Seaside Casual DEX 140 User manual

DEX Collection 140, 141, 142, 143 Rev A Page 1
Seaside Casual Furniture | 11 Industrial Drive Coventry, RI 02816 | 800-809-3114 | [e-mail]
1PLEASE READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING.
Carefully remove contents from box. Make sure that all parts and hardware
are included using the Parts List below.
WARRANTY QUESTIONS OR COMMENTS PLEASE CALL TOLL FREE AT 1-800-809-3114
Back Assembly
x 1
Left Front Leg Assembly
DEX Seating
(140 Armless)
(141 Left Arm)
(142 Right Arm)
(143 Club Chair)
x 1
Front Apron
ASSEMBLY INSTRUCTIONS
4mm Allen Wrench (included); #2 Phillips Head Screwdriver;
Rubber Mallet
Tools Required:
Seat Assembly
x 1
x 1
Rear Apron
Right Armed Side Assembly
Right Front Leg Assembly
143 x 1
142 x 0
141 x 1
140 x 0
143 x 0
142 x 1
141 x 0
140 x 1
Left Armless Side Assembly
143 x 0
142 x 0
141 x 1
140 x 1
Right Armless Side Assembly
143 x 1
142 x 1
141 x 0
140 x 0
143 x 1
142 x 0
141 x 1
140 x 0
Left Armed Side Assembly
143 x 1
142 x 1
141 x 0
140 x 0

DEX Collection 140, 141, 142, 143 Rev A Page 2
Align Front and Rear Apron (Rear
Apron has pocket for screw) as
shown. Secure using (6) 50mm Hex
Lags thru counter-bored holes in Legs
into pilot holes in Aprons. Secure Rear
Apron using (2) 1-3/4” Phillips Head
Screws thru pockets into Rear Legs.
Plug Holes with 5/8” taps®.
Align Front Leg Assembly with correspond-
ing Side Assembly as shown. Secure using
(2) 50mm Hex Lags thru counter-bores in
Side Assembly into pilot holes in Front Leg.
2ATTACH SIDE TO FRONT LEG ASSEMBLY (ARMED VERSIONS ONLY)
3ATTACH APRONS TO SIDE ASSEMBLIES
Part Code: 4MMALLEN
4mm Allen Wrench
x 1
Part Code: 316-8X3/4PPDS
3/4” Phillips Pan Head Screw
x 10
Actual Size
Actual Size
Part Code: 316-8X1-3/4PFDS
1-3/4” Phillips Head Screw
x 10
50mm Hex Lag
Part Code: 316-1/4-10-50HL
Actual Size
5/8” tap®
x 10
Actual Size
x 12 Part Code: 316-8X3/4PTS
Parts List Continued:

DEX Collection 140, 141, 142, 143 Rev A Page 3
Secure Seat Assembly using (8) 1-3/4”
Phillips Head Screws thru counter-bores
in Seat into Pilot holes in Side Assembly.
Then use (10) 3/4” Pan Head Screws
thru Aluminum into bottom of Seat Sup-
port.
5ATTACH SEAT ASSEMBLY
Attach rear of Arm to Back Assembly using
(1 per Arm) 50mm Hex Lag thru counter-
bore hole in rear of Back Assembly into pi-
lot hole in rear of Arm. Plug hole with 5/8”
tap®.
ATTACH REAR STRETCHER
TO REAR LEGS
6ATTACH ARMS TO BACK (ARMED VERSIONS ONLY)
Align Back Assembly as shown. Secure using (4)
50mm Hex Lags thru counter-bored holes in Side
Aprons thru pilot holes in Back. And thru counter-bores
in Back Assembly into pilot holes in Rear Legs. Plug
Holes in Back with 5/8” taps®.
4ATTACH BACK ASSEMBLY