
VIKING 2/3 TONNE JACKING BEAM WITH 1.5M
EXTENDING ARMS
MODEL NO’S: SJBEX2000S, SJBEX3000S
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURYAND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9Ensure the beam is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. Use
genuine parts only. The use of improper parts may be dangerous and will invalidate the warranty.
9Inspect the beam before each use. DO NOT use the beam if it is damaged, altered, modified, in poor condition, leaking hydraulic fluid, or
unstable due to missing parts.
8DO NOT alter or modify this beam, including the safety valve, in any way. DO NOT load the beam beyond its rated capacity. DO NOT
operate the beam if damaged.
8DO NOT allow untrained persons to operate the beam.
8DO NOT use the beam for purposes other than that for which it is intended.
9Before installing and using the product, please carefully read and fully understand the contents of these instructions, and make sure that
every operator of the product has read and understood the contents, and put the instruction in a safe place for future reference.
9The product can be used between -20°-50°C.
8DO NOT use for the lifting of persons.
9Use the beam only for its intended purpose.
9Consult the vehicle manufacturer for the correct lifting locations.
9Make sure the vehicle is in park and the handbrake is on before attempting to raise the vehicle.
9Only use the saddles provided with the jacking beam.
9Be sure setup is stable and secure before lifting. Be careful of pinch points.
9This is a lifting device only. Make sure the load is central on saddles before lifting.
9The beam can only be used to lift one end of the vehicle.
9Ensure that there are no persons or obstructions beneath the vehicle before lowering. Always lower load slowly and carefully.
9Please check the spillage of oil before use, if you notice a spillage of oil, stop using the product and repair immediately.
9If the product can not be lowered as wished, the vehicle must be secured by suitable means against unintended lowering. Get a new
suitable product, with which you can lift the vehicle, so that the defect product can repaired or removed and changed. If you are unsure,
please ask for professional help.
9The operator MUST watch the lifting device and the load during all movements.
8DO NOT work under the raised load until it is secured by suitable means.
9Product safety markings need to be inspected before use and be maintained in as new condition. Contact Sealey for replacements if
damaged.
9This product must be maintained and repaired in accordance with the manufacturers instructions. Such maintenance and repair shall be
carried out by qualied persons.
9This jacking beam is only to be mounted on lifts approved by the lift manufacturer for mounting of jacking beams. Be aware that not all
lifts are approved. Rated beam capacity must be max. 2/3 of vehicle lift capacity.
9Mount the jacking beam with adequate support arms on horizontal, parallel and solid rails and secure arms before use.
9Check before each lift, that the support arms are correctly placed on rail of lift or pit edge.
9Always lower the jacking beam to the nearest safety stop immediately - or use axle stands for support before working on vehicle.
8DO NOT overload, for instance due to sudden external overload can cause damage or failure of the jacking beam.
9During lifting make sure the that the saddles cannot slide.
9Gravity of load must always be placed centrally.
9The 2 extension arms must only be used simultaneously.
WARNING! Failure to heed these precautions may result in loss of load, damage to beam and/or personal injury.
2. INTRODUCTION
Jacking beam lifts load with compressed air. Fully certied and approved to comply with MOT requirements. Wide lift conguration meets MOT
recommendation for lifting on jacking point. This item is heavy. Extra assistance must be provided at the delivery point to help its safe delivery.
Refer to
instruction
manual
Wear eye
protection Wear protective
clothing Wear safety
footwear
Original Language Version
© Jack Sealey Limited SJBEX2000S, SJBEX3000S Issue:1 26/10/22