Secutron MR-3318 User manual

MR-3318
LT-1202SEC Rev 0
/PWFNCFS 2018
Installation and Operation Manual
Fire Alarm Control Panel

i
Table of Contents
1.0 FCC Notice 1
1.1 Notice for all MR-3318 Series Built-in UDACTs Sold in the U.S.A. ................................ 1
1.2 FCC Notice ..................................................................................................................... 1
2.0 Introduction 3
2.1 The MR-3318 Addressable Fire Alarm Control Panel .................................................... 3
2.2 General Notes ................................................................................................................ 4
3.0 MR-3318 Overview 5
3.1 MR-3318 Fire Alarm Control Panel Model ...................................................................... 5
3.2 MR-3318 System Components ...................................................................................... 6
4.0 Installation 12
4.1 Mechanical Installation ................................................................................................... 12
4.2 Installation Tips ............................................................................................................... 13
4.3 Installing Adder Modules ................................................................................................ 13
5.0 Operation 18
5.1 Addressable/Analog Devices .......................................................................................... 18
5.2 Configurable Input Types ............................................................................................... 20
5.3 Output Types .................................................................................................................. 24
5.4 NAC Circuit Operation .................................................................................................... 26
5.5 Single Stage Operation .................................................................................................. 27
5.6 Evacuation Codes .......................................................................................................... 27
5.7 Positive Alarm Sequence ............................................................................................... 27
5.8 Remote Annunciator Operation ...................................................................................... 29
5.9 Dialer Operation ............................................................................................................. 31
5.10 Using the Operation Menu from the Control Panel ......................................................... 32
6.0 Indication & Controls 45
6.1 Indication and Controls ................................................................................................... 45
6.2 LCD Display .................................................................................................................... 45
6.3 Common LED Indicators and Control Buttons ................................................................ 47
7.0 Wiring 51
7.1 Wiring Tables .................................................................................................................. 51
7.2 Wire Routing ................................................................................................................... 53

ii
7.3 Addressable Loop Wiring ............................................................................................... 54
7.4 NAC Circuit Wiring ......................................................................................................... 55
7.5 Module and Devices Wiring ........................................................................................... 58
7.6 Power Supply Wiring ...................................................................................................... 61
7.7 System Checkout ........................................................................................................... 64
7.8 Troubleshooting .............................................................................................................64
8.0 Appendix A - Compatible Receivers 65
9.0 Appendix B - MR-3318 Series Compatible Devices 66
9.1 MR-3318 Compatible Horn/Strobes ............................................................................... 66
9.2 UL Listed Supported Non-Synchronous Horn/Strobes .................................................. 66
10.0 Appendix C - Manual Panel Configuration 67
11.0 Appendix D - Reporting 72
11.1 Ademco Contact-ID MR-3318 Series Event Codes ...................................................... 72
11.2 Security Industries Association SIA Format Protocol MR-3318 Series Event Codes .... 73
12.0 Appendix E - Specifications And Features 74
12.1 MR-3318 Fire Alarm Control Panel ................................................................................ 74
12.2 MR-3318 System Module and Annunciator Specifications ............................................ 75
13.0 Appendix F - Battery Calculations 76
14.0 Warranty and Warning Information 78

iii
List of Figures
Figure 1 Model MR-3318 Single Loop Fire Alarm Control Panel .................................................. 5
Figure 2 MR-3318 Mechanical Installation Instructions and Dimensions ..................................... 12
Figure 3 Main Board with all Modules Installed ............................................................................ 14
Figure 4 Port and Jumper Locations on Main Board .................................................................... 15
Figure 5 Installing the PR-300 Polarity Reversal and City Tie Module ......................................... 17
Figure 6 MR-3318 Configurator Date and Time Settings .............................................................. 19
Figure 7 Enabling the Positive Alarm Sequence ........................................................................... 29
Figure 8 Operation Menu ............................................................................................................. 32
Figure 9 LED Indicators and Control Buttons ............................................................................... 45
Figure 10 Numeric Keypad ............................................................................................................. 46
Figure 11 Wire Routing ................................................................................................................... 53
Figure 12 Addressable Loop Wiring - Class B or Style 4 ................................................................ 54
Figure 13 Addressable Loop Wiring - Class A or Style 6 ................................................................ 54
Figure 14 Addressable Loop Wiring - Class X or Style 7 ................................................................ 55
Figure 15 NAC Circuit – Class B or Style Y Wiring ......................................................................... 56
Figure 16 NAC Circuit – Class A or Style Z Wiring ......................................................................... 56
Figure 17 MR-2300T Common Remote Trouble Indicator Wiring .................................................. 57
Figure 18 Wiring the Dialer ............................................................................................................ 58
Figure 19 Connecting an FACP to a 3G4010CF Interface Device outside Canada ....................... 59
Figure 20 Wiring the PR-300 Polarity Reversal and City Tie Module ............................................. 60
Figure 21 Main Power Supply Wiring and Connections .................................................................. 62
Figure 22 Supervision of Auxiliary Supplies ....................................................................................63

iv
List of Tables
Table 1 MR-3318 System Components ...................................................................................... 6
Table 2 Advanced Protocol Detectors ......................................................................................... 9
Table 3 Advanced Protocol Intelligent Modules .......................................................................... 9
Table 4 Advanced Protocol Manual Stations .............................................................................. 10
Table 5 Ancillary Modules ........................................................................................................... 10
Table 6 Bases ............................................................................................................................. 10
Table 7 CLIP Detectors ............................................................................................................... 10
Table 8 CLIP Modules ................................................................................................................. 11
Table 9 Main Board Connectors and Jumper ............................................................................. 16
Table 10 PR-300 Polarity Reversal and City Tie Module Connectors and Jumpers ..................... 17
Table 11 UL864 90.23 Table ......................................................................................................... 18
Table 12 Configurable Input Types ............................................................................................... 20
Table 13 Configurable Output Types ............................................................................................ 25
Table 14 Annunciator Address DIP Switch Settings ..................................................................... 30
Table 15 List Bypass Special Characters ..................................................................................... 41
Table 16 Keypad and Cursor buttons descriptions ....................................................................... 46
Table 17 LED Indicators and Control Buttons ............................................................................... 47
Table 18 Advanced Protocol and CLIP Devices Addressable Loop Wiring Table ........................ 51
Table 19 NAC and Auxiliary Power Circuits Wiring Table ............................................................. 51
Table 20 MRI-502MAP(A) Conventional Zone Module Input Circuit Wiring Table ....................... 52
Table 21 Power Supply Electrical Ratings .................................................................................... 61
Table 22 Compatible DACR Receivers ......................................................................................... 65
Table 23 MR-3318 Compatible Horn/Strobes ............................................................................... 66
Table 24 Contact-ID Event Codes ................................................................................................72
Table 25 SIA-DCS Event Codes ...................................................................................................73
Table 26 MR-3318 Specifications ................................................................................................. 74
Table 27 MR-3318 System Modules and Annunciator Specifications .......................................... 75
Table 28 Recommended Batteries ................................................................................................ 77

1
1.0 FCC Notice
.
1.1 Notice for all MR-3318 Series Built-in UDACTs Sold in the
U.S.A.
Secutron's MR-3318 SERIES BUILT-IN UDACT Digital Communicator described in this
manual is listed by Underwriters Laboratories Inc. (ULI) for use in slave application in
conjunction with a Listed Fire Alarm Control Panel under Standard 864 (Control Units for Fire
Protective Signalling Systems). These Communicators comply with the National Fire
Protection Association (NFPA) performance requirements for UDACTs and should be installed
in accordance with NFPA 72 Chapter 4 (Supervising Station Fire Alarm System). These
Communicators should be installed in accordance with this manual; the National Electrical
Code (NFPA 70); and/or the local Authority Having Jurisdiction (AHJ).
1.2 FCC Notice
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
ACTA. On the telco transformer of this equipment is a label that contains, among other
information, a product identifier in the format US:1M8AL01BFX33318. If requested, this
number must be provided to the telephone company. This equipment is capable of seizing the
line. This capability is provided in the hardware.
Type of Service
The Communicator is designed to be used on standard device telephone lines. It connects to
the telephone line by means of a standard jack called the USOC RJ-11C (or USOC FJ45S).
Connection to telephone company provided coin service (central office implemented systems)
is prohibited. Connection to party lines service is subject to state tariffs.
Telephone Company Procedures
The goal of the telephone company is to provide you with the best service it can. In order to do
this, it may occasionally be necessary for them to make changes in their equipment,
Attention: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or
electrician, as appropriate.
Notes: The Ringer Equivalence Number (REN) assigned to each terminal device
provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may consist
of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all the devices does not exceed 5.
The Label Identification Number for this product is US:1M8AL01BFX3318. The
01B represents the REN without a decimal point (for example, 01B is a REN of
0.1B).
!
i

2
operations or procedures. If these changes might affect your service or the operation of your
equipment, the telephone company will give you notice, in writing, to allow you to make any
changes necessary to maintain uninterrupted service. In certain circumstances, it may be
necessary for the telephone company to request information from you concerning the
equipment which you have connected to your telephone line. Upon request of the telephone
company, provide the FCC registration number and the ringer equivalence number (REN);
both of these items are listed on the equipment label. The sum of all of the REN’s on your
telephone lines should be less than five in order to assure proper service from the telephone
company. In some cases, a sum of five may not be usable on a given line.
If Problems Arise
If any of your telephone equipment is not operating properly, you should immediately remove it
from your telephone line, as it may cause harm to the telephone network. If the telephone
company notes a problem, they may temporarily discontinue service. When practical, they will
notify you in advance of this disconnection. If advance notice is not feasible, you will be
notified as soon as possible. When you are notified, you will be given the opportunity to correct
the problem and informed of your right to file a complaint with the FCC. Contact your
telephone company if you have any questions about your phone line. In the event repairs are
ever needed on the Communicator, they should be performed by Mircom Technologies Ltd. or
an authorized representative of Mircom Technologies Ltd. For information contact Mircom
Technologies Ltd. at the address and phone numbers shown on the back page of this
document.

3
2.0 Introduction
This document provides information for the successful installation and operation of the MR-
3318.
2.1 The MR-3318 Addressable Fire Alarm Control Panel
Secutron’s MR-3318 Addressable Fire Alarm Control Panel provides the following:
• Advanced Protocol mode with one loop with 159 addressable sensors and 159
addressable modules per loop.
• CLIP Device compatible.
• Four Power Limited Class B (Style Y) or Class A (Style Z) NAC circuits.
• NAC circuits may be configured as silenceable signal, non-silenceable signal,
silenceable strobes, non-silenceable strobes, or relay output. The audible signal may be
Steady, Temporal Code, California Code, or March Time.
• Supports sync strobe protocols from major manufacturers.
• Software configuration.
• Alarm verification, waterflow retard and positive alarm sequence operations.
• Configurable Signal Silence Inhibit, Auto Signal Silence, Two-Stage Operation, and
One-Man Walk Test.
• Subsequent Alarm, Supervisory, Monitor and Trouble operation.
• Relay Contacts for Common Alarm, Common Supervisory and Common Trouble all
non-disconnectable and Auxiliary Alarm Relay (disconnectable).
• Built-in Dialer Module.
2.1.1 Optional Items
• Semi-flush or surface mountable enclosure for retrofits and new installations.

4
2.2 General Notes
Circuits
Refers to a physical electrical interface for the analog loop, indicating signals or relays, and
common alarm, supervisory, and trouble relay outputs.
Zone/Group
Is a logical concept for a Fire Alarm Protected Area, and will consist of at least one Circuit. The
MR-3318 uses Groups extensively to facilitate annunciation of multiple input and output points
on the 30 (up to 64) LED display and to facilitate the bypassing of inputs and outputs.
Display Points
The MR-3318 LCD display annunciates the status of the system and connected devices.
Wiring Styles
The analog loop can be connected in Class B (Style 4), Class A (Style 6), or Class X (Style 7)
configurations.

5
3.0 MR-3318 Overview
This chapter lists all the possible components of an MR-3318 system.
3.1 MR-3318 Fire Alarm Control Panel Model
The MR-3318 Fire Alarm Control Panel has the following features:
• Main Board, Power Supply and Backbox.
• Multi-zone fire alarm control panel.
• Main Display with 4 x 20 LCD display.
• Class A (Style 6), Class X (Style 7), or Class B (Style 4) analog loop.
• Four Power Limited Class B (Style Y) or Class A (Style Z) NAC circuits (max 1.5 Amps
each - 5.0 Amps total).
• Dedicated common alarm, supervisory, trouble, and auxiliary alarm relays.
• Additional outputs include connections for a RTI remote trouble indicator, PR-300
Reverse Polarity Module, an RS-485 bus for connection of up to seven RAX-LCD-LITE,
RAM-3318-LCDs, MR-2312-SR(W)12s and RA-1000 Series annunciators.
• Auxiliary power is available in the form of 24V FWR unfiltered and unsupervised, 24VDC
filtered and regulated, and resettable auxiliary power supply.
Figure 1 Model MR-3318 Single Loop Fire Alarm Control Panel

6
3.2 MR-3318 System Components
The following table describes the components of the MR-3318.
Table 1 MR-3318 System Components
Model Description
MR-3318 Black backbox, red door enclosure comes complete with main board, power supply, transformer and
main display.
RAM-3318-LCD Remote Annunciator with 4-line LCD Display.
PR-300 Polarity Reversal and City Tie Module.
PCS-100 Power Supply Interface Board use for powering 3G4010CF Universal Wireless Alarm
Communicator.
3318

7
MR-2312-SW12 Smart Relay Module with White Enclosure.
Can support up to 12 relays.
MR-2312-SR12 Smart Relay Module with Red Enclosure.
Can support up to 12 relays.
RAM-1016TZDS 16 Point Annunciator Chassis with 16 Trouble
LEDs.
RAM-1032TZDS 32 point Remote Annunciator with 32 Trouble LEDs.
MGD-32 Graphic Annunciator.
RAX-LCD-LITE Remote Annunciator with 4-line LCD Display.
Table 1 MR-3318 System Components (Continued)
Model Description

8
AGD-048 Graphic Annunciator Adder Driver Board.
MR-2300T Common Remote Trouble Indicator, Buzzer and
LED.
MMX-BB-1001D
MMX-BB-1001DR
White Enclosure for one annunciator.
Red Enclosure for one annunciator.
MMX-BB-1002D
MMX-BB-1002DR
White Enclosure for two annunciators.
Red Enclosure for two annunciators.
MMX-BB-1003D
MMX-BB-1003DR
White Enclosure for three annunciators.
Red Enclosure for three annunciators.
MP-300 End of line resistor plate. 3K9.
Table 1 MR-3318 System Components (Continued)
Model Description

9
3.2.1 Devices
The following tables lists all the devices available for the MR-3318.
Table 2 Advanced Protocol Detectors
Advanced Protocol Detectors
MRI-1251AP Advanced Protocol Ion Smoke Detector
MRI-2251AP Advanced Protocol Photo Smoke Detector
MRI-2251TAP Advanced Protocol Photo Heat Detector
MRI-2251TMAP Advanced Protocol Acclimate Detector
MRI-5251AP Advanced Protocol Heat Detector
MRI-5251HAP Advanced Protocol High Temperature Heat Detector
MRI-5251RAP Advanced Protocol Rate of Rise Heat Detector
Table 3 Advanced Protocol Intelligent Modules
Advanced Protocol Intelligent Modules
MRI-M500MAP Advanced Protocol Monitor Module
MRI-M500RAP Advanced Protocol Relay Control Module
MRI-M500SAP Advanced Protocol Supervised Control Module
MRI-M501MAP Advanced Protocol Mini Monitor Module
MRI-M502MAP Advanced Protocol Conventional Zone Module

10
Table 4 Advanced Protocol Manual Stations
Advanced Protocol Manual Stations
MRM-701APU Addressable Single Stage Single Action Station
MRM-710APU Addressable Single Stage Dual Action Station
Table 5 Ancillary Modules
Ancillary Modules
CR-6 Six Relay Control Module
CZ-6 Six Conventional Zone Interface Module
IM-10 Ten Input Monitor Module
MRI-M500X Fault Isolator Module
SC-6 Six Supervised Control Module
Table 6 Bases
Bases
B210LP Intelligent Flanged Mounting Base
B224BI Intelligent Isolator Base
B224RB Intelligent Relay Base
B501 Intelligent Flangeless Mounting Base
DNR Intelligent non-relay photoelectric low-flow duct smoke detector housing
DNRW Watertight Intelligent Non-relay Photoelectric Low-flow Duct Smoke Detector
Housing
Table 7 CLIP Detectors
Intelligent Detectors
MRI-1251B Intelligent Low Profile Ionization Smoke Sensor
MRI-2251B Intelligent Low Profile Photoelectronic Smoke Sensor
MRI-2251TB Intelligent Low Profile Photoelectronic Smoke Sensor c/w 135°F Fixed Temp.
Thermal Sensor
MRI-2251TMB Intelligent Low Profile Multi-Criteria Sensor
MRI-5251B Intelligent Low Profile Fixed Temp. Thermal Sensor 135°F
MRI-5251H Intelligent Low Profile High Temperature Thermal Sensor 190°F
MRI-5251RB Intelligent Low Profile Fixed Temp. and Rate of Rise Thermal Sensor 135°F
MRI-7251B Intelligent Low Profile Laser Smoke Detector

11
Table 8 CLIP Modules
Intelligent Modules
MRI-500DM Intelligent Dual Monitor Module
MRI-M500M Intelligent Addressable Monitor Module
MRI-M500R Intelligent Addressable Relay Module
MRI-M500S Intelligent Addressable Supervised Control Module
MRI-M501M Intelligent Addressable Mini-Monitor Module
MRI-M502M Intelligent Addressable Interface Module

12
4.0 Installation
This chapter describes the installation of the MR-3318.
4.1 Mechanical Installation
The MR-3318 is suitable for flush or surface mounting with a built-in trim ring.
Figure 2 MR-3318 Mechanical Installation Instructions and Dimensions
Dimensions of Enclosure (minus built in trim ring) 14.5” x 4.25” x 21”
Distance between horizontal mounting screws 12”
Distance between vertical mounting screws 18.9”
Complete Dimensions of Enclosures 16.7” x 5.7” x 23”
5.70
12.00
12.00
18.90
14.50
5.75
21.14
1.51 16.28
16.71
22.92

13
4.2 Installation Tips
1. Group the incoming wires through the top of the enclosure. For easy identification and
neatness use a wire tie to group wires.
2. Be sure to connect a solid Earth Ground (from building system ground / to a cold water
pipe) to the Chassis Earth Ground Mounting Lug, and to connect the Earth Ground Wire
Lugs from the Main Chassis to the ground screw on the backbox.
4.3 Installing Adder Modules
The MR-3318 Fire Alarm panel is shipped pre-assembled with all main components and
boards.
The following items can be installed in the field:
• PR-300 Polarity Reversal And City Tie Module
• PCS-100 Power Supply Interface Board
See the following diagrams for adder module installation locations. For Jumper or DIP Switch
settings refer to Table 9 and for Wiring Specifications see 7.1 Wiring Tables.
Attention: DO NOT install cable through bottom of the box. This space is reserved
for Batteries.
!

14
Figure 3 Main Board with all Modules Installed
MD-819 Power Supply Board
PR-300 Polarity Reversal
And City Tie Module
MR-3318 Main Board
TR-061Transformer
Barrier Terminal Block
Note:
The PCS-100 mounts in the same
position as the PR-300. Only one
module may be used.
PR-300 or PCS-100 mounts
on the right-hand side
inside the backbox