-slip dash mat
(1) Reflective window film
(1) 080-11 connecting cable
(1) lnstallation/Owner•s manual
FEATURES
• Display unit projects speed,
engine RPMs and status
information onto windshield
for safer viewing while driving
• Multi-color LED display auto-adjusts
brightness
for day or night driving
• User programmable alerts
for
speed, temp erature and voltage
• Works with 2001 and newer
vehicles with
OBD-11 interface*
SPECIFICATIONS
Display size: 3.0 .. (76.2mm)
diagonally measured
Display type:
LED (multicolor)
Operating temperature: -40 - +176F
(-40- +SOC)
Operating voltage: +9 -16VDC
Operating current: 400mA
(@+ 12VDC)
Operating requirement: OBD
II interface
*CAUTION: The OBD-11 port keeps a very small amount of voltage even the with vehicle
turned off. If you plan to store or NOT use your vehicle
for 30 days, unplug the HUD2 to
prevent battery drain.
©2 017 SCOSCHE INDUSTRIES, INC.
Sl- 300HUD2 12/16

1.
2.
3.
4.
5.
6.
-------------------,
I
1 - --=------- -¢f- I II II I II I 11/11/
\
,,,,,, 3 4 5 6 7
2 ---+-- -1 2
0
X1000RPM
-
-
-
-
---
---
\
I
-----
1
-----
1----- 3
_,_ __ _
------
1 (t •; I (-'} .. t.
\- ~ -
\ 4 5 6 7 8
\ \ \ \ \
HUD2
PROJECTED
IMAGE
HUD2 UNIT
(Mount with this edge
facing
dr i ver)
,
I
I
I
I
I
/
I
I
J
LIGHT SENSOR (Do not obstuct) 7. OVER-SPEED ALARM ICON
ENGINE RPM READOUT
8. ALARM ICON
MAIN READOUT (SPEED/TEMPNOLT) 9. OBD-11 DATA INTERFACE INPUT
SETTINGS ICON
10. POWER SWITCH
VOLTAGE ICON
11. SCROLL SELECTOR (Toggle left/right)
WATER TEMPERATURE ICON
12. ENTER BUTTON (Push in)
2

INSTALLING THE HUD2
IMPORTANT! The vehicle must be equipped with an 080-11 16-Pin diagnostics connection
plug to use the HUD2 device. Most 080-11ports are located under the driver
's side of the
dashboar
d. See "080-11 CONNECTION" below for examples of typical 080-11 connectors.
1. Remove the clear protective film on the HUD2 display.
2. Place the non-slip dash
(A) maton the flattest area
of t he dash top, directly in front of the steering wheel.
The position should allow the display to project onto
the lower portion
of the windshield (see right).
--- C
3. Place the unit onto the mat. Make sure the
Scosche logo is facing you
in order for
the disp lay to project cor rectly (B).
REFLECTION FILM INSTALLATION
Due to the rake (angle) of most vehicles, the
HUD2 image may appear "doubled" or distorted.
We recommend using the included re flection
for
all installations. It will provide the best screen
view
in all conditions, day or night. The film is the
user's choice. If the reflected display is clear
and visible without the film, just keep it
handy for future use, or for other vehicles.
1. With a damp cloth, lightly wet the area of
the windshield directly above the display unit.
Peel off the backing from the reflective film
and apply the film
to the windshield (C).
2. Use a dry cloth to wipe off excess moisture
and remove any air bubbles. For best results,
start
in the center of the film and work toward
the edges. Allow the film
to dry completely.
NOTE: If the projected display image is not
aligned with the reflective film area.
reposition the unit &mat on the dash.
OBD-11 CONNECTION
1. U se the included cable
(D) to connect the unit
to your vehicle's OB0-11
interface socket (E).
2. Conceal the 08 0 -1 1
connection cable
around the edge
of
dashboard and behind
vehicle trim as needed.
NOTES:
. -o
"
1. The 080-11 plug may be behind a cover or not in plain view. Consult your
vehicle manual for exact location for your particular vehicle.
2. When servicing your vehicle, the HUD2
080- II cable should be removed during
diagnostic use.
3
E

GETTING STARTED
1. After installation, start engine and poweron HUD2 . NOTE: Leave the power switch in
the ON position and the
HUD2 will be controlled with the vehicle's ignition).
2. The unit will display the current voltage while communicating with the vehicle's E
CU
(Electronics Control Unit)
3.
Wi thin a few secon ds the HUD2 will display the engine RPM and speed (if moving) ifthe
unit has been installed successfully. If display continues
to ONLY show the voltage,
please check whetherthe
HUD2 OBD-11cable is installed cor rectly and try agai n.
NOTE: If unit still does not operate after steps 1-3, then the HUD2 device maynot be
compa tible with yourvehicle. Call Tech support for assistance: 1-800-621-3695 x3.
(
----- -\
-
= /
==
==
==
,-, -,
I-,,-
-·-
,_
HUD2 SETTINGS
\'
...
/,
,,,,,, : .
~ ..
=
-, --, -= -
,_ ,_
--
==
L Ll ....
\1-'H
==
~
J
The information on the HUD2 display comes from the vehicle's ECU ( El ectronics Control
Unit). In some vehicles there
is a slight variance between what is displayed on HUD2
and the vehicle's dash instruments. The Settings Mode allows you to fine-tune the HUD2
display values, to synchronize (or match) the dashboard. If your HUD2 matches after
installation, then there is no need to access various adjustments. For specific Settings
Mode adjustments, refer to "HUD2 SETTINGS OPTIONS"
on pages 6-7.
USING THE HUD2 SCROLL SELECTOR BUTTON
L 111111111 1 1 1111111 11 R L
11111!1!11 11 1111111 1 R L 1
11111111 1
PRESS INWARD TOGGLE UP
TOGGLE DOWN
To enter and navigate HUD2 Settings Mode:
Press the button IN WARD for 5 seconds.
To navigate adjustments:
Toggle the button UP (left), DOWN (right) and press INWARD (enter) to SELECT
or to change next option leve
l.
To change values and options:
To change option values toggle t he button UP (left), DOWN (right). Once you have
the correct value press
the button INWARD to scroll to next option# .
4

MAIN DISPLAY SCROLLING
Press and re lease the setting button to change the
scroll of the main display function between MPH,
voltage and water temp. L :
1111 1 11 11 1111111111 R
~ --, ~
:-,,- I G
.......... ·--'
,--, .... , 0
'
... ,, ...
...........
AUDIBLE WARNING ALARMS
To turn the Audible alarms OFF, press and hold the Settings
toggle switch toward "R"
for 5 seconds and Alarm Icon will
beep and turn OFF To activate alarm, repeat this step and
Alarm icon will illuminate.
L 11 1111111 1 IJII!!IIII R
FACTORY OPTION RESET
•c•- o
1!..1
Press and hold the Settingstoggle switch toward "L"
for 5 seconds and entire HUD2 LED display will turn
on. Repeat this step and options will restore to factory
default values.
L 1 111111111 1 11111111 1 R
(
' ,, .... ,,,,,,,,,,,
,,,,, +
== =
,._, rlrl .r
,..., I J ,..., •. r~
~ ...... --·~ klt
=== ==
-----
-----
0
/
HUD2 AUTO POWER OFF
When the vehicle is turned off, the HUD2 device will sense lower voltage levels and shut
itself off. It may take from 10 seconds to 1 minute to turn OFF.
5