Scott Genius LT 2016 User manual

WWW.SCOTT-SPORTS.COM
WWW.SCOTT-SPORTS.COM
SCOTT Sports SA
Route du Crochet 17, CH–1762 Givisiez
Phone: [phone] | Fax: [phone]
Email: [e-mail]
All rights reserved © 2016 SCOTT Sports SA
Distribution:
SSG (Europe) Distribution Center SA, P.E.D. Zone C1, Rue du Kiell 60, 6790 Aubange, Belgium
v6.1/30082016
SCOTT GENIUS LT
USER MANUAL 2016

WWW.SCOTT-SPORTS.COM
ENGLISHENGLISH
Genius LT Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04
TC Shock Technology/Twinloc Levers . . . . . . . . . . . . . . . . . . . . . 06
Assembly of the Remote Cable . . . . . . . . . . . . . . . . . . . . . . . . . 09
FOX Nude Shock and Twinloc Remote Control Lever . . . . . . . . . . . . . 10
Basic Set-Up of the Twinloc Remote Control of FOX Nude Shock . . . . . . 11
Basic Set-Up of the Twinloc Remote Control of Fox CTD Shock . . . . . . . 13
Recommended Tools for the Shock Set-Up . . . . . . . . . . . . . . . . . . . 13
Set-Up Genius LT With FOX Nude Or FOX CTD Shock . . . . . . . . . . . . .14
SAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Set-Up of Rebound FOX Nude Or FOX CTD Shock . . . . . . . . . . . . . . .16
Set-Up of Other Shock Models . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Headset Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Bottom Bracket (BB) on Genius LT . . . . . . . . . . . . . . . . . . . . . . . . 19
Adjustable BB Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Front Derailleur (FD) Mounting Details . . . . . . . . . . . . . . . . . . . . . .21
Chainguide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Genius LT Cable Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Adjustment of Seatpost-Height . . . . . . . . . . . . . . . . . . . . . . . . . .27
Replaceable Dropout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Rear Disc Brake Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Front Fork Set-Up/Change of Front Fork . . . . . . . . . . . . . . . . . . . .29
Pivot Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
•CONTENTS
The Genius LT should be adjusted exactly to the current rider for
reaching maximum safety and fun while riding.
All adjustments should be done at the local SCOTT dealer or
following to this manual.
In order to avoid technical problems or any harm please contact
in case of doubts your authorized SCOTT dealer.
If a defined tightening torque is indicated in the manual or
on the part itself please always use a torque key and respect
that maximum indicated to make sure you do not over-tighten
bolts and screws.
03 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 02

GENIUS LT
S S M M L L
LOW BB SETTING HIGH BB SETTING LOW BB SETTING HIGH BB SETTING LOW BB SETTING HIGH BB SETTING
AHEAD TUBE ANGLE 66.3 ° 66.8 ° 66.3 ° 66.8 ° 66.3 ° 66.8 °
BHEAD TUBE LENGTH 100.0 mm 3.9 in 100.0 mm 3.9 in 110.0 mm 4.3 in 110.0 mm 4.3 in 120.0 mm 4.7 in 120.0 mm 4.7 in
CTOP TUBE HORIZONTAL 570.0 mm 22.4 in 568.7 mm 22.4 in 600.0 mm 23.6 in 598.7 mm 23.6 in 625.0 mm 24.6 in 623.6 mm 24.6 in
DSTANDOVER HEIGHT 760.6 mm 29.9 in 763.3 mm 30.1 in 758.4 mm 29.9 in 761.3 mm 30.0 in 757. 2 mm 29.8 in 760.3 mm 29.9 in
EBB OFFSET -11.0 mm -0.4 in -5.2 mm -0.2 in -11.0 mm -0.4 in -5.2 mm -0.2 in -11.0 mm -0.4 in -5.2 mm -0.2 in
FBB HEIGHT 346.0 mm 13.6 in 351.8 mm 13.9 in 346.0 mm 13.6 in 351.8 mm 13.9 in 346.0 mm 13.6 in 351.8 mm 13.9 in
GWHEEL BASE 1’145.0 mm 45.1 in 1’144.0 mm 45.0 in 1’176.4 mm 46.3 in 1’175.4 mm 46.3 in 1’202.8 mm 47. 4 in 1’201.8 mm 47.3 i n
HBB CENTER TO TOPTUBE CENTER
IBB CENTER TO TOP OF SEATTUBE 415.0 mm 16.3 in 415.0 mm 16.3 in 440.0 mm 17.3 in 440.0 mm 17. 3 in 475.0 mm 18.7 in 475.0 mm 18.7 in
JSE AT ANG LE 74.0 ° 74.5 ° 74.0 ° 74.5 ° 74.0 ° 74.5 °
KCH AI NSTAY 440.0 mm 17.3 in 438.8 mm 17. 3 in 440.0 mm 17.3 in 438.8 mm 17. 3 in 440.0 mm 17.3 in 438.8 mm 17. 3 in
LREACH 396.6 mm 15.6 in 401.5 mm 15.8 in 424.0 mm 16.7 in 428.9 mm 16.9 in 446.4 mm 17.6 in 451.2 mm 17. 8 in
MSTACK 604.5 mm 23.8 in 601.2 mm 23.7 in 613.6 mm 24.2 in 610.2 mm 24.0 in 622.8 mm 24.5 in 619.3 mm 24.4 in
NSTEM LENGTH 50.0 mm 2.0 in 50.0 mm 2.0 in 50.0 mm 2.0 in 50.0 mm 2.0 in 60.0 mm 2.4 in 60.0 mm 2.4 in
GENIUS LT PLUS
S S M M L L
LOW BB SETTING HIGH BB SETTING LOW BB SETTING HIGH BB SETTING LOW BB SETTING HIGH BB SETTING
AHEAD TUBE ANGLE 65.8 ° 66.3 ° 65.8 ° 66.3 ° 65.8 ° 66.3 °
BHEAD TUBE LENGTH 100.0 mm 3.9 in 100.0 mm 3.9 in 110.0 mm 4.3 in 110.0 mm 4.3 in 120.0 mm 4.7 in 120.0 mm 4.7 in
CTOP TUBE HORIZONTAL 570.0 mm 22.4 in 570.0 mm 22.4 in 600.0 mm 23.6 in 600.0 mm 23.6 in 625.0 mm 24.6 in 625.0 mm 24.6 in
DSTANDOVER HEIGHT 815.0 mm 32.1 in 818.0 mm 32.2 in 820.0 mm 32.3 in 823.0 mm 32.4 in 832.0 mm 32.8 in 835.0 mm 32.9 in
EBB OFFSET -20.0 mm -0.8 in -20.0 mm -0.8 in -20.0 mm -0.8 in -20.0 mm -0.8 in -20.0 mm -0.8 in -20.0 mm -0.8 in
FBB HEIGHT 345.0 mm 13.6 in 345.0 mm 13.6 in 345.0 mm 13.6 in 345.0 mm 13.6 in 345.0 mm 13.6 in 345.0 mm 13.6 in
GWHEEL BASE 1’161.0 mm 45.7 in 1’160.0 mm 45.7 in 1’192.0 mm 46.9 in 1’191.0 mm 46.9 in 1’219.0 mm 48.0 in 1’218.0 mm 48.0 in
HBB CENTER TO TOPTUBE CENTER 335.0 mm 13.2 in 335.0 mm 13.2 in 335.0 mm 13.2 in 335.0 mm 13.2 in 350.0 mm 13.8 in 350.0 mm 13.8 in
IBB CENTER TO TOP OF SEATTUBE 415.0 mm 16.3 in 415.0 mm 16.3 in 440.0 mm 17.3 in 440.0 mm 17. 3 in 475.0 mm 18.7 in 475.0 mm 18.7 in
JSE AT ANG LE 74.0 ° 74.5 ° 74.0 ° 74.5 ° 74.0 ° 74.5 °
KCH AI NSTAY 448.0 mm 17. 6 in 448.0 mm 17. 6 in 448.0 mm 17.6 in 448.0 mm 17. 6 in 448.0 mm 17.6 in 448.0 mm 17. 6 in
LREACH 390.0 mm 15.4 in 394.0 mm 15.5 in 417.0 mm 16.4 in 421.0 mm 16.6 in 439.0 mm 17.3 in 443.0 mm 17.4 in
MSTACK 608.0 mm 23.9 in 605.0 mm 23.8 in 618.0 mm 24.3 in 615.0 mm 24.2 in 627. 0 mm 24.7 in 624.0 mm 24.6 in
NSTEM LENGTH 40.0 mm 1.6 in 40.0 mm 1.6 in 50.0 mm 2.0 in 50.0 mm 2.0 in 60.0 mm 2.4 in 60.0 mm 2.4 in
ENGLISHENGLISH
•GEOMETRY/TECHNICAL DATA GENIUS LT / PLUS •GENIUS LT CONCEPT
The new Genius LT is the result of 2 years of research and development for one of the
lightest all-mountain bike frame set available on the market, hitting the scale at below
2550grams (5.60lbs) including the frame, FOX Nude/FOX Float CTD shock and the unique
TWINLOC XL remote control.
SCOTT’s focus was not only on lightweight but also on a durable and stiff frame with an
innovative suspension technology in combination with an optimized kinematics of the rear
swingarm.
The combination of an optimized kinematics with an extraordinary suspension technology
closes the gap between very light dual suspension trail bikes (e.g. SCOTT Genius) and the
new generation of freeride bikes (e.g. SCOTT Voltage FR).
Genius LT was designed for riders looking for a dual suspended all mountain and trail bike
offering a maximum rear wheel travel of 170mm.
SCOTT does not see frame and rear shock as single components which are assembled
together on a bike, but as a concept with all these components working together and
offering an outrageous function by matching perfectly.
The Genius LT Concept is based on a multi-pivot technology.
The damping performance was improved in comparison to the already famous “old” Genius
LT, and with reworking also the kinematics we were able to reach a better progression in the
end of the stroke/travel of the swingarm.
The SCOTT system, using the FOX Nude shock, will allow you to reduce by remote control
the rear wheel travel from 170 mm to 136mm including a more progressive spring rate but
still offering a supple break away.
Some models of Genius LT use also the FOX CTD shock which offers instead of the Traction
Mode a Platform (Ride Mode) in between Climb Mode and Descent Mode.
No power will be lost and an optimum power transfer is guaranteed as the swingarm, in
contrary to locked or automatic-locking systems, can follow the trail surface and will offer
perfect traction and higher speed while standing on the pedals.
Travel 170/136/0mm
Suspension Ratio 2.72
Piston stroke LT: 62.5mm / Plus: 60mm
Shock length
(EyetoEye)
217mm
Hardware Mainframe 22.2mm x 8mm
Hardware Swingarm 22.2mm x 8mm
Seatpost diameter 31.6mm
Headset semi integr. for tapered 1 1/8-1.5 (44/54.9mm Inner
diameter of frame) or with 1 1/8 straight (44.0mm)
Fork travel LT: 170mm / Plus: 160mm
Fork length LT: 564mm / Plus: 567mm
BB housing BB PF 92
Front derailleur Shimano E-Type/SRAM S3 direct mount
Bearings 2 x IGUS / 6 x 6802 (24 x 15 x 5)
05 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 04

ENGLISHENGLISH
•TC SHOCK TECHNOLOGY/TWINLOC LEVERS
The heart of the TC-System is the FOX Nude Shock made by FOX, offering three functions
which make this system possible.
The TWINLOC XL remote control lever is the evolution of the already outstanding TRACLOC
system of SCOTT.
While TRACLOC allowed only the change on the SCOTT TC rear shocks between the
SCOTT patented Lock-out, traction and full-mode on the fly from the handlebar, the
TWINLOC allows also the remote control of the front fork to shift between lock-out and
open mode at the same time when you change the modes on the SCOTT rear shox.
In combination with FOX 34 CTD forks it is also possible to have a platform mode on
the fork.
The 3 modes of CTCD in combination with FOX Nude are:
-Climb Mode : lock-out rear, lock-out front
-Traction Mode: traction mode rear (incl. Geometry change and reduced travel), platform
mode front
-Descent Mode: full travel rear (Descent), full travel front
The 3 modes of CTD in combination with the FOX CTD shock are:
-Climb Mode : lock-out rear, lock-out front
-Ride Mode: platform (Ride) mode rear, platform mode front
-Descent Mode: full travel rear (Descent), full travel front
Therefore SCOTT offers 2 different TWINLOC levers with following fork/rear shock
combinations:
-FOX Nude with different rolls for FOX CTD fork and RockShox DNA 3 fork
(SCOTTArticle number: 230097)
-FOX CTD with different rolls for FOX CTD fork and RockShox DNA 3 fork (SCOTTArticle
number: 230098)
Please note that the FOX CTD rear shock does not offer a traction mode, but a platform
mode. In contrary to FOX Nude the air-chamber volume of the positive chamber remains the
same throughout the different modes
IMPORTANT!
You can only assemble the TWINLOC remote lever in “left side upward position” on the
handlebar.
You have 3 positions of the TWINLOC remote lever.
1. LOCK OUT MODE:
the shock is locked; climbing on asphalt roads is now possible without any power loss.
Simultaneous a blow-off-system prevents the shock being damaged in case the rider did
not open the system while crossing obstacles.
2. TRACTION/RIDE MODE:
For Traction: by reducing the internal chamber volume inside the shock the travel of the
shock will be reduced to around 80% (approx. 136mm) the characteristic of the air spring
gets harder, the SAG is shorter and the geometry steeper. This results in climbing without
“bobbing” and offers still optimum traction of the rear wheel.
For Ride: by adding a platform on the compression damping system the shock will not
bounce while standing on the pedals
3. DESCENT MODE:
full travel of 170mm
You will find the following positions on the remote lever:
For the assembly of the remote control of the front fork lock-out 2 different cable rolls which
are changeable are existing.
The different roll for the pull of the fork remote cable can be changed within few minutes to
adapt the lever to your fork model/brand.
You will see on the downside of the roll the indication of the fork brand or the fork model.
07 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 06

ENGLISHENGLISH
SCOTT offers 2 different TWINLOC levers with following fork/rear shock combinations:
-FOX Nude with different rolls for FOX CTD fork and RockShox DNA 3 fork
(SCOTTArticle number: 230097)
-FOX CTD with different rolls for FOX CTD fork and RockShox DNA 3 fork (SCOTTArticle
number: 230098)
Please kindly note that the cable roll of a RockShox DNA3 or FOX CTD fork-lever is not
interchangeable with the regular rolls of 2 step forks. You need to use another lever!
For more details please contact your authorized SCOTT dealer.
To change the rolls to match another fork brand pls follow the drawings below:
ROLL FORK MOUNTING
ROLL FORK UNMOUNTING
•ASSEMBLY OF THE REMOTE CABLE
IMPORTANT!
Please make sure the lockout of SRAM/RockShox or FOX fork is activated after transport
correctly. Therefore please compress fork 5-10 times before following the manual on remote
cable installation and adjustment.
The lever should show on the downside of the cable roll the brand name of the fork you are
going to use. Please do not try to use a RockShox roll with a FOX fork or vice versa.
1. To assemble the cable please bring the
lever into the Descent Mode, push the
cable into the lever-eyelet as shown
on drawing below, push it through the
pre-cut cable housing and fix it at the
assembly unit on top of the right side of
the fork crown.
2. Fix the cable with the 2mm allen screw on the barrel adjuster
on the fork crown with a tightening torque of 0.9Nm/8 lb/in,
cut the cable and secure it with a cable end-cap. Please refer
for this action also to the manual of SRAM/RockShox or FOX
attached to the bike.
TIP:
To check for accurate cable tension, please try to move the plastic end cap of the cable
housing at the barrel adjuster on the remote lever. There should be “no-play” between cap
and barrel adjuster. In case of “play” please turn the barrel adjuster clockwise until “no-play”.
09 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 08

L5
L1
L4
L2
L3
S6
S7
S4
S3S8
S9
S2 S1
S5S7S4
ENGLISHENGLISH
•FOX NUDE SHOCK AND TWINLOC REMOTE CONTROL LEVER
In the drawing of the shock and remote lever, shown below, you will see the parts indicated
with numbers which will be used in the manual for the adjustment and setup.
Parts List
S1 Front eyelet/ Shock Bolt
S2 Rear eyelet/ Shock Bolt
S3 Shock Housing
S4 Rebound-Adjuster Knob
S5 Positive Chamber Valve
S6 Remote Control Wheel
S7 Cable Fixing Screw
(hidden behind remote wheel)
S8 Shock Piston
S9 SAG Indicator (o-ring on piston)
L1 Remote Lever
L2 Release button
L3 Remote Control Cables
L4 Cable Tension Screw Fork Remote
L5 Cable Tension Screw Shock Remote
•BASIC SET-UP OF THE TWINLOC REMOTE CONTROL OF FOX
NUDE SHOCK
To ensure perfect function of the FOX Nude shock it is very important to follow the steps
shown below exactly.
On Genius LT Carbon frames you will find an internal cable routing.
Push the inner cable first through the remote
lever in the upper cable routing of the lever and
then through the cable housing as shown below
inside the toptube.
On Genius LT alloy frames a regular
outside cable routing, the outer
cable housing is fixed on cable
mount ports with cable zippers.
1. loosen the cable fixing screw (S7) by turning it
counter clockwise with a 2mm allen key.
2. insert a new cable via lever hole and cable
housing and push it into the shock as shown
around the remote wheel (S6).
11 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 10

ENGLISHENGLISH
3. tighten the cable and fix the cablefixing screw
(S7) by turning it clockwise with a 2mm allen
key and a max. tightening torque of 1.6Nm.
4. Check that the handlebar lever
is in the traction position. Refer
to the following diagrams.
5. cut the cable approx. 20mm away from the
remote wheel. Fix it by squeezing it with pliers.
6. push a cable end-cap on the cable until it
touches the end of the cable. Fix it by squeezing
it with pliers.
•BASIC SET-UP OF THE TWINLOC REMOTE CONTROL OF FOX
CTD SHOCK
The assembly of the remote cable and the setup of the FOX CTD rear shock is very similar to
the abovementioned assembly and setup of the FOX Nude.
For more details on the FOX CTD please follow the details shown in the manuals of FOX
attached to this bike.
•RECOMMENDED TOOLS FOR THE SHOCK SET-UP
For the set-up of the shock we recommend to use a shock pump with a scale up to 20
bars/300 psi with a special air valve connector preventing from air getting away while
removing the pump from the shock valve, this will result in an exact air pressure.
Please note that air will flow into the hose and indicator when counterchecking the air
pressure, so you have to set up again the recommended pressure after this action.
Make sure to balance at least this air loss when you make a check of the air pressure of the
shock. Please also note that the indicators of shock pumps have a tolerance of max. 10%.
13 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 12

ENGLISHENGLISH
•SET-UP GENIUS LT WITH FOX NUDE OR FOX CTD SHOCK
The Set-Up of the FOX Nude or FOX CTD Shock can be easy done within a few minutes.
IMPORTANT!
For all adjustments of the air spring the remote lever has to be in position “alltravel”
To adjust the air pressure of the air chamber of the FOX Nude or FOX CTD Shock please
refer to the following instruction:
1. Remove the valve cap of the valve (S5) located on the shock housing (S3).
2. Mount the shock pump with its adaptor on the valve
3. Please take into account that it takes some air pressure from inside the shock to drive the
indicator on the pump. Make sure to balance at least this air loss when you make a check
of the air pressure of the shock. Pls also note that the indicators of shock pumps have a
tolerance of max. 10%
4. Please use the FOX iRD App available at the iTunes App store with following link:
https://itunes.apple.com/us/app/fox-intelligent-ride-dynamics/id549035102?mt=8&ign-
mpt=uo%3D4)
5. After downloading the app on your mobile gear please follow the steps shown in the app
and inflate the shock according to the air pressure indicated.
6. When you reached the needed pressure remove the pump and put the valve cap on
the valve.
•SAG
The SAG should be 18mm on the shock piston.
To check the adjustment, please follow as shown below:
1. sit on the bike, put your feet on the pedal
2. put your feet back on the ground and stand over the bike without bouncing the bike
during this action
3. check if the o-ring (S9) on the shock piston (S8) has a distance of 18mm to the main dust
wiper/seal between shock housing and piston.
-if the distance between the o-ring and the main dust wiper/seal is 18mm, the air pressure
is matching to your weight
-if the distance between the o-ring and the main dust wiper/seal is less than 18mm, the
air pressure of the air chamber is too high and should be carefully reduced by using the
bleed knob of the shock pump until the distance is 18mm.
-if the distance between the main dust wiper/seal is bigger than 18mm the air pressure
of the air chamber is too low and should be increased by using the shock pump until the
distance is 18mm.
15 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 14

ENGLISHENGLISH
IMPORTANT!
After a dismantlement of the rear shock, both fixing bolts should be tightened with a
tightening torque of 10Nm/88in-lbs.
If this is not done correctly the rear shock can be damaged.
•SET-UP OF OTHER SHOCK MODELS
SCOTT strongly recommends using only the FOX Nude (FOX CTD shock) with the
Genius LT bike, as we designed both parts for a perfect matching combination with a linear
suspension rate.
Also on those shock models the SAG should be 18mm.
Other Shock Models on Genius LT
If you want to use a different rear shock model than the one originally on the bike, please
make sure that the shock will not in any position hit the frame and cause a damage to
the frame.
Please follow the instruction below:
-Please make sure that the rear shock or its accessory parts do not touch the frame when
mounting or suspending.
-For doing so release the air/remove the coil, install the shock and compress the shock
completely.
-If the shock touches the frame while doing so, do not use this shock in order to avoid
damage to frame, swingarm or shock.
•SET-UP OF REBOUND FOX NUDE OR FOX CTD SHOCK
“Rebound” describes the speed the shock comes back to its original length after absorbing
an obstacle.
By using the rebound adjuster knob (S4) you can adjust the rebound step by step.
Please refer to the following instruction:
Ride your bike off a pavement (remain in the saddle) and check how many times it bounces.
-If it bounces 1-2 times, the set up is good.
-If it bounces more than 3 times the rebound is too fast. Turn the knob 1-2 “clicks”
clockwise
-If it does not bounce the rebound is too slow. Turn the knob 1-2 “clicks” counter
clockwise.
IMPORTANT!
Note that you have to mount the FOX
Nude Shock always as shown below.
Mounting the rear shock in a different
position can cause severe damage to
the frame, the linkage levers and the
rear shock.
Same for the FOX CTD on some of the
Genius LT models.
17 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 16

ENGLISHENGLISH
•HEADSET OPTIONS
Genius LT features a tapered headset and
fork steerer system to match with semi-
integrated headsets of the “50-61”mm
range with ID of Headtube of 44.0mm on
top and 54.9mm on the lower end.
Ritchey WCS Carbon Zero Tapered PF 50-61mm 18mm UD PRD 13636
Ritchey PRO Tapered PF 50-61mm 12.9mm PRD 13640
It is also possible to use forks with a standard 1 1/8” steerer tube when using a reducer
headset such as e.g.
Ritchey WCS Carbon Zero Tapered PF 50-61mm 18mm UD for 1 1/18" fork PRD 14860
•BOTTOM BRACKET (BB) ON GENIUS LT
All frames of Genius LT (carbon and alloy) have a BB shell for BB92PF standard.
The BB housing has actually a width of 89.5mm.
IMPORTANT!
Please note that you need a 2.5mm spacer on the BB axle or between BB cup and frame
on the right side of the BB shell.
19 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 18

ENGLISHENGLISH
•ADJUSTABLE BB HEIGHT
On Genius LT bikes equipped with the FOX Nude or the FOX CTD shock you can adjust the
BB height above ground in 2 positions by flipping a geometry chip located on the linkage
bar shock mount.
Only use the appropriate adaptor.
•FRONT DERAILLEUR (FD) MOUNTING DETAILS
On all Genius LT frames you
will find a Shimano E-type
front derailleur but fixed
directly on the swingarm
without the plate that is fixed
normally between the bottom
bracket bearing cup and the
bottom bracket housing of
the front triangle or a SRAM
Direct Mount Type S3 FD.
Please note that you always
need to use the adapter plate
attached to the bike or frame
set between chainstay and
front derailleur.
This adapter can be ordered at the SCOTT distribution with parts number:
235277 FD mount plate Set Genius LT 700 2014
Please note that the adapter is not interchangeable!
1. low BB for lower center of gravity over ground
2. high BB for bigger clearance between pedals/crankset and obstacles on the ground
IMPORTANT!
It is not possible to use this geometry chip with other shock models than the FOX Nude or
FOX CTD.
The shock might collide with parts of the frame or linkage bar.
21 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 20

ENGLISHENGLISH
•CHAINGUIDE
The Carbon as well as the alloy frames of Genius LT can be fitted with ISCG chainguide
systems.
A set of all spare parts for this action can be ordered via the SCOTT distribution with:
229730 ISCG adaptor Genius 2013
Details for the assembly on the carbon frames of Genius LT:
The adaptor must be used in order to assemble the chainblocker on the ISCG05
chainguide system.
Please note that you need to assemble the chainblocker exactly the way as shown and use
all parts of the set.
Please also respect the different assembly positions for SRAM and Shimano front derailleurs
For 2x10 drivetrains you need to use 2x2.5mm washers, for 3x10 drive trains 1x2.5mm
washers between adaptor/frame and the chainblocker as shown.
Details for the assembly on the alloy frames of Genius LT:
You can assemble the chainblocker directly on the integrated ISCG05 mount on the BB shell.
Please respect the different assembly positions for SRAM and Shimano front derailleurs.
In addition to the chainblocker assembled on the Genius LT you also find a chainguide
mounting port below the chainstay.
Both frame options, carbon and alloy, have the same feature.
You can use 2 different versions:
1. single chainring
2. double chainring
In case the chainguide is once worn out by the chain running through the guide you can
order a service kit with article numbers:
235291 Chainguide Genius LT 2014 single Speed
235292 Chainguide Genius LT 2014 double Speed
To assemble the parts please follow following points:
1. insert the chain between the 2 parts of
the cage
2. insert the steel tube through the plastic
chain guide hole
3. tighten the bolt with maximum
4Nm/35in-lbs
23 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 22

USE PLASTIC GUIDE TO FIX THE BRAKE CABLE
ENGLISHENGLISH
•GENIUS LT CABLE ROUTING
The direct and straight cable system on all our full suspension models offers perfect shifting
performance combined with lightweight and high resistance against water and dirt.
CARBON FRONT FRAMES
The carbon frames of Genius LT have an internal shifting cable routing with cable stops on
the front end of the downtube as shown in the diagram.
FD: Front derailleur
RD: rear derailleur
BR: rear brake
SP: seatpost remote
Insert the cables into the
headtube as shown:
Pull the cables out in the BB area:
Guide the seatpost remote cable upwards to the seatpost inside the frame (stealth) or pull it
out on the rear-side of the seattube.
Push the cable port parts into the frame and fix the port with a 3mm allen key with a
maximum torque of 4Nm/35in-lbs
Headtube section: BB section:
Please make sure to respect the 40mm distance between the cables and the BB (bottom
bracket) housing to avoid “ghost-shifting” and/or damages on the shift cables and
brake hose.
For the rear brake please assemble the cable as shown
in the following drawings:
Please keep in mind to have a minimum distance of
40mm between the brake hose and the BB housing as
abovementioned!
Please fix the brake hose and the remote seatpost
cable housing (if applicable) on the frame on the cable
mounts with the mount clips by following the routing
info as shown:
25 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 24

ENGLISHENGLISH
In order to seal the housing ports on the frame you
should use the plugs attached to the bike.
Please secure the clamps
with a cable zipper as shown:
The cable guide can be ordered via the SCOTT distribution with parts number:
229723 BB Cable Guide Genius (f. Carbon Frame)
ALLOY FRONT FRAMES
Please fix the derailleur cable housings,
the brake hose and the remote
seatpost cable housing (if applicable)
on the frame on the cable mounts with
the mount clips by following the routing
info as shown below:
Please secure the clamps with
maximum 4Nm/35in-lbs as shown:
IMPORTANT!
Please make sure to respect the 40mm distance between the cables and the BB (bottom
bracket) housing to avoid “ghost-shifting” and/or damages on the shift cables and
brake hose.
229724 Cable Clamping Set Genius alloy 2013 one size
•ADJUSTMENT OF SEATPOST-HEIGHT
IMPORTANT!
The seatpost has to be inserted into the seattube at a minimum of 100mm.
Never use another seatpost diameter than 31.6mm or try to use a shim/reducer between
seatpost and frame.
27 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 26

ENGLISHENGLISH
For 185mm rotor diameter you will need 2 red anodized spacers that can be ordered via the
SCOTT distribution with:
219568 Brake Mount Adapt.Spacers 4mm f/185mm
For the 200mm rotors please use for: SRAM/Avid: “+20mm” adapter
Shimano: F180PP2
•FRONT FORK SET-UP/CHANGE OF FRONT FORK
For the set up of the front fork please use the fork specific manual attached to the bike.
We recommend using front forks with a travel of 170mm (700) and 160mm (Plus) as this will
not influence the geometry and alter handling of the bike.
For details on the technical length of the recommended forks please refer to the Tech Info
Chart before mentioned.
•PIVOT MAINTENANCE
The pivot and bearings on SCOTT Genius LT are extremely easy to maintain.
An external treatment with a grease spray after every bike wash is all you have to do. We
do not recommend heavy grease sprays since these will leave a film on the parts which is
difficult to remove. We recommend the same for the chain also.
If you have to change the bearings you can order them included in a service kit at your local
SCOTT dealer or buy them with international parts number as shown above in the specs list
in a hardware store.
In case of a change of the bearings or of the rear swingarm you should contact your local
SCOTT dealer as you need special tools for disassembly and assembly.
•REPLACEABLE DROPOUT
On Genius LT bikes of model year 2013 you can replace the rear derailleur hanger.
Depending on the different models you’ll find following options:
1. 142mm axle with RWS 142/12
This is available via the SCOTT distribution:
219574 complete set of RWS 142/12
219577 right side replaceable RD hanger
2. 135mm axle with RWS 135/5
This is available via the SCOTT distribution:
219572 complete set of RWS 135/5
219575 right side replaceable RD hanger
3. Regular 135mm rear axle with QR
This is available via the SCOTT distribution:
206473 replaceable hanger
If you want to use another RWS standard SCOTT also offers after-market parts for specific
wheelsets for the following parts via the SCOTT distribution:
219574 RWS 135/12 parts set
219576 right side replaceable RD hanger
•REAR DISC BRAKE MOUNT
Genius LT can be used with 3 different disc
rotor sizes on the rear brake.
The rear disc brake on Genius LT is
Postmount (PM) Standard on the left
seatstay and it is possible to use disc rotors
with 180, 185 and 200mm diameter.
Please note that for the assembly of 185 and
200mm rotors you might need adapters/
washers between the PM port on the frame
and the brake calliper.
29 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 28

ENGLISHENGLISH
•WARRANTY
SCOTT bikes are made using the most innovative production and quality methods. They are
equipped with best components of well known parts suppliers.
Doing so SCOTT warrants its frames and swingarms for five years (subject to compliance
with maintenance ranges, see below) and SCOTT forks (provided it is a fork of SCOTT) for
two years for defects in material and/or workmanship in case of purchase of completely
assembled bikes.
This warranty of 5 years for the frames shall only be granted in case once a year a
maintenance service has been effected according to maintenance requirements as set forth
in this manual by an authorised SCOTT dealer.
The authorised SCOTT dealer shall confirm the effected annual maintenance service by
stamp and signature.
In case such an annual maintenance service has not been effected the warranty of 5years
for the frame shall be reduced to 3 years.
Costs for maintenance and service have to be born by the owner of the SCOTT bike.
On Gambler, Voltage Fr and Volt-X the warranty period is limited to 2 years.
The warranty period starts at the day of purchase. This warranty is limited to the first buyer,
what means the first person who uses the bike and only with the use it was made for.
Furthermore, this warranty is limited to purchases via authorized SCOTT-dealers
The warranty is solely granted in case of purchase of a completely assembled bike to the
explicit exclusion of purchases of not completely assembled bikes.
In case of a warranty claim the decision to repair or to replace the defective part is up to
SCOTT. Non defective parts will only be replaced at the guarantee’s own expense.
Fair wear and tear is not covered by the warranty.
A complete list of all parts of wear and tear can be found in the next chapter of this manual.
In addition, you will find at the end of this manual a protocol for the handing over of the
bike which will remain in copy at the SCOTT dealer after acceptance and signature of the
consumer.
It is obligatory to show this protocol of handing over together with the defective part in case
of a warranty claim given that it provides evidence of purchase. Otherwise no warranty is
granted.
In principle, this warranty is granted worldwide. Claims must be made through an authorized
dealer, for information regarding the nearest dealer, write or call this company or the national
SCOTT distributor.
Normal wear, accident, neglect, abuse, improper assembly, improper maintenance by other
than an authorized dealer or use of parts or devices not consistent with the use originally
intended for the bicycle as sold are not covered by this warranty.
Hereby SCOTT grants a voluntarily manufacturer’s warranty. Additional entitlements
according to national warrant of merchantability are reserved.
For warranty info on the Fox Nude shock please refer to the attached manual of Fox Nude.
•WARRANTY
Model ...................................................................................
Year .....................................................................................
Size ......................................................................................
Frame Nr. ................................................................................
Shock Nr. ................................................................................
Date of purchase .........................................................................
31 |
2016 BIKE USER MANUAL | GENIUS LTGENIUS LT | 2016 BIKE USER MANUAL
| 30