Seaside Casual Adirondack 017 User manual

Page 1
REV A
Seaside Casual Furniture | 11 Industrial Drive Coventry, RI 02816 | 800-809-3114 | [e-mail]
1PLEASE READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING.
Carefully remove contents from box. Make sure that all parts and hardware
are included using the Parts List below.
WARRANTY QUESTIONS OR COMMENTS PLEASE CALL TOLL FREE AT 1-800-809-3114
Part Code: 316-1/4-20-50B
50mm Connector Bolt
Part Code: 4MMALLEN
4mm Allen Wrench
Part Code: 316-8X1-3/4PFDS
1-3/4” Phillips Head Screw
Right Left
Back Assembly
x 1
Foot Rest
Left Right
Left Right
Rear Leg Set
Seat Assembly
Rear Stretcher
1 1/4” Phillips Head Screw
80mm Hex Lag
Nylon Dowel
1” Phillips Pan Head Screw
Seat Apron
Side Stretcher
Bungs
x 1 x 1 x 1 x 1
x 1
x 2
x 1
x 4
x 6
x 6 x 2 x 6
x 2
Part Code: 316-1/4-20-1PPMS
x 4
Part Code: 316-8X1-1/4PFDS
x 10
Adirondack
Balcony Chair
(017 Shell Back)
(024 Classic Back)
Arm Set Front Leg Set
Part Code: 316-1/4-10-80HL
x 1
ASSEMBLY INSTRUCTIONS
4mm Allen Wrench (included); #2 Phillips Head Screwdriver;
#3 Phillips Head Screwdriver.
Tools Required:
Actual Size Actual Size Actual Size
Actual Size Actual SizeActual Size
5/8“
x 2
3/8“

Page 2
REV A
2ATTACH LEGS TO ARM
ASSEMBLY
Insert right side
Front and Rear
Legs into thread-
ed inserts in Right
Arm assembly as
show n. Turn
clock-wise until
s n u g . C o nt i n ue t u r n in g u n t i l
legs are into aligned position with
threaded inserts towards radius side of
arm.
Repeat process for left side.
Align counter-
bored holes in
Seat Assembly
with threaded
inserts in Legs.
Attach using (5)
50mm Connect-
or Bolts. Do not over tighten.
Repeat process for other side.
Attach Rear
Stretcher to
Rear Legs us-
ing (2) Nylon
D o w e l s
placed into
the larger of
the holes in the Stretcher. Align with
holes in Rear Legs. Secure using (2)
80mm Hex Lags thru counter-bored
holes in Rear Legs. Plug holes with (2)
5/8” Bungs.
3ATTACH SEAT TO LEGS
5ATTACH REAR STRETCHER
TO REAR LEGS
Attach Foot Rest
to Front Legs us-
ing (4) 80mm
Hex Lags thru
coun t e r -bo r e d
holes in Front
Legs. Plug holes
with (4) 5/8”
Bungs.
4ATTACH FOOT REST TO
FRONT LEGS

Page 3
REV A
Align Back As-
sembly with
Arms and Seat.
Secure upper
yoke by insert-
ing (2) 1” Phil-
lips Pan Head
Machine Screws into threaded insert in
Arms using a #3 Phillips head screw-
driver. Screw in lower yoke thru counter
-sunk holes in bottom of seat supports
using (2) 1 3/4” Phillips Deck Screws.
TIGHTEN ALL CONNECTIONS. AVOID OVER TIGHTENING; DOING SO
CAN CAUSE DAMAGE TO THE PRODUCT.
Attach front and
r e a r S e a t
Aprons by in-
serting (4) 1
1/4” Phillips
Deck Screws in-
to front and rear
of seat supports. Plug holes with (4) 3/8”
Bungs.
ATTACH REAR STRETCHER
TO REAR LEGS
7ATTACH BACK ASSEMBLY
8ATTACH FRONT AND REAR
SEAT APRONS
9
Flip Assembly up-
side down. Align
Side Stretcher with
pockets in Front
and Rear Legs. Se-
cure using (2)
1 3/4” Phillips
Head Screws.
Repeat Process for other side.
6ATTACH SIDE STRETCHERS
TO FRONT AND REAR LEGS