See Water WS Series Setup guide

Panel Installation:
1. Caution: To maintain the NEMA 4X rating, make
all wiring connections with seal tight cable grips
or conduit connections.
2. Determine mounting location for control panel.
Mount panel using mounting feet supplied.
3. The control panel should not be mounted in
an area that is subject to submersion.
4. Run pump cables and oat cables through
conduit. Make eld connections as shown on
wiring diagram.
5. Run power line conductor through conduit. Wire
to terminals per enclosed schematic. Branch
circuit protection to be provided by installer.
6. Connect power conductors 208/240/480V to
proper locations on terminal block.
7. Float cables require separate conduit from
power and pump cables.
8. Mount oat switches at appropriate levels. Be
sure that the oats have a free range of motion
to prevent entanglement.
Start up:
1. When the power is applied, the green power
light located on the white front swing panel shall
light.
2. The pump HOA switches shall be placed to the
Auto position to ensure the pump will turn on
from the commands of the oats. The pump
can be tested or turned on manually if the HOA
switch is held in the Hand (Manual) position.
To test the alarm circuit, push the test button on the
front panel, the audible alarm shall sound and the
red beacon will light. Press the silence button to
silence the alarm.
Three Phase Triplex Control Panel
Installation and Operator’s Manual
WS Series® Triplex Control Panel
The WS Series® Triplex control panels will control three
pumps in sewage, wastewater, and dewatering applications.
All panels are UL listed for the United States and Canada and
come with a three year warranty.
Models (Ratings):
WT3P-6-1 (1.0-1.6 pump full load amps)
WT3P-6-2 (1.6-2.5 pump full load amps)
WT3P-6-3 (2.5-4.0 pump full load amps)
WT3P-6-4 (4.0-6.3 pump full load amps)
WT3P-6-5 (6.0-10.0 pump full load amps)
WT3P-6-6 (9.0-14.0 pump full load amps)
WT3P-6-7 (13.0-18.0 pump full load amps)
WT3P-6-8 (17.0 -23.0 pump full load amps)
WT3P-6-9 (20.0-25.0 pump full load amps)
WT3P-6-10 (24.0-32.0 pump full load amps)
Features:
• Designed to control three 208/240/480VAC pumps in
sewage applications
• NEMA 4X polycarbonate enclosure with stainless steel
lockable latches
• Pump control visible features: pump hand-o󰀨-auto
(H.O.A.) switches for pump #1, 2 and 3, green pump run
lights, red pump fault lights with reset button and green
power on light
• Alarm visible features: red beacon alarm light, alarm test
and silence buttons
• Alarm horn sounds at 85 decibels at 10’
• Remote monitoring dry contacts: low liquid, high liquid,
pump #1 fault, pump #2 fault, pump #3 fault, pump #1 run,
pump #2 run, pump #3 run (normally open)
• Pump protection: motor protective switch included for all
pumps (branch circuit protection, adjustable overload and
disconnect), pump thermal cutout circuit
• Includes 6 oats. 5 narrow angle N/O oat switches with
20′ cords and mounting hardware and 1 low level narrow
angle N/C oat switch with 20’ cord
• Float status indicators (low level, stop, lead, lag, lag/lag,
and high liquid)
• UL Listed for the United States and Canada
www.seewaterinc.com
951.487.8073 • 888.733.9283
Email: [e-mail]
121 North Dillon Avenue • San Jacinto, CA 92583
P.O. Box 1269 • San Jacinto, CA 92581
IM 411 Rev. 0417
1. All installations must be in accordance with the National Electrical
Code, and any other applicable state and local electrical
requirements.

Three Phase Triplex Control Panel
www.seewaterinc.com
951.487.8073 • 888.733.9283 • Email: [email protected]
121 North Dillon Avenue • San Jacinto, CA 92583
P.O. Box 1269 • San Jacinto, CA 92581
Additional Panel Options:
SF - Seal Failure Circuit (optional)
The seal fail circuit will indicate when there is water in the
pump chamber. The circuit is setup to work with a variety of
pumps with a range of resistance sensitivity settings.
AF - Alarm Flasher
ET - Elapsed Timer Meter w/ LCD display & reset
CC - Cycle Counter w/LCD display & reset
LA - Lightning Secondary Surge Arrestor
Service:
Caution: Before checking electrical connections within
the control or attempting to replace any components, turn
o all branch circuits supplying power to the main control
panel.
Troubleshooting:
Alarm Circuit
To test the alarm light and buzzer, press the test button on the
front panel. If either the light or buzzer do not indicate, replace
the light bulb or buzzer with same type.
Control Board and Fuse
If the power on light is not illuminating on the front panel,
check the voltage at TS1-1 and TS1-2 with a voltage meter.
The voltage should read 120VAC. If voltage present, check
the fuse in the fuse block. If fuse is blown, replace fuse with
same type. The dry contacts are rated for 125VDC, 5 amp
maximum.
Floats
The control board has LED Indicators that will illuminate
when the oats are in the open position. Check oats for
entanglement, full range of motion. Replace damaged oats.
For additional information regarding
operation and troubleshooting questions,
please call See Water, Inc. at 888-733-9283.
Typical Installation for Triplex Control Panel
A typical pump installation showing (1) Control panel,
(2) high liquid alarm oat, (3) lag/lag pump oat, (4)
lag pump oat, (5) lead pump oat, (6) stop oat,
(7) low level oat, (8) pump #1, (9) pump #2 and
(10) pump #3. All pump cords are connected to the
wastewater control panel.
1
1098
2
3
4
5
6
7