Sealey AK716.V2 User manual

12PC BLIND BEARING PULLER SET
MODEL NO: AK716.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGEAND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this tool.
WARNING! Familiarise yourself with the specic applications and limitations of the kit, as well as any potential hazards.
9This kit should be used in conjunction with inspection maintenance procedures recommended in the vehicle manufacturer’s manual.
9Ensure that the kit is correct for the task.
9Wear the appropriate personal protective equipment for the task. A full range is available from your Sealey stockist.
8DO NOT use the kit for any purpose other than that for which it is designed.
9Ensure that the vehicle is properly supported with axle stands before working under the vehicle.
9Ensure there is adequate lighting prior to using the kit. A range of inspection lamps are available from your Sealey stockist.
9Keep children and unauthorised persons away from the working area.
8DO NOT use the kit if any parts are damaged or missing, as this may cause failure and/or personal injury.
8DO NOT use the kit when you are tired, or under the inuence of alcohol, drugs or intoxicating medication.
9After use, store in a safe, dry childproof area.
2. INTRODUCTION
Medium stroke 1.5kg slide hammer with 395mm shaft and a screw-type bridge extractor. Gently removes blind bearings where the use of a
slide hammer may damage the surrounding material. Includes bearing extractor collets with internal capacity from 8-34mm.
3. SPECIFICATION
Model No:..............................................................AK716.V2
Collet Ø:
Ø8-9.5, 10-11.5, 12-13.5, 15-16, 17-18.5, 20-23, 24.5-27, 30-32, 32-34mm.
4. CONTENTS
AK716.V2 Issue 4 (3) 10/03/22
Original Language Version
© Jack Sealey Limited
Refer to
instructions Wear eye
protection Wear protective
gloves
No. Part no. Description
1 AK716.V2-01 Slide hammer
2 AK716.V2-02 Collet 20-23mm + drive pin 13mm (long)
3 AK716.V2-03 Collet 8-9.5mm + drive pin 13mm (short)
4 AK716.V2-04 Collet 10-11.5mm + drive pin 10mm
5 AK716.V2-05 Collet 12-13.5mm
6 AK716.V2-06 Collet 15-16mm
7 AK716.V2-07 Collet 17-18.5mm
8 AK716.V2-08 Collet 24.5-27mm
9 AK716.V2-09 Collet 30-32mm
10 AK716.V2-10 Collet 32-34mm
11 AK716.V2-10 Drive pin 13mm
12 AK716.V2-12 Puller assembly
13 AK716.V2-13 Drive pin 5mm

5. OPERATION
5.1. SLIDE HAMMER
5.1.1. Before using the required attachment disassemble and grease as shown in g.1. Reassemble. Collet to be fully inserted into the
bearing before attempting to pull the bearing.
5.1.2. Insert the attachment into the bearing, see g.2.
5.1.3. Hold the attachment with a spanner and wind the drive pin into the attachment with another spanner until the jaws open and grip the
bearing.
5.1.4. Screw the attachment/drive pin onto the slide hammer, see g.3.
5.1.5. Hold the bearing puller and slide the hammer towards the bearing and then quickly back to the other end of the shaft. Repeat until
the bearing has been removed.
5.1.6. Make sure the bearing is being pulled out evenly. If not remove the puller attachment and softly tap the bearing back in with a soft
faced mallet, until it is seated squarely. Then reattach the tool and pull the bearing out.
5.1.7. Release the bearing by undoing the drive pin from the attachment.
5.2. BRIDGE EXTRACTOR
5.2.1. Before using the required attachment disassemble and grease as shown in g.1. Collet to be fully inserted into the bearing before
attempting to pull the bearing.
5.2.2. Insert the attachment into the bearing.
5.2.3. Hold the attachment with a spanner and wind the drive pin into the attachment, with another spanner, until the jaws open and grip the
bearing.
5.2.4. Place the bridge extractor legs in the correct position over the bearing housing, tighten the cap head screws on the legs to hold them
in position.
5.2.5. Screw the bridge extractor’s hex screw into the attachment. Hold the attachment with a spanner and tighten.
5.2.6. Hold the long cap head screw still and wind the bearing out using the nut beneath.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our
technical team on [e-mail] or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
g.1 g.2
g.3 g.4
Original Language Version
© Jack Sealey Limited AK716.V2 Issue 4 (3) 10/03/22