Scott SCALE 700 User manual

WWW.SCOTT-SPORTS.COM
WWW.SCOTT-SPORTS.COM
SCOTT Sports SA
Route du Crochet 17, CH–1762 Givisiez
Phone: [phone] | Fax: [phone]
Email: [e-mail]
All rights reserved © 2017 SCOTT Sports SA
Distribution:
SSG (Europe) Distribution Center SA, P.E.D. Zone C1, Rue du Kiell 60, 6790 Aubange, Belgium
v7.0/2 105 20 1 7
USER MANUAL
SCOTT SCALE

WWW.SCOTT-SPORTS.COM
ENGLISHENGLISH
•CONTENTS
The SCOTT Scale should be adjusted exactly to the individual
rider to achieve maximum saftey and fun while riding.
SCOTT recommends that all adjustments be carried out by
your local authorized SCOTT dealer. Some basic maintenance
can be done if strictly following the manuals supplied with
this bike.
Please contact your authorized SCOTT dealer for advice in order
to avoid any harm and assist you with any questions or technical
problems.
•IMPORTANT
This manual refers to all 2018 SCOTT Scale carbon bikes and
frames, for all other bikes and frames please refer to the
correct manual or your authorised SCOTT dealer.
For SCOTT Scale 700 plus please contact your local SCOTT
dealer or refer to 2017 Scale manual and the general SCOTT
manual for more information
SCOTT SCALE 3 . . . . . . . . . . . . . . . . . . . . . . . 04
Scale Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04
Geometry/Technical Data Scale 3 900 . . . . . . . . . . . . . . . . . . . . 05
RIDELOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06
Basic Set-Up of Forks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .07
SAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
Rebound Fork Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09
Replaceable Rear Dropout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09
Brake Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cable Guides and Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
BB Standards/FD Mounting Details. . . . . . . . . . . . . . . . . . . . . . . .14
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
GUARANTEE ON SCOTT BIKES . . . . . . . . . . . . . . 16
03 |
BIKE USER MANUAL | SCALESCALE | BIKE USER MANUAL
| 02

S M L XL
AHEAD TUBE ANGLE 69.5 ° 69.5 ° 69.5 ° 69.5 °
BHEAD TUBE LENGTH 95.0 mm 3.7 in 100.0 mm 3.9 in 115.0 mm 4.5 in 125.0 mm 4.9 in
CTOP TUBE HORIZONTAL 575.0 mm 22.6 in 600.0 mm 23.6 in 625.0 mm 24.6 in 650.0 mm 25.6 in
DSTANDOVER HEIGHT 743.0 mm 29.3 in 774.0 mm 30.5 in 800.0 mm 31.5 in 835.1 mm 32.9 in
EBB OFFSET -58.0 mm -2.3 in -58.0 mm -2.3 in -58.0 mm -2.3 in -58.0 mm -2.3 in
FBB HEIGHT 312.0 mm 12.3 in 312.0 mm 12.3 in 312.0 mm 12.3 in 312.0 mm 12.3 in
GWHEEL BASE 1,076.4 mm 42.4 in 1,101.8 mm 43.4 in 1,127.9 mm 44.4 in 1,153.7 mm 45.4 in
HBB CENTER TO TOPTUBE CENTER 325.0 mm 12.8 in 375.0 mm 14.8 in 415.0 mm 16.3 in 465.0 mm 18.3 in
IBB CENTER TO TOP OF SEATTUBE 390.0 mm 15.4 in 440.0 mm 17.3 in 480.0 mm 18.9 in 530.0 mm 20.9 in
JSE AT ANGLE 73.6 ° 73.6 ° 73.6 ° 73.6 °
KCH AINSTAY 425.0 mm 16.7 in 425.0 mm 16.7 in 425.0 mm 16.7 in 425.0 mm 16.7 in
LREACH 398.7 mm 15.7 in 422.3 mm 16.6 in 443.2 mm 17. 4 in 465.5 mm 18.3 in
MSTACK 599.0 mm 23.6 in 603.6 mm 23.8 in 617.7 mm 24.3 in 627.1 mm 24.7 in
NSTEM LENGTH 60.0 mm 2.4 in 70.0 mm 2.8 in 80.0 mm 3.1 in 90.0 mm 3.5 in
0TRAIL 83.9 mm 3.3 in 83.9 mm 3.3 in 83.9 mm 3.3 in 83.9 mm 3.3 in
ENGLISHENGLISH
•SCALE CONCEPT
From the Carbon fiber to the manufacturing process to the final result- the new Scale
has been completely redesigned. The result: a new benchmark for race hardtail frames.
The Scale RC 700 SL weighs in at only 849 grams. The incredible lightweight frame
characteristics and two dedicated frame platforms for 1x and 2x drivetrains lift the standard
of hardtail mountain bikes to a new level.
A mix of high-end carbon fibers has been used on all Scale Carbon frames in order to
achieve incredible results. The HMX-SL frame utilizes MR70, YS60 and HR40 Carbon
fibers. HR40 is a strong and light filament which, used together with MR70 fibers, attains
unachieved tensile strength values. In order to achieve the set stiffness targets, YS60 layers
are added into the lay-up. After choosing the Carbon fibers, the engineers are using specific
tools, like FEA software, to map out the carbon lay-up. Thanks to SCOTT's proprietary
EvoLap-Technology, different forces can be applied on a virtual model and the frame
construction is adjusted accordingly.
The SDS2 technology achieves comfort in carbon frames without adding parts or sacrificing
stiffness characteristics. In order to achieve this, the engineers use different tube shapes in
combination with a strategic alignment of the carbon fibers to avoid any undesired flex that
can impair performance.
The Boost standard improves wheel stiffness and allows for increased tire clearance. The
new Scale frame has been developed around the Boost standard in order to maximize the
advantages of the new norm. The three millimeter outboard chain ring adds clearance to the
chainstay area allowing for a significant increase of the chainstay cross-section for both, the
1x and 2x models. This offers more possibilities to find the right position of the rear wheel in
the frame in order to achieve improved structural stiffness.
The new Scale is available in two different versions. The HMX-SL and HMX frames are
optimized for 1x drivetrains only and therefore dedicated to race-oriented riders. The HMF
line-up is designed and optimized around a double chain ring setup. These models can,
however, accommodate a single chainring configuration.
On the new Scale introduce a specific brake mount adapter which is linked directly to the
chainstay and thru-axle in order to increase stiffness.
Routing the cables internally avoids bulky external hardware and looks cleaner. Due to the
improved protection, the cables have a longer lifetime.
The new Scale chain guide weighs in at just 23 grams, is easy to assemble thanks to a smart
mounting system and can accommodate 30T to 36T chainrings.
The new Scale dropouts are designed to be integrated on the thru-axle system thanks to a
hollow tube design that allows a simple and lightweight structure.
SCOTT SCALE 3 •GEOMETRY/TECHNICAL DATA SCALE 3 900
Seatpost Diameter 31.6mm
Seattube clamp 34.9
Headset bearings: 51.9x40x8 45 ° x 45 °/
41.8x30.5x8 45 ° x 45 °
Fork travel 100mm
BB housing BB PF92
Front derailleur Shimano high direct mount side
swing (none RC models only)
Additional parts needed
Chainring size 38T max
Max tyre width 2.3/57mm
Please note:
Tire sizes often vary from brand to
brand. Ensure the tire clearance is
adequate when replacing your tires!
•IMPORTANT
Only a bottle with 0.55L capacity will
have the clearance to fit a small frame
05 |
BIKE USER MANUAL | SCALESCALE | BIKE USER MANUAL
| 04

ENGLISHENGLISH
•IMPORTANT!
SCOTT Scale 3 is designed around the BOOST platform so many of the fitted parts: cranks/
wheels/dropouts/forks differ from traditional cycle parts. Always consult your authorized
SCOTT dealer for advice on replacing or repairing any part of your SCOTT bike!
•RIDELOC
This section refers to SCOTT bikes fitted with the RIDELOC system. For all non-RIDELOC
systems please refer to the specific fork manual for your setup.
The RIDELOC system offers the rider full control of all 3 modes of the front forks with a
single lever, the position and function of the RIDELOC lever make for effortless control over
the forks function.
The 3 basic functions of RIDELOC system are:
-Climb-out Mode
-Traction Mode
-Descent Mode
There are 3 positions of the RIDELOC remote lever.
1. CLIMB MODE: The fork is nearly locked; climbing on asphalt roads is now possible with
little power loss. A simultaneous blow-off-system prevents the forks being damaged in
case the rider does not open the system while crossing obstacles.
2. TRACTION MODE: Altering the dampening of the forks will result in climbing with reduced
“bobbing” and still offers optimum control of the front wheel.
3. DESCENT MODE: Full travel of the fork.
You can only assemble the “standard” RIDELOC remote lever in “left side upward position”
on the handlebar (this is usually fitted on bikes with x2 front chainrings).
On bikes with X1 chainring on the front the under bar RIDELOC remote lever in “left side
downward” position can be fitted as standard.
It is possible to change the RIDELOC lever to the underbar option if the bikes gears have
been changed to X1 system, a new alternative lever will be required for this adjustment;
please consult your local SCOTT dealer for more information on obtaining the correct lever
for your bike.
You will find the following positions on the remote lever:
•BASIC SET-UP OF FORKS
Recommended tools for the shock setup:
-The SAG tool that came with your bike. *Fox forks only
-A shock pump with a special air valve connector (not supplied with this bike), this will
help stop air from escaping while removing the pump from the shock valve.
Please note that air will flow into the hose and indicator when counterchecking the air
pressure, this will give the appearance that the shock has less air pressure than it was setup,
your shock may need to be adjusted once this action is made.
Please also note that the indicators of shock pumps have a tolerance of max. 10%.
For bikes spec’d with Fox forks:
You can find more specific information about Fox set
up on Fox’s website, please use your fork ID number
to find more useful setup tips for your exact fork
(visit: ridefox.com)
07 |
BIKE USER MANUAL | SCALESCALE | BIKE USER MANUAL
| 06

* Fox rebound adjuster shown
ENGLISHENGLISH
•SAG
Your SCOTT bike will be supplied with a SAG tool to help set up your bikes suspension, these
SAG tools can be easily clipped on the fork body and Fork dust seal.
For the best performance it is recommended you start with SAG of 15-20% for forks.
1. Make sure before any adjustment is made that your forks are in the “open” position.
2. With the fork pump attached to the fork valve, pump your desired pressure into the fork.
Once the pressure is achieved slowly compress and decompress your fork through 25% of
its travel 10 times. This will equalize the positive and negative air chambers and will change
the pressure on the pump gauge, if needed add or reduce pressure and repeat.
Note the compression/decompression of the fork through the travel must also be done
if the pressure is reduced!
3. Once your desired pressure is reached slide the rubber O-ring on the fork leg against the
dust seal, clip on your SAG tool if required.
4. Sit on your bike in your usual riding position (in your riding gear: if you carry a bag/
Hydration-system put it on,) don’t “bounce” the suspension while doing this, use a wall or
a friend for support if needed.
5. Get off the bike gently without bouncing and check the O-ring position on the fork
stanchion, with the SAG adjuster clipped on. This makes it easy to see where your SAG is
set. Example below.
•IMPORTANT!
Do not sit on your bike with the shock pump
attached to the bike!
Sram and non-direct
mountderailleurs
SCOTT part number 254090
Shimano direct
mountderailleurs
SCOTT part number 254091
•REBOUND FORK SET-UP
“Rebound” describes the speed the fork returns back
to its original length after absorbing an obstacle,
setting of this is very important for the handling and
correct function of the bike.
The rebound adjustment dial location may vary form
fork to fork please consult the manual that came with
this bike.
After the fork pressure/SAG is correctly set ride your
bike in a safe area with your riding gear/backpack,
etc. While remaining in the saddle, ride you bike off a
drop/kerb of about 10-15 cm.
-If it bounces 1-2 times and settles the set-up is good.
-If it bounces more than 3 times the rebound is too fast, turn the knob 1-2 “clicks”
clockwise and repeat.
-If there is no bounce the rebound is too slow, turn the knob 1-2 click counter clockwise
and repeat.
-Repeat these steps until the desired result is achieved.
Your SCOTT Scale bike was designed to be used in conjunction with a specific forks,
changing the forks on your bike may cause poor/unsafe riding characteristics or damage
to frame and components, please consult your SCOTT dealer for any assistance you need,
failure to do this may affect your warranty
This is the basic principle on setting your forks up, please always consult the fork owner's
manual for full instructions to familiarize yourself with the product.
•REPLACEABLE REAR DROPOUT
On SCOTT Scale models for 2018 the rear derailleur hanger is replaceable, this hanger is
available in two options depending on if your bike is equipped with a standard or direct
mount rear derailleur.
FOR CARBON SCOTT SCALE 3 FRAMES ONLY:
09 |
BIKE USER MANUAL | SCALESCALE | BIKE USER MANUAL
| 08

ENGLISHENGLISH
If your dropout needs to be replaced, we recommend this work should be carried out by
your local SCOTT dealer as the rear derailleur may need adjustment, failure to adjust this
correctly may result in accident or damage to your bike.
•IMPORTANT!
We recommend all work should be carried out by your authorised SCOTT dealer!
If you wish to change this item yourself, please ensure the bike is supported correctly to
prevent damage. Please refer to the general manual supplied with your bike for instructions.
Before installing the new hanger first
make sure the area is clean; insert
the hanger.
Insert the end cap through the frame and
into the hanger.
Make sure the location arrow is pointing
to the lower bolt hole; insert the bolt (Max
torque 1.5 N/M)
Insert the second bolt in the rear of the
dropout (Max torque 1.5 N/M)
Once the bike is reassembled please insure the wheels are refitted correctly and the gears
are set correctly including the over shift stops, please consult your authorized SCOTT dealer
for assistance.
•BRAKE MOUNT
•IMPORTANT!
We recommend all work should be carried out by your authorised SCOTT dealer!
There is an option to use either a 160 or
180mm brake rotor on the rear of for SCOTT
Scale carbon with the use of the correct
adaptor (note this does not apply bikes with
boost Q/R).
New mounts are available from your authorized
SCOTT dealer and the size is marked on the
underside of the mount.
Part number: 254096 /160 mm brake mount.
Part number; 254095 /180 mm Brake mount.
If you wish to change this item yourself, please ensure the bike is supported correctly to
prevent damage. Please refer to the general manual supplied with your bike for instructions.
For this adaptor to be fitted you must remove the rear wheel and rear brake calliper.
Once all the correct items are removed the new mount will fit by swinging into place.
11 |
BIKE USER MANUAL | SCALESCALE | BIKE USER MANUAL
| 10

ENGLISHENGLISH
•CABLE GUIDES AND CABLING
On the SCOTT Scale carbon the cable guides on the headtube can be changed if required
so different cable configurations can be used.
The main cover plate of the cable guide is available in two options:
-HT-Blank: this can be used when no cables are to be routed.
-HT: this is open and can be used for different cable options.
If cables are to be routed you must select the correct insert for the cover depending on the
configuration you require, the inserts can be easily changed in cover plate once the cables
have been removed and the cover removed from the bike.
The inserts are marked A-E, these letters dictate what cables can be used; these are the
same for left and right.
•IMPORTANT!
For 180mm rotors, please ensure the conical washer on the front mount is fitted!
Refit the wheel and brake calliper checking the correct operation of all the components
before riding, if in any doubt please contact your SCOTT dealer for assistance and advice.
HT:
this is the cover plate
for all cable options
A:
1x Mechanical cable
D:
1x single cable & Di2
HT-Blank:
this is the no cable option
B:
2x Mechanical cables
E:
Single cable and Live valve
C:
2x mechanical cables
1x hydraulic
If you wish to change or replace the headtube cableguide set on your SCOTT Scale this kit
can be ordered from your local SCOTT dealer.
SCOTT part number: 266587 and consists of:
2x HT/A/B/C/D
1x HT-Blank/E
13 |
BIKE USER MANUAL | SCALESCALE | BIKE USER MANUAL
| 12

ENGLISHENGLISH
•ADJUSTMENT
We recommend all adjustments are carried out by your local authorized SCOTT dealer but
basic maintenance and checks should be done regularly before each ride as described in the
general manual that was supplied with your bike.
Please pay attention to all instructions and torque settings, if you have any doubts please
contact your dealer,
*in addition to the torque settings please note all bikes with a dropper type seatpost have a
seatpost clamp maximum torque of 5 N/M.
•BB STANDARDS/FD MOUNTING DETAILS
The SCOTT Scale has a Press fit PF92 bottom bracket with an inner diameter of 41mm, this
is a press fit system and special tools are required for removal and refitting, please contact
your SCOTT dealer for assistance.
The SCOTT Scale (non RC models) uses
a high direct mount side swing front
derailleur only, this must be used with the
use of an FD adaptor plate.
It is not possible to mount a front
derailleur to RC frames/bikes.
These cable guides are fitted with a single bolt, the fixing torque of this must not exceed
0.75-1 N/M.
With the many different cabling options it is possible to customise the cable routing slightly
depending what components you wish to run, it is recommended that handlebar cables
that come from the right hand side enter the frame on the left, and handlebar cables that
come from the left hand side enter the frame on the right, while this is not crucial to the
performance of the bike it may help to prevent any cable rub.
Below is an example of a bike set up “European style” with a 1X set up and a dropper seatpost.
Please note that below is an example and that your bikes brakes need to be set up as per
the law in your country, please check with your local SCOTT dealer for this information.
15 |
BIKE USER MANUAL | SCALESCALE | BIKE USER MANUAL
| 14

SCOTT Bikes
Gambler, Voltage FR, Volt-X
5
ENGLISHENGLISH
improper or incorrectly performed maintenance or repairs performed by someone other
than an authorized SCOTT dealer, use of parts or devices not consistent with the Product,
and alteration of the Product.
All Products come with a manual; please carefully follow the instructions located there
or affixed elsewhere to the Product. To the extent permitted by law, consequential and
incidental damages are not recoverable under this limited warranty.
How do you make a claim under this limited warranty?
To make a claim under this limited warranty, you must notify SCOTT of the claimed defect
within the warranty period and timely return the Product to SCOTT at your expense for
inspection. Please contact your authorized SCOTT dealer, call SCOTT’s customer service
or the national SCOTT distributor (dealer locator: www.scott-sports.com). All returned
Products must be accompanied by proof of purchase (receipt) from an authorized SCOTT
dealer or this limited warranty will not apply. In case of replacement or refund, returned
Product becomes the property of SCOTT.
A protocol for the handing over of the Product (which you will find at the end of the manual)
will remain in copy at the SCOTT dealer after acceptance and signature of the consumer. It
is obligatory to show this protocol of handing over together with the defective part in case
of a warranty claim given that it provides evidence of purchase or this limited warranty will
not apply.
How do state laws affect your rights under this limited warranty?
This limited warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state.
Recommendation
We strongly recommend that you use only authorized SCOTT dealers for yearly maintenance
services and for repairs, as improper or incorrectly performed maintenance or repairs voids
this limited warranty. Costs for maintenance service have to be borne by the consumer.
•WARNING!
SCOTT Sports SA is not responsible or liable for any injury caused by any missing
compliance with these instructions, particularly but not limited to misuse, incorrect
maintenance, incorrect set-up and handling, neglect or abuse. Failure to follow these
instructions can result in component failure, serious personal injury. Component failure
can lead to loss of control of the bicycle and result in serious personal injury.
What is Covered?
This warranty covers defects in materials and workmanship at the time of transfer of risks in
frames, swingarms and forks (provided it is a fork of SCOTT) on SCOTT branded bikes sold
completely assembled by SCOTT or an authorized SCOTT dealer (“Product”).
How long does coverage last?
This voluntary manufacturer’s warranty is limited to five years for frames and swingarms,
respectively two years for forks, from the date of purchase of the Product and is limited
to the first purchaser of the Product and subject to the prior registration of your SCOTT
bike on www.scott-sports.com within 10 days as of the date of purchase. Transfer of
the Product from the first purchaser to another person terminates this limited warranty.
The limited warranty of five years for the frames and swingarms shall only be granted
in case once a year a maintenance service has been effected according to maintenance
requirements as set forth in the manual. The effected annual maintenance service shall
be confirmed by stamp and signature. In case such an annual maintenance service has
not been effected the warranty of five years for the frame shall be reduced to three years.
Costs for maintenance and service have to be borne by the owner of the Product.
On Gambler, Voltage FR and Volt-X the warranty period is limited to two years.
Repaired or replaced Products are covered for the remainder of the original warranty
period and subject to the conditions outlined in the original warranty, to the extent
permitted by law.
Hereby SCOTT grants a worldwide voluntarily manufacturer’s warranty. To the extent
permitted by law and unless a shorter duration is stipulated by law, any warranties implied
by law are limited in duration to maximum five, respectively two years, from the date of
purchase of the Product and are limited to the first purchaser of the Product.
What will SCOTT do in the event of a guarantee case?
SCOTT will replace the defective product with a product of a quality or nature and similar
level, will repair or refund the purchase price (after presentation of the proof of purchase of the
product), at its sole discretion. Non-defective components are replaced at your expense. In
such a case, we will contact you before replacing the non-defective part for your agreement.
What does this limited warranty not cover?
This limited warranty does not cover defects which did not exist before the transfer of
risks. This limited warranty does not cover Products used in rental operations. This limited
warranty does not cover purchases of not completely assembled bikes. This limited warranty
does not cover any defect caused by “wear and tear” (a complete list of all parts of “wear
and tear” can be found in the general manual that came with your bike), accident, neglect,
improper handling, colour fade due to exposure to sunlight, abuse, misuse, an act of God,
improper assembly, non-compliance with recommended maintenance and care procedures,
GUARANTEE ON SCOTT BIKES
17 |
BIKE USER MANUAL | SCALESCALE | BIKE USER MANUAL
| 16