Seeley CP15HW1 User manual

(English) (CP15HW1)
CP15HW1
®
OWNER’S MANUAL
Portable Reverse Cycle Air Conditioner

Please read these instructions prior to using the appliance and
save them for future reference.
Waste electrical products must not be disposed of with household
waste. This product should be taken to your local recycling centre for
safe treatment.
CONTENTS
Introduction......................................1
Safety ..............................................2
Component location.........................3
Install .......................................4ation
Control panel ...............5and Display
Remote control ................................6
Operation......................................7-8
Maintenance ....................................9
Troubleshooting .............................10
Specifications.................................11
Warranty ........................................12
iCP15HW1 Portable Reverse Cycle Air Conditioner
THANK YOU for choosing a Convair
Air Conditioner. This appliance has
been carefully engineered to bring you
trouble-free personal air conditioning.
Please read this manual carefully so
that you take full advantage of thecan
many benefits your Convair provides.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have supervision or been
given instruction in using the appliance by
a person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
Do not place anything through the
ventilating slots.
Be sure the appliance has been securely
and correctly installed according to the
installation instructions contained within
this manual.
Personal Cooling and Heating
Your Convair Reverse Cycle Air
Conditioner is a portable unit that supplies
refrigerated air to a personaland heating
area within a room. It is not intended to
function as a house or room air
conditioner.
Energy Saving Tips
lDo not locate the air conditioner where
furniture or other objects can obstruct
the air flow.
lKeep curtains and blinds closed during
the hottest part of the day.
lKeep the filters clean.
lSet the air conditioner to maximum
cooling and high fan speed initially,
then adjust to a comfortable setting.
lDo not wait until the room is
excessively hot before using the air
conditioner.
Warranty
Convair air conditioners are warranted
against faulty manufacture for 2 years after
purchase. Please refer to page 12 for more
details on warranty.
INTRODUCTION
1
SEELEY INTERNATIONAL – OWNER’S MANUAL

Please read these instructions prior to using the appliance and
save them for future reference.
Waste electrical products must not be disposed of with household
waste. This product should be taken to your local recycling centre for
safe treatment.
CONTENTS
Introduction......................................1
Safety ..............................................2
Component location.........................3
Install .......................................4ation
Control panel ...............5and Display
Remote control ................................6
Operation......................................7-8
Maintenance ....................................9
Troubleshooting .............................10
Specifications.................................11
Warranty ........................................12
iCP15HW1 Portable Reverse Cycle Air Conditioner
THANK YOU for choosing a Convair
Air Conditioner. This appliance has
been carefully engineered to bring you
trouble-free personal air conditioning.
Please read this manual carefully so
that you take full advantage of thecan
many benefits your Convair provides.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have supervision or been
given instruction in using the appliance by
a person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
Do not place anything through the
ventilating slots.
Be sure the appliance has been securely
and correctly installed according to the
installation instructions contained within
this manual.
Personal Cooling and Heating
Your Convair Reverse Cycle Air
Conditioner is a portable unit that supplies
refrigerated air to a personaland heating
area within a room. It is not intended to
function as a house or room air
conditioner.
Energy Saving Tips
lDo not locate the air conditioner where
furniture or other objects can obstruct
the air flow.
lKeep curtains and blinds closed during
the hottest part of the day.
lKeep the filters clean.
lSet the air conditioner to maximum
cooling and high fan speed initially,
then adjust to a comfortable setting.
lDo not wait until the room is
excessively hot before using the air
conditioner.
Warranty
Convair air conditioners are warranted
against faulty manufacture for 2 years after
purchase. Please refer to page 12 for more
details on warranty.
INTRODUCTION
1
SEELEY INTERNATIONAL – OWNER’S MANUAL

SAFETY
For indoor use only.
Transport the air conditioner in an upright
position only, or leave it in an upright position
for at least 2 hours before use (Fig 1).
Use only in the upright position on a flat level
surface and at least 50cm from any objects.
Do not place objects on the air conditioner, or
through the ventilating slots or restrict the air
inlets & outlets (Fig 2).
Closely supervise any children and pets
when the air conditioner is in use.
Do not store or operate the appliance near
any flammable substances.
During operation, water will collect in the
bottom tank of the air conditioner. Be careful
when moving the unit to prevent water from
spilling.
Electrical Safety
Ensure the appliance has been installed in
accordance with national wiring regulations.
Electrical Safety (cont)
Caution! before connecting the
electrical power cord to a power outlet,
check that the air conditioner voltage
is the same as your power supply (refer
to the rating label located on the side of
the unit - refer Fig 4). Ensure the power
supply is correctly earthed and rated.
Plug the air conditioner directly into a
properly installed power outlet. Never use
an extension cord, double adaptor or multi
power outlet board to run this air
conditioner.
Do not pull the unit along by the power
cord or place the power cord near a
source of heat. Always unroll the power
cord completely before use.
If the power supply cord is damaged it
must be replaced by the manufacturer, a
service agent or similarly qualified
persons in order to avoid a hazard.
Switch off and unplug when not in use.
Do not use in humid environments such
as bathrooms, laundries or other steamy
or wet areas.
Do not touch or operate the air
conditioner with wet or damp hands or
when standing barefoot.
2
1
2CP15HW1 Portable Reverse Cycle Air Conditioner
4
3
Remote
Control
Air Outlet
Display Panel
Vane Adjustment slider
Drain Pump
Connector
Handle
Control
Panel
Exhaust Hose
Hose End
Window Attachment
(2 pieces)
Exhaust Nozzle
(window end)
COMPONENT LOCATION
3
SEELEY INTERNATIONAL –OWNER’S MANUAL
Drain
Evaporator
Air Intake
Power
Cord
Exhaust Air
Outlet
Rating Label
Cord Storage
IntakeAir
ON/OFF
SPEED
TIMER
MODE
UP
DOWN
+
Drain pump
outlet

SAFETY
For indoor use only.
Transport the air conditioner in an upright
position only, or leave it in an upright position
for at least 2 hours before use (Fig 1).
Use only in the upright position on a flat level
surface and at least 50cm from any objects.
Do not place objects on the air conditioner, or
through the ventilating slots or restrict the air
inlets & outlets (Fig 2).
Closely supervise any children and pets
when the air conditioner is in use.
Do not store or operate the appliance near
any flammable substances.
During operation, water will collect in the
bottom tank of the air conditioner. Be careful
when moving the unit to prevent water from
spilling.
Electrical Safety
Ensure the appliance has been installed in
accordance with national wiring regulations.
Electrical Safety (cont)
Caution! before connecting the
electrical power cord to a power outlet,
check that the air conditioner voltage
is the same as your power supply (refer
to the rating label located on the side of
the unit - refer Fig 4). Ensure the power
supply is correctly earthed and rated.
Plug the air conditioner directly into a
properly installed power outlet. Never use
an extension cord, double adaptor or multi
power outlet board to run this air
conditioner.
Do not pull the unit along by the power
cord or place the power cord near a
source of heat. Always unroll the power
cord completely before use.
If the power supply cord is damaged it
must be replaced by the manufacturer, a
service agent or similarly qualified
persons in order to avoid a hazard.
Switch off and unplug when not in use.
Do not use in humid environments such
as bathrooms, laundries or other steamy
or wet areas.
Do not touch or operate the air
conditioner with wet or damp hands or
when standing barefoot.
2
1
2CP15HW1 Portable Reverse Cycle Air Conditioner
4
3
Remote
Control
Air Outlet
Display Panel
Vane Adjustment slider
Drain Pump
Connector
Handle
Control
Panel
Exhaust Hose
Hose End
Window Attachment
(2 pieces)
Exhaust Nozzle
(window end)
COMPONENT LOCATION
3
SEELEY INTERNATIONAL –OWNER’S MANUAL
Drain
Evaporator
Air Intake
Power
Cord
Exhaust Air
Outlet
Rating Label
Cord Storage
IntakeAir
ON/OFF
SPEED
TIMER
MODE
UP
DOWN
+
Drain pump
outlet

INSTALLING THE EXHAUST HOSE
Step 1: Push the Hose End onto the cooler,
and rotate so the slot locks onto the catch
(Fig 5). F Hoseit the exhaust hose to the
End and Hose Exhaust Nozzle by turning
clockwise.
Step 2: Open a indow and fit the Windoww
K Extend the attachment as required andit. s
lock into place with the w provided.ingnuts
Ensure the outlet is not obscured. The
Window K can be installed horizontally orit
vertically, t window type.o suit your Fit the
Exhaust Nozzle to the Window Kit, and lock
into place (Fig 7A & 7B ).
INSTALLING THE DRAIN PUMP HOSE
Step 1. Connect the Drain Pump Connector
to the drain hole on the rear panel (Fig 6).
Push firmly to lock into place.
Step 2. Connect the supplied water hose to
the Drain Pump Connector (Fig 6).
Step 3. Lead the other end of the hose
through the hole in the Window Kit to the
outside or to a suitable location for drainage
i.e. a drain or sink.
Note! The minimum distance required
from the operating air conditioner to
any obstructing objects or walls is
50cm.
Keep the exhaust hose as short and
straight as possible and minimise
kinks. This will maximise the cooling
performance.
Don’t use extension pieces for the
exhaust pipe as this will reduce
performance and possibly result in
damage to the air conditioner.
Hot air and possibly mist will be
emitted from the exhaust hose.
Note! It is critical to the performance of
the unit that the hot exhaust air is
completely removed from the space
being cooled.
4CP15HW1 Portable Reverse Cycle Air Conditioner
To avoid damage to the control panel, do not operate with sharp objects.
NOTE!
8
CONTROL PANELAND DISPLAY
5
SEELEY INTERNATIONAL –OWNER’S MANUAL
7A
6
5
Press to turn the air
conditioner on and off
Press to cycle the fan
speed between low,
medium and high
Press to enter the
timer setting mode
and time
Press to cycle from
Cooling, Dehumidifying
and HeatingFan
Modes
Press to increase,
to decrease the
set temperature
In Timer mode, press
to increase, to
decrease the timer
from 01-24 hours
In Cooling mode, press
at same time to toggle
between °C and °F
Power ON / OFF
button
Fan Speed
control button
Timer Set
button
Mode Select
button
Set
Temperature
and Timer
Display
Remote
Control
Receiver
Fan Speed
Indicator Lights
Low - 1 Light
Medium - 2 Lights
High - 3 Lights
Mode
Indicator
Light
Blue - Cooling
Yellow - Dehumidify
Green - Fan
Red - Heating
Water Full
Indicator
Timer
Indicator
7B

INSTALLING THE EXHAUST HOSE
Step 1: Push the Hose End onto the cooler,
and rotate so the slot locks onto the catch
(Fig 5). F Hoseit the exhaust hose to the
End and Hose Exhaust Nozzle by turning
clockwise.
Step 2: Open a indow and fit the Windoww
K Extend the attachment as required andit. s
lock into place with the w provided.ingnuts
Ensure the outlet is not obscured. The
Window K can be installed horizontally orit
vertically, t window type.o suit your Fit the
Exhaust Nozzle to the Window Kit, and lock
into place (Fig 7A & 7B ).
INSTALLING THE DRAIN PUMP HOSE
Step 1. Connect the Drain Pump Connector
to the drain hole on the rear panel (Fig 6).
Push firmly to lock into place.
Step 2. Connect the supplied water hose to
the Drain Pump Connector (Fig 6).
Step 3. Lead the other end of the hose
through the hole in the Window Kit to the
outside or to a suitable location for drainage
i.e. a drain or sink.
Note! The minimum distance required
from the operating air conditioner to
any obstructing objects or walls is
50cm.
Keep the exhaust hose as short and
straight as possible and minimise
kinks. This will maximise the cooling
performance.
Don’t use extension pieces for the
exhaust pipe as this will reduce
performance and possibly result in
damage to the air conditioner.
Hot air and possibly mist will be
emitted from the exhaust hose.
Note! It is critical to the performance of
the unit that the hot exhaust air is
completely removed from the space
being cooled.
4CP15HW1 Portable Reverse Cycle Air Conditioner
To avoid damage to the control panel, do not operate with sharp objects.
NOTE!
8
CONTROL PANELAND DISPLAY
5
SEELEY INTERNATIONAL –OWNER’S MANUAL
7A
6
5
Press to turn the air
conditioner on and off
Press to cycle the fan
speed between low,
medium and high
Press to enter the
timer setting mode
and time
Press to cycle from
Cooling, Dehumidifying
and HeatingFan
Modes
Press to increase,
to decrease the
set temperature
In Timer mode, press
to increase, to
decrease the timer
from 01-24 hours
In Cooling mode, press
at same time to toggle
between °C and °F
Power ON / OFF
button
Fan Speed
control button
Timer Set
button
Mode Select
button
Set
Temperature
and Timer
Display
Remote
Control
Receiver
Fan Speed
Indicator Lights
Low - 1 Light
Medium - 2 Lights
High - 3 Lights
Mode
Indicator
Light
Blue - Cooling
Yellow - Dehumidify
Green - Fan
Red - Heating
Water Full
Indicator
Timer
Indicator
7B

If there are two of the same air
conditioners installed, they cannot be
controlled separately. When you operate
either remote, it will turn on both air
conditioners if they are both within signal
range (6 metres).
Care of your emote ontrolR C
Don’t let the remote control drop onto
hard surfaces or be subjected to sudden
shocks any . The warranty doesof form
not cover misuse or accidental damage.
Don’t place the remote control in direct
sunlight, or near extremes of temperature.
Don’t allow the remote control to get wet.
Don’t place near strong electromagnetic
waves.
Don’t mix old and new batteries!
If the remote control will not be used for a
long time, remove the batteries to avoid
corrosion.
Preparation efore perationB O
Remove the battery cover and insert new
batteries (AAA), making sure the + and -
match the compartment markings (Fig ).10
During Operation
If the remote control will not operate the air
conditioner, the batteries may need to be
replaced.
Remove the batteries and replace with new
ones. If this does not solve the problem
contact your nearest service centre for
advice.
Note! The air conditioner must be plugged in
and switched on for the remote control to
operate the air conditioner. To use, point at
the signal receiving window on the front
panel and press the remote button (Figure
8). The air conditioner will “beep” when a
signal has been received. If there is no beep,
press the remote button again, ensuring it is
within range (6 metres) of the air conditioner.
!
NOTE:
WASTE BATTERIES SHOULD
BE DISPOSED OF CORRECTLY
REMOTE CONTROL
9
Signal
transmission point
Signal
transmission point
Power ON / OFF
button
Power ON / OFF
button
Fan speed
adjust button
Fan speed
adjust button
Timer on / off
button
Timer on / off
button
Mode buttons
(Cool- Dehumidify-Fan)Heating-
Mode buttons
(Cool Dehumidify-Fan )- -Heating
Timer on / adjust
button
Temperature /Timer
adjust buttons
Battery
compartment
Battery
compartment
10
6CP15HW1 Portable Reverse Cycle Air Conditioner
Starting the air conditioner
Step 1: Ensure the cooler is plugged in
and switched on.
Step 2: Lift up the air outlet vent ready for
use.
Step : Press the ON/OFF button3
on the emote ontrol or ON/OFF buttonR C
on the ontrol anel to start the airC P
conditioner.
Step :4 Press the MODE button on
the ontrol anel or remote control toC P
select the desired operating mode
indicated by a light colour change on the
Display Panel 8 & 9(Fig ):
lCooling mode - efrigeratedR
cooling ooling will occur if the set. C
temperature is less than the room
temperature. Blue light indicated.
lDehumidifying mode - for extracting
moisture from the air. Yellow Light.
lFan mode - Fan only operation (no
cooling). Green Light.
lHeating Mode - Heating is activated
only if the ambient temperature is
below 25°C. Red light
Step :5 Press on thebuttonsor
C P R Control anel or on the emote ontrol to
select the desired operating ‘set’
temperature.
The set temperature range is 16°C- °C32
for cooling.
T 7°he set temperature range is 16°C-2 C
for heating.
Tip! Do not set the temperature too high
or low. This will consume more power.
24°C is the recommended set
temperature, with high fan speed.
Note! Changing the set temperature will
have no effect in DEHUMIDIFYING or
FAN modes.
Note! The display can toggle between °C
and °F by pressing both the and
buttons on the Control Panel together and
holding for 2 seconds.
Step :6 Press the FAN SPEED button
on the ontrol anel or remote control toC P
adjust the fan speed. Each press will cycle
the fan speed between low, medium and
high.
Note! In Cooling mode, the fan will continue
to run even when the compressor has
cycled off.
Step 7: The air conditioner is fitted with
horizontal . Cair direction vanes arefully
move the vanes to the desired position by
hand (Fig 1 ).1
Important! During operation, water will
collect in the air conditioner’s tank. Please
be careful when moving the air conditioner
to avoid water spillage.
Built in Drain Pump
The condensate produced during operation
will be drained automatically through the
drain hose when the drain pump outlet is
fitted. If Drain Pump Connector is not fitted
then the tank will slowly fill up. If the tank
should fill, the ‘water full’ indicator light will
be lit on the control display and the unit will
shut down until the water tank is drained.
Should this occur, connect Drain Pump
Connector (see Installation, Page 4) or refer
to Maintenance section for draining
instructions.
OPERATION
11
7
SEELEY INTERNATIONAL –OWNER’S MANUAL
ON/OFF
SPEED
TIMER
MODE
UP
DOWN
+
1.5V
1.5V
Battery cover
Battery cover
Important! During cooling mode, water will
collect in the air conditioner’s tank. This
water is reticulated and some will be
exhausted out with the hot air, but will
slowly fill up the tank. This occurs more
quickly in humid conditions. If the tank
should fill, the ‘water full’ indicator will be lit
on the control display and the unit will shut
down. The cooler cannot be restarted until
the water tank is drained. Refer to the
Maintenance section for draining the tank
should this occur.

If there are two of the same air
conditioners installed, they cannot be
controlled separately. When you operate
either remote, it will turn on both air
conditioners if they are both within signal
range (6 metres).
Care of your emote ontrolR C
Don’t let the remote control drop onto
hard surfaces or be subjected to sudden
shocks any . The warranty doesof form
not cover misuse or accidental damage.
Don’t place the remote control in direct
sunlight, or near extremes of temperature.
Don’t allow the remote control to get wet.
Don’t place near strong electromagnetic
waves.
Don’t mix old and new batteries!
If the remote control will not be used for a
long time, remove the batteries to avoid
corrosion.
Preparation efore perationB O
Remove the battery cover and insert new
batteries (AAA), making sure the + and -
match the compartment markings (Fig ).10
During Operation
If the remote control will not operate the air
conditioner, the batteries may need to be
replaced.
Remove the batteries and replace with new
ones. If this does not solve the problem
contact your nearest service centre for
advice.
Note! The air conditioner must be plugged in
and switched on for the remote control to
operate the air conditioner. To use, point at
the signal receiving window on the front
panel and press the remote button (Figure
8). The air conditioner will “beep” when a
signal has been received. If there is no beep,
press the remote button again, ensuring it is
within range (6 metres) of the air conditioner.
!
NOTE:
WASTE BATTERIES SHOULD
BE DISPOSED OF CORRECTLY
REMOTE CONTROL
9
Signal
transmission point
Signal
transmission point
Power ON / OFF
button
Power ON / OFF
button
Fan speed
adjust button
Fan speed
adjust button
Timer on / off
button
Timer on / off
button
Mode buttons
(Cool- Dehumidify-Fan)Heating-
Mode buttons
(Cool Dehumidify-Fan )- -Heating
Timer on / adjust
button
Temperature /Timer
adjust buttons
Battery
compartment
Battery
compartment
10
6CP15HW1 Portable Reverse Cycle Air Conditioner
Starting the air conditioner
Step 1: Ensure the cooler is plugged in
and switched on.
Step 2: Lift up the air outlet vent ready for
use.
Step : Press the ON/OFF button3
on the emote ontrol or ON/OFF buttonR C
on the ontrol anel to start the airC P
conditioner.
Step :4 Press the MODE button on
the ontrol anel or remote control toC P
select the desired operating mode
indicated by a light colour change on the
Display Panel 8 & 9(Fig ):
lCooling mode - efrigeratedR
cooling ooling will occur if the set. C
temperature is less than the room
temperature. Blue light indicated.
lDehumidifying mode - for extracting
moisture from the air. Yellow Light.
lFan mode - Fan only operation (no
cooling). Green Light.
lHeating Mode - Heating is activated
only if the ambient temperature is
below 25°C. Red light
Step :5 Press on thebuttonsor
C P R Control anel or on the emote ontrol to
select the desired operating ‘set’
temperature.
The set temperature range is 16°C- °C32
for cooling.
T 7°he set temperature range is 16°C-2 C
for heating.
Tip! Do not set the temperature too high
or low. This will consume more power.
24°C is the recommended set
temperature, with high fan speed.
Note! Changing the set temperature will
have no effect in DEHUMIDIFYING or
FAN modes.
Note! The display can toggle between °C
and °F by pressing both the and
buttons on the Control Panel together and
holding for 2 seconds.
Step :6 Press the FAN SPEED button
on the ontrol anel or remote control toC P
adjust the fan speed. Each press will cycle
the fan speed between low, medium and
high.
Note! In Cooling mode, the fan will continue
to run even when the compressor has
cycled off.
Step 7: The air conditioner is fitted with
horizontal . Cair direction vanes arefully
move the vanes to the desired position by
hand (Fig 1 ).1
Important! During operation, water will
collect in the air conditioner’s tank. Please
be careful when moving the air conditioner
to avoid water spillage.
Built in Drain Pump
The condensate produced during operation
will be drained automatically through the
drain hose when the drain pump outlet is
fitted. If Drain Pump Connector is not fitted
then the tank will slowly fill up. If the tank
should fill, the ‘water full’ indicator light will
be lit on the control display and the unit will
shut down until the water tank is drained.
Should this occur, connect Drain Pump
Connector (see Installation, Page 4) or refer
to Maintenance section for draining
instructions.
OPERATION
11
7
SEELEY INTERNATIONAL –OWNER’S MANUAL
ON/OFF
SPEED
TIMER
MODE
UP
DOWN
+
1.5V
1.5V
Battery cover
Battery cover
Important! During cooling mode, water will
collect in the air conditioner’s tank. This
water is reticulated and some will be
exhausted out with the hot air, but will
slowly fill up the tank. This occurs more
quickly in humid conditions. If the tank
should fill, the ‘water full’ indicator will be lit
on the control display and the unit will shut
down. The cooler cannot be restarted until
the water tank is drained. Refer to the
Maintenance section for draining the tank
should this occur.

OPERATION cont.
Timer Function
The air conditioner is fitted with a timer
function. This can be set up to 24 hours in
advance. To use this function, the cooler
must be plugged in and ready to operate.
Step : Setting the timer8
With the air conditioner ON, press the
TIMER button on the emote ontrol orR C
C P to set the number of hoursontrol anel
before the air conditioner powers off.
The ontrol anel display will flash andC P
show the time setting. Press the or
button to increase the time ins or decrease
1 hour increments from 1 - 24hrs. After 10
seconds the display will stop flashing and
the TIMER indicator will be lit on the display
panel (Fig 7).
When the air conditioner is OFF (but still
plugged in), repeat the above to set the
number of hours before the cooler powers
ON. The air conditioner will start up with the
last settings used.
Note! When the air conditioner is working,
only the TIMER OFF can be set. When the
air conditioner is off, only the TIMER ON
can be set.
How to cancel the timer
To cancel the timer, . Theset the timer to ‘00'
TIMER indicator will stop glowing.
CP15HW1 Portable Reverse Cycle Air Conditioner
8
Draining the Air Conditioner
P the unplugged air conditionerlace over a
drain point nscrew the cap and remov. U e
the drain plug t the bottom rear of thea
appliance Fig 12B) ter will flow out as( . Wa
soon as the plug is removed. llow theA
tank to completely drain before replacing
the drain plug and cap.
Removing the Drain Hose
Push the release button (Fig 12C) to
disengage the Drain Pump Connector.
Always disconnect the air conditioner from the electricity mains before cleaning or
draining.
To maximize the efficiency of the air conditioner, clean regularly.
Cleaning the housing
Use a soft, damp cloth to wipe the body clean.
Never use aggressive chemicals, spirits, detergents, chemically treated cloths, or other
cleansing solutions. These substances could possibly damage the cabinet.
Cleaning the filters
Remove the filter from the top air inlet vent as shown (Fig 12A).
Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt and then rinse
under running water (no hotter than 40°C).
Dry thoroughly before replacing.
Take care to replace the filter back into the slot in the cooler.
Note! Never operate the air conditioner without the filter.
End of season storage:
•Drain any water from the unit.
•Operate the unit in fan only mode for a few hours, to thoroughly dry the inside.
•Clean or change the filter.
•Unplug and carefully store the power cord and plug end.
•Replace in the original carton or cover for storage.
MAINTENANCE
B
12
12
A
C
Remove filter from the
air conditioner and
clean every 2 weeks.
9
SEELEY INTERNATIONAL –OWNER’S MANUAL
12