Scosche ITCFDOSAB User manual

ITCFDOSAB
Kit Content
IN-DASH INSTALLATION KIT FOR 2015-UP FORD MUSTANG
SINGLE ZONE MANUAL/ DUAL ZONE AUTOMATIC CLIMATE CONTROLS
ADAS H MOD IFI CAT I ON REOUIREDA-
1. Face Panel w/ UAC (7773)
2. Right Bracket (777 4)
3. Left Bracket (7775)
4. Three Button Switch Trim (777 6)
5. Four Button Switch Trim (7777)
6. Back Cover (7778)
7. PBC Spacer (7779)
8. Pocket(6761)
Tools Required
Pane l Remova l Too l
Screwdriver
Pc,tary Cutting Too l
Filing Too l
~ Extremelyhigh temperatures may
' j' ':NOTICE:
. IJ operation will resume once the unit cools.
=- temporarily affect the display, Normal
INTRODUCTION/ PRELIMINARY
This premium installation kit is for 2015-UP Ford Mustang vehicles with single/dual zone manual climate controls (dash
modification required). Included are all the parts you need to mount your aftermarket car stereo or CD player into you vehicle's
dash. Refer to individual instructions in this manual to remove your vehicle's factory radio and assemble the kit.
CAUTION: DISCONNECT YOUR VEHICLES NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP
PREVENT ELECTRICAL DAMAGE. WE RECOMEND THE USE OF A VOLT/ OHM METER OVER A TEST LIGHTTO CHECK
WIRING. A TEST OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S COMPUTER AND/OR
DIAGNOSTIC SYSTEM. AVOID ALL FACTORY AIRBAG WIRING · AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING
SERIOUS INJURY OR DEATH .
NOTES:
• See your vehicle's instructions for any special tools your installation might requi re.
• Read a ll instructions accompanying your car stereo for proper wiring and mounting instructions
IMPORTANT!
DO NOT RETURN PRODUCT TO THE RETAILER
[s,oP
IF YOU NEED ASSISTANCE OR REPLACEMENT PARTS CALL US TOLL FREE 800-363-4490 x1
HOURS: MON-FRI 8AM-5:30PM (PST) SATURDAY 8AM-2PM (PST)
LIABILITY DISCLAIMER
This instruction booklet is based on carefu lly documented data and research of automobile dash disassembly, wire harness/
codes and information pertaining to installation of this kit ITCFDOSAB. Scosche Industries, I nc. cannot be held responsible for
discrepancies/inconsistencies that may occur due to the automobile manufacturing changes or options, or damage that may occur
in the automobile during the installation of components while using this booklet.
If you have any further questions, call our toll free technical help line at: 1-800-363-4490 x1
©202 1 SCOSCHE INDUSTRIES, IN C.
ITCFD05AB 10/21

INSTALLATION GUIDE RAD/0D/SASSEMBLY
STEP 1 RADIO DISASSEMBLY
Image A: Remove the two (passenger and driver
side) knee panels on the lower console.
Image B: After removing the knee panels, Remove
two exposed screws
STEP 2 RADIO DISASSEMBLY
Image A: Using a panel removal tool, carefully re-
move the tray located below the USB and 12V socket
ports, then remove and reta in two screws exposed .
Image B: Lift and slightly pullback the center
console, but do not remove .
STEP a RADIO DISASSEMBLY
Using a panel removal tool, carefully remove the
air-vent trim surrounding the ver:its, temps, and boost
control gauge; unplug and remove.
STEP 4 RADIO DISASSEMBLY
Unclip and remove the plastic plate located
in-between the USB plug-in and the
cigarette lighter .
©2 021S CO SC HE INDU S TRIE S, IN C.
2
IT C FD 0S AB 10 /2 1

INSTALLATION GUIDE RAD/00/SASSEMB LY
STIP ' RADIO DISASSEMBLY
Remove the four screws securing the OEM panel to
the dash; then unplug and remove the panel (see
image on the right) .
ITIP 6 RADIO DISASSEMBLY
Remove the OEM display and the CD receiver by
unscrewing t he four screws for each component (8
screws total, circled) . Next, unplug all wiring and
remove (see image on the left) .
INSTALLATION GUIDE Dash Modification
CAUTION: Major modification required for double DIN Installation, proceed with caution.
STEP 7 Dash Modification
Carefully cut and remove the highlighted
dashed area on the sub - dash frame to create
space for the double DIN radio .
File down the slight ridge areas highlighted
and noted on the image locate on the ri ght.
NOTE: Only file down necessary amount to
give the UAC a flush fit.
©2 021 SCOSC HE IN DU ST RI ES, IN C.
3
ITCFD0SAB 1 0/21

INSTALLATION GUIDE Panel Preparation
STEP 8 Panel Preparation
Remove fifteen (15) screws and the 12V socket located
behind the OEM climate control'panel and retain for later
installation; then remove the PCB board back cover.
NOTE: The amount of screws may vary with vehicle model.
Retain the 12V socket from the OEM panel and place it on
the aftermarket panel.
STEP 9 Panel Preparation
Remove the seven screws securing the PCB board to the
panel; then remove from panel.
NOTE: The amount of screws may vary with vehicle model.
n•P 1O Panel Preparation
Lift and remove the plastic CD insert slot away from its
general location.
Close-up
STEP 11 Panel Preparation
Lift and remove the drive train/ ignition controls
and rubber pad from the OEM panel and retain for
later install.
NOTE: Remove rubber and plastics blocking pieces
needed in-order to remove the ignition controls
(See image on the right).
© 2021 SCOSCHE INDUSTRIES , INC.
4
ITCFDOSAB 10 / 21

INSTALLATION GUIDE Panel Preparation
NOTE Panel Preparation
PCB: 3 BUTTON + START PCB :4 BUTTON + START
STIP 12 Panel Preparation
Place the three orfour button drive-train/
ignition control trim (777 6/ 7777) into the face
panel (Based on vehicle model type).
NOTE : Image image of panel on right is ba s ed on three button.
STEP 1S Panel Preparation
Place the OEM drive - train/ ignition control buttons
(retained in Step 11) into the trim from Step 12 .
Next, place the three provided PCB spacers indicated
by arrows on top of button controls.
STEP 14 Panel Preparation
Place the rubber pad from the OEM
drive-train controls onto the back of the
buttons being caut i ous not to knock over
the spacers placed on previous step .
NOTE: 4- Button displayed, follow same
procedure for 3- button
STEP 15 Panel Preparation .
Carefully align the circuit board over the rubber
pad, then continue to the next step.
()2 021 SCOS CHE INDU ST RIE S, IN C.
5
3- Button displayed , follow same procedure
for 4- button
IT CFDOSAB 10 /2 1

INSTALLATION GUIDE Panel Preparation
SJJP 16 Panel Preparation
Place the back cover plate over the PCB and secure it
using six screws retained in disassembly.
NOTE: Use the screws attained from the OEM PCB
cover plate.
INSTALLATION GUIDE Radiotnstallation
STEP 17 Radio Installation
Single DIN Only
... "'>. ©
.:, '-:::
~~«>-
.. ' ,,: ,
Attach brackets provided to the pocket (A), "
then secure the rad io to the brac . kets (B) . Lastly,
secure radio assembly into dash cavity (C) and
proceed to the next step .
STEP 18 Radio Installation
Connect and reassemble ev -
erything in reverse order of the
disassembly to complete the
installation .
NOTE: 12V / Cigarette plug is
retained from the OEM panel.
©2021 SCOSC HE INDU STR I ES, IN C.
,,/
Double DIN Only
Attach provided bra c kets to then secure th ea f-
termarket radio (D). Next, s ecure radio assembly
into the dash cavity (E) then proceed to the nex t
step .
Single DIN
6
Single DIN
I TCFD0SAB 10/ 21

STEERING WHEEL WIRING CODES Left Screen (Cont'd )
FIGURE 1A
1. Prepare SWC steering wheel connector harness by using the chart below
2. Connect the harness to the interface module.
3. For Alpine, Clarion, JVC, Panasonic and Sony car stereos, connect the 3.5mm male steering plug into the steering wheel
input jack at the back of the stereo.
4. For Kenwood and newer JVC stereos, connect the BROWN wire from the steering wheel harness to the •Remote in• wire
at the back of the stereo.
I
STEREO BRAND CONFIGURATION CONNECTION TO STEREO
ALIPNE
Cut Green Loop 3.5mm
CLARION Cut Violet Loop
3.5mm
JVC Cut Green & Violet Loop 3. 5mm or Brown (Key1)
KENWOOD Cut Orange & Green Brown ( Key 1)
PANASONIC Cut Orange Brown (Key 1)
PIONEER/ SONY Do Not Cut Loops 3.5mm
OTHER BRANDS Ca ll Tech Support Brown, Gray , Black
FIGURE 11 Alpine Sample
NOTE : Do NOT remove, cut wires (see samples betow)
FIGURE 1C Kenwood Sample
Orange
Green (Cut)
Violet
Orange (Cut)
Green (Cut)
Violet
STEER I NG WHEEL CONTROLS Left Screen (Cont'd )
The Scosche ITCFDOSAB (2015 - UP Ford Mustang) face panel comes with a steering wheel control harness that will retain the vehicles OEM
steering wheel capabilities when equipped. Refer to the HVAC wiring diagram for a connection guide . For further or more detailed understand -
ing of the steering wheel controls,* please refer to your vehicles owner manual for button functionalities .
1. T ra ck, Seek Down
2. Vo lu me Up
3. 1r ack / Seek Up
4. Vo l ume Down
5. Voice Command (JVC/t lp1n e/Pionec1 un, ls w1lh Voice Command Capabd11ies)
6. Mute
7. "hone Hang-UP (BT f4U On l y)
8. Phone Pic k -U P (B T HU On l y)
•Refer to Veh icl e Owner's Manua l for buttons l oca t ed on t he l eft s id e of th e
st eering whee l
©2021 SCOSCHE IN DUSTRIES, INC.
7
..- .......... ...---......---------.
ITCFDOSAB 10 /21

ITCFDOSAB WIRING DIAGRAM LEGEND
FIGURE 2 WIRING DIAGRAM LEGEND
A. Connect to the back of the Push - Start module
B. Connect to aftermarket radio (See WIRING COLOR CODES below)
C. Vehicle Speaker Wires Connector (Color codes below)
* If the vehicle has Shaker Audio then the Shaker interface should be connected to C and L
should be plugged into the other end of the interface .
D. Connect to vehicle factory rad io chass is
E. Steering Wheel Controls (See Page 7 for more details)
F. Connect to the back of the UAC.
G. Reverse video (RCA, Brown)
H. Connect to vehicle harness Behind Screen for both
4.2' and 8' monitors (Attach to Sync box)
I. Audio Aux (RCA, White)
J. AUDIO Aux (RCA, Red)
K. For use with 4.2' monitor connectors only.
L If the vehicle has Shaker Audio then the Shaker interface should be connected to C and L
shou ld be plugged into the other end of the interface .
M. Connect to aftermarket radio (See Color Codes Below)
N. Connect to aftermarket radio's AMP remote (Blue/White)
0. Connect to aftermarket radio's AMP remote (Blue/White)
P. Connect to C (For use with Non Shaker systems On l y)*
Q. Connect the speaker wires from the after market radio to the wires at Q (For use with Non Shaker systems Only)*
WIRING COLOR CODES
White=
White/Black=
Green=
Green/Black=
Black=
Yellow=
Red=
Blue=
Blue/White=
Gray=
Left Front Positive (LF+)
Left Front Negative (LF-)
Left Rear Positive (LR+)
Left Rear Negative (LR-)
Chassis Ground
+ 12V Constant Power
+ 12V Accessory
+ 12V Power Antenna
AMP Remote
Right Front Positive (RF+)
Gray/Black=
Violet=
Violet/Black=
Orange=
Lt. Green=
Purple/White=
Brown=
Pink=
DIP SWITCH
• For Pioneer set 14 to ON (Down)
• For Sony set 14 to OFF (Up)
• All other brands #1,2,3,4 to OFF (Up)
© 2021 SCOSCHE INDUSTRIES , IN C.
8
Right Front Negative (RF-)
Right Rear Positive (RR+)
Right Rear Negative (RR-)
Illumination
Park Brake
Reverse
Mute
Speed Pulse (VSS)
1 2 3 4
DIP ON~
ITCFD0SAB 10 /2 1

ITCFDOSAB WIRING DIAGRAM
FIGURE2
0 G e
00 G G>
© 2021 SCOSCHE INDUSTRIES, IN C.
~~
C C C C C
a: a: a: a: a:
-0
0 N
~
'St' -0
Connect to Climate Control
Panel Harne ss
9
o e
For Shaker Equipped Systems
Shaker interface should be ronnected
•
to C and l should be plugged into the
other end of the interface.
M. Connect to aftermarket radio
(See Color Codes)
N. Connect to aftermarket radio's AMP
remote (Blue/White)
0. Connect to aftermarket radio's AMP
remote (Blue/White)
0 0
e
If Not Equipped with Shaker
If the vehicle doesn't have
Shaker, then plug connector P
directfy into C and ronnect the
speaker wires from the after
market radio to the wires at Q I
e
IT CFDOSAB 10 /21

CLIMATE & CONVENIENCE CONTROLS SINGLE ZONE Left screen
The Scosche Touch Screen Interface replaces the Factory climate, convenience and personalization controls built into the Factory
Ford Radio/Dash panel. This solution provides improved ergonomics while adding touch screen capabilities unique to th is
system. Read the following sections to familiarize yourself with the operating controls and settings .
FIGURE 3
LEn TOUCHSCREEN ~[llifill ~[3 ~~ BUTION LAYOUT
1. iJower ON / Of- F
2. Air Cond111oning ON/ mf-
3. Rc-urcula 11 on ON/ Olf
4. Max A/CON/ OFF
5. f-a n Spee d down{-)
6. Fa n Speed Up (1)
7. /1 1r fl ow Speed l ndica l or
8. Air Temp. Coo l
9. Air Temp. I nd i ca t or Bars
1 o. Air 1emp War m
11. /lj( Di r ectional A,rl l ow
4
C)
1. Press the Power Button (Fig.3, #1) to toggle the climate controls On or Off.
2. Press the Air Conditioning Button (Fig. 3, 12) to turn the Air Conditioning On or Off.A li ght will illuminate in the
button indicating the on/off status of the A/C.
MAX*
3. Press the recirculation button (Fig. 3, 13) to turn on air recirculation .A light will il luminate in the button indicating
the on/off status of the Recirculate mode. Interior air will be re-circulated inside the vehicle. This mode helps to
quickly cool the air inside the vehicle or prevent outside air and odors from entering. Operating recirculation mode
[while theA/C is off] increases humidity and may cause the windows to fog . Recirculation is not available in the
Defrost or Defog modes.
4. MAAA/C button (Fig. 3, 14) on the colorTFTtouch screen to turn on MaxA/C Maximum cooling will occur with the
temperature is adjusted to lowest cold setting and the Fan speed is set at maximum. MAX A/C is used to cool the car
down as quickly as possible. Touch the Max A/C button again to return to the previous Fan speed and temp setting .
5. To decrease fan speed, press the fan speed DOWN button (Fig. 3, 15) .A graphic level indicator will move down on
the color m screen indicating the current fan speed (Fig. 3, 17) .
6. To increase fan speed, press the fan speed UP button (Fig. 3, 16). A graphic level indicator will move up on the
color m screen indicating the current fan speed (Fig. 3, 17) . There are a total of 7 fan speed i ncrements from off to
maximum.
AIR FLOW /VENTCONTROL(Ag.3,111)
Touch the vent control mode icons (Fig.3, 111 on the color TFT touch screen to select vent mode . Graphics are displayed according to the selected
vent and airflow pattern.
• Airflow to • Airflow to instrument
.._,, instrument panel ;,, panel and floor vent
vent outlets. outlets .
9 • Airflow to front and .,._ 4iJ • Airflow to
..I rear windows only ._-,., instrument panel
._,- directed to the vents and rear
vent outlets. window
© 2021 SCOSCHE INDUSTRIES, INC.
• Airflow directed to
,,, floor vent outlets
A See above (4) for
MAX V more details
10
Q • Airflow directed to
,, windshield, floor and/
" or side vent outlets .
Ind i cation light will
illuminate on right
screen (See page 11 ).
ITCFDOSAB 10 /2 1