Seametrics iMAG 4700r User manual

Precision Flow Measurement
An ON
I CON Brand
Electrical
Quick Start Guide
AC Power w/Pulse (A1X/A2X)
for: iMAG 4700r / AG3000r
253.872.0284 seametrics.com
Wiring
Black (Line)
White (Neutral)
Green (Ground)
Black (R) -Remote Pwr: pn10
Red (R) +Remote Pwr: pn9
Green (C1) Pulse+: pn2
White (C1) Pulse-: pn1
Orange (R) Remote B: pn11
Blue (R) Remote A: pn12
Black (Internal): pn14
Red (Internal): pn15
C1
R
AC
Orange (R) Remote B: pn4
Blue (R) Remote A: pn5
R
Black (R) -Remote Pwr: pn2
Red (R) +Remote Pwr: pn1
C1 = power/output cable
AC = AC power cable
R = remote cable
Refer to the Mechanical Quick Start Guide or the complete instruction manual for details on mechanical installation.
Remote Meter Remote Display
Remote Display: Remove the 3 screws holding the display
assembly and remove it from the meter. Remove the 15 pin
screw connector from its bag. Install the wires through the
cable ports into the 15 pin screw connector in their respective
locations. Plug the 15 pin screw connector into its socket. Be
sure all pins align properly and that the connector has not
slipped to one side. Refer to the complete manual for further
details.
Remote Meter: Unscrew the user access lid and remove it.
Remove the 5 pin screw connector from its socket. Install the
wires through the cable port into the 5 pin screw connector in
their respective locations. Plug the 5 pin screw connector into its
socket. Refer to the complete manual for further details.
Plug the backup
battery cable into the
back of the display
assembly.
Be sure all pins align
properly and that the
connector has not slipped to
one side.
User access lid Front panel—do
not open
WARNING: Improper sealing of glands or cables will invalidate any warranty.
Remove plug & o-ring. Insert
cable gland/strain relief. Feed
cable through cable gland.
CRITICAL!
Torque cable gland sealing
nut to 22 in-lbs.
Clamp cable with strain relief
clips. Attach drain wire lug to
bracket post.
WARNING: BACKUP BATTERIES
ARE NOT INTENDED AS A
PRIMARY POWER SOURCE

LT-14296r2.0 20180515
5/15/18
Seametrics • 19026 72nd Avenue South • Kent, Washington 98032 • USA
(P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • seametrics.com
Electrical Quick Start Guide
AC Power w/Pulse (A1X/A2X)
for: iMAG 4700r/ AG3000r
Menu System
1.2345678
100
TOTAL
CU FT
X1000
RATE
GPM
T UNIT R UNIT SET PDAMP
SET 4SET 20 SET F EXIT
TOTAL = GALLONS
PRESS + TO SET TOTAL
UNITS FOR DISPLAY
T UNIT R UNIT SET PDAMP
SET 4SET 20 SET F EXIT
TOTAL:
PRESS TO CHANGE
GALLONS
FWD TOTAL
The HOME Screen displays ow volume, direction of the ow total and ow RATE
along with status conditions such as Empty Pipe. Two buttons below the LCD
display are used to access menu screens for viewing and changing meter setup
parameters.
These two buttons are light sensors which can detect when a nger is covering
them. Only three button touch actions are needed to control navigation
through the menus, settings changes and back to the home screen.
HORIZONTAL SCROLLING:
Tap right-hand button to
scroll horizontally through
menu tabs or move
horizontally within a tab
dialog when applicable.
TAP
SELECT: Tap left-hand button
to change a highlighted item
within a tab dialog.
TAP
ENTER/EXIT: Hold left
button while tapping right
button once to enter or exit
a tab dialog or to navigate
between the HOME and
other menu screens.
+
HOLD TAP
All menu screens consist of two rows of tabs surrounding a dialog box that lets
you view and change setup parameters. To enter the Menu System perform the
hold and tap sequence. +
HOLD TAP
T UNIT
View or change TOTAL
volume units
R UNIT
View or change ow
RATE units
Set P
View or change pulse
output scaling
DAMP
View or change # of
seconds for rolling
average.
(0=1 second,
1=2 seconds, etc.)
EXIT
Return to HOME
SCREEN or enter
SUBMENU
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
TOTAL = GALLONS
PRESS + TO SET TOTAL
UNITS FOR DISPLAY
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
FLOW RATE = GALLONS/MIN
PRESS + TO SET RATE
UNITS FOR DISPLAY
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
00001.0 GALLONS
PRESS + TO SET
GALLONS TOTALIZED PER
PULSE SENT OUT PULSE1
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
DAMPING = 1
PRESS + TO SET
DAMPING VALUE
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
PRESS + EXIT MENU
AND RETURN TO FLOW
DISPLAY
The EXIT tab in the MAIN MENU has a second function. If you
tap ve times, you will be redirected to a SUBMENU screen
from which you can access additional options.
INFO: Meter model, serial number, rmware version
Changing Settings