Sealey VSE5613 User manual

INSTRUCTIONS FOR:
REAR AXLE REMOVAL TOOL
SET - BMW (E36, E46) 3 SERIES
MODEL NO: VSE5613
1. SAFETY INSTRUCTIONS
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to
these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND
WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2.1 Introduction
Remove and install all three rear axle bushes on E36
and E46 BMW 3 Series. Features a variety of adaptors
and plates used in various combinations for extracting
and installing old/new bushes. Suitable for on-car opera-
tion. Presented in a carry-case with each part numbered
for simple selection.
2.2 Applications
BMW 3 Series: E36 1978-89, E46 1983-93
2. INTRODUCTION & APPLICATIONS
3. CONTENTS
VSE5613 - 1 - 120607
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
!WARNING! Ensure Health and Safety, local authority
and general workshop practice regulations are adhered to
when using tools.
"DO NOT use the kit if any parts are missing or
damaged.
"DO NOT use the subframe bush replacement tool
for any purpose other than that for which it is
designed.
#Maintain the tool components in good and clean
condition for best and safest performance.
#Ensure that a vehicle which has been jacked up is
adequately supported with axle stands.
#Wear approved eye protection. A full range of
personal safety equipment is available from your
Sealey dealer.
#Wear suitable clothing to avoid snagging. Do not
wear jewellery and tie back long hair.
#Keep children and other unauthorised persons
away from the working area.
#Ensure there is adequate lighting prior to using the
subframe bush replacement tool.
IMPORTANT: These instructions are provided as a
guide only. Always refer to the vehicle manufacturer’s
service instructions, or a proprietary manual, to
establish the current procedure and data.
01284 757500
01284 703534 [e-mail]
Sole UK Distributor
Sealey Group,
Bury St. Edmunds,Suffolk.
www.sealey.co.uk
Web
email
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
www.sealey.co.uk, email [e-mail] or phone [phone].
!WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all
possible conditions and situations that may occur. It must be understood that common sense and caution are
factors which cannot be built into this product, but must be applied by the operator.

E36 REAR AXLE E46 REAR AXLE
USE PART 1, 6, 7, 8 & 9
THE FIRST BUSH
EXTRACTION
1
789
6
USE PART 1, 6, 7, 10 & 11
THE FIRST BUSH
INSTALLATION
1
711 10
6
USE PART 1, 8, 12 &15
THE SECOND BUSH
EXTRACTION
1
15 812
USE PART 1, 13, 14 &15
THE SECOND BUSH
INSTALLATION
1
15 14 13
USE PART 1, 2, 3, 6 & 7
THE THIRD BUSH
EXTRACTION
1
67
2
3
USE PART 1, 4, 5, 6 & 7
THE THIRD BUSH
INSTALLATION
1
6
7
4
5
4. INSTRUCTIONS
12
34
56
78
ON CAR OPERATION
REAR CONTROL ARM BUSH E36/E46 USE A WOODEN BLOCK TO SUPPORT CONTROL
ARM, THEN REMOVE THE BRAKE CALLIPER.
USE VSE5613 TO REMOVE THE REAR CONTROL
ARM BUSH.
USE VSE5613 TOOL TO INSTALL THE NEW REAR
CONTROL ARM BUSH.
12
34