Seeley MASTERCOOL MIC User manual

®
OWNER’S MANUAL
Portable Evaporative Cooler
(English) (MI MIH MIC MICH MIV MIVH)
ILL863-A
(MI, MIH)
MILLENIA
ILL863-A
(MIV, MIVH)
MEGACOOL
ILL1222-A
(MIC, MICH)
MASTERCOOL

CONTENTS
SAFETY........................................................................ 1
General Safety
Electrical Safety
COMPONENT LOCATION........................................... 2
ASSEMBLY.................................................................. 3-4
Caution - Check Voltage
To assemble the cooler
DIRECTIONS FOR USE.............................................. 4-6
How to get the best cooling performance
Filling with water
Using the cooler - Low fan speed
High fan speed
Fan only (vent)
Conditioning of Aspen cooling pads
Air direction control
Safety instructions
Cleaning the cooler/rear panel removal
MAINTENANCE.......................................................... ..6-7
To drain water
Water strainer and Aspen cooling pad
Pump belt replacement / Drain Plug
TROUBLESHOOTING..................................................8
SPARE PARTS LIST & EXPLODED VIEW..................9-10
WARRANTY................................................................ . 11
Waste electrical products must not be disposed of with household waste. This product
should be taken to your local recycling centre for safe treatment.
iMillenia series Portable Evaporative Cooler
®
SEELEY INTERNATIONAL – OWNER’S MANUAL 1
SAFETY
Electrical Safety
Caution! before connecting the electrical
power cord to a power outlet, check that
the air cooler voltage is the same as your
power supply (refer to the rating label
located on the rear of the unit).
Do not pull the unit along by the power
cord or place the power cord near a
source of heat. Always unroll the power
cord completely before use.
If the power supply cord is damaged it
must be replaced by the manufacturer, a
service agent or qualified similarly
persons in order to avoid a hazard.
Switch off and unplug when not in use.
Portable evaporative air cooler -
important safety instructions
Please read these instructions before
assembling the cooler and keep for future
reference.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by
a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
General Safety
For indoor use only.
Use only in the upright position on a flat level
surface and at least 50cm from any objects.
Clean the air inlets and outlets at regular
intervals to prevent airflow reduction (refer
Maintenance section).
Do not place objects on the air cooler, or
through the ventilating slots or restrict the air
inlets & outlets.
Closely supervise any children and pets when
the air cooler is in use.
Do not store or operate the appliance near
any flammable substances.
During operation, water is present in the
bottom tank of the air cooler. Be careful when
moving the unit to prevent water from spilling.
Always switch your cooler off and unplug it
before cleaning or maintenance.

CONTENTS
SAFETY........................................................................ 1
General Safety
Electrical Safety
COMPONENT LOCATION........................................... 2
ASSEMBLY.................................................................. 3-4
Caution - Check Voltage
To assemble the cooler
DIRECTIONS FOR USE.............................................. 4-6
How to get the best cooling performance
Filling with water
Using the cooler - Low fan speed
High fan speed
Fan only (vent)
Conditioning of Aspen cooling pads
Air direction control
Safety instructions
Cleaning the cooler/rear panel removal
MAINTENANCE.......................................................... ..6-7
To drain water
Water strainer and Aspen cooling pad
Pump belt replacement / Drain Plug
TROUBLESHOOTING..................................................8
SPARE PARTS LIST & EXPLODED VIEW..................9-10
WARRANTY................................................................ . 11
Waste electrical products must not be disposed of with household waste. This product
should be taken to your local recycling centre for safe treatment.
iMillenia series Portable Evaporative Cooler
®
SEELEY INTERNATIONAL – OWNER’S MANUAL 1
SAFETY
Electrical Safety
Caution! before connecting the electrical
power cord to a power outlet, check that
the air cooler voltage is the same as your
power supply (refer to the rating label
located on the rear of the unit).
Do not pull the unit along by the power
cord or place the power cord near a
source of heat. Always unroll the power
cord completely before use.
If the power supply cord is damaged it
must be replaced by the manufacturer, a
service agent or qualified similarly
persons in order to avoid a hazard.
Switch off and unplug when not in use.
Portable evaporative air cooler -
important safety instructions
Please read these instructions before
assembling the cooler and keep for future
reference.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance by
a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
General Safety
For indoor use only.
Use only in the upright position on a flat level
surface and at least 50cm from any objects.
Clean the air inlets and outlets at regular
intervals to prevent airflow reduction (refer
Maintenance section).
Do not place objects on the air cooler, or
through the ventilating slots or restrict the air
inlets & outlets.
Closely supervise any children and pets when
the air cooler is in use.
Do not store or operate the appliance near
any flammable substances.
During operation, water is present in the
bottom tank of the air cooler. Be careful when
moving the unit to prevent water from spilling.
Always switch your cooler off and unplug it
before cleaning or maintenance.

2Millenia series Portable Evaporative Cooler
®
COMPONENT LOCATION
KEY
A Controls
B Front grille
C Water filling door
D Water reservoir
E Castors
F Water level indicator
G Front pillar ( llenia, Megacool)Mi
H Base
I Rear panel retaining screws (2)
J Rear panel
K Power cord entry point
L Reservoir drain plug
M Rating label
N Cord storage hooks
O Rear pillar ( llenia, Megacool)Mi
B
D
C
EH
F
G
A
ILL864-A ILL865- B
K
L
J
I
N
M
O
SEELEY INTERNATIONAL – OWNER’S MANUAL 3
8
ILL1221-A
CAUTION! - Check Voltage
Before connecting your electrical power
cord to a power outlet, check that the
cooler voltage is the same as your power
supply. The cooler voltage will be stated
on the rating label at the rear of the
cooler (Fig 6).
ASSEMBLY
ILL866-A
6
To assemble the cooler
Push the four castors into their locating
holes in the base. Use a rotating motion
to assist in the entry of the steel spring
ring (“ ” Fig 7). *
7
ILL867-B
*
Models llenia and Megacool onlyMi
Assemble the front and rear pillars and
screw together. Place this assembly on
the base and slide into position until it
locks (Fig 8).
Models llenia and Megacool onlyMi
Place the reservoir of the cooler onto the
front pillar as shown (Fig 9). Tilt
downwards towards the rear until the
reservoir locks onto the rear pillar.
To remove the unit from the pillars, use a
screwdriver in the two recesses in the
rear of the reservoir to release the clips.
Tilt the unit forward to remove.
ILL870-A
9

2Millenia series Portable Evaporative Cooler
®
COMPONENT LOCATION
KEY
A Controls
B Front grille
C Water filling door
D Water reservoir
E Castors
F Water level indicator
G Front pillar ( llenia, Megacool)Mi
H Base
I Rear panel retaining screws (2)
J Rear panel
K Power cord entry point
L Reservoir drain plug
M Rating label
N Cord storage hooks
O Rear pillar ( llenia, Megacool)Mi
B
D
C
EH
F
G
A
ILL864-A IL L 8 6 5- B
K
L
J
I
N
M
O
SEELEY INTERNATIONAL – OWNER’S MANUAL 3
8
ILL1221-A
CAUTION! - Check Voltage
Before connecting your electrical power
cord to a power outlet, check that the
cooler voltage is the same as your power
supply. The cooler voltage will be stated
on the rating label at the rear of the
cooler (Fig 6).
ASSEMBLY
ILL866-A
6
To assemble the cooler
Push the four castors into their locating
holes in the base. Use a rotating motion
to assist in the entry of the steel spring
ring (“ ” Fig 7). *
7
ILL867-B
*
Models llenia and Megacool onlyMi
Assemble the front and rear pillars and
screw together. Place this assembly on
the base and slide into position until it
locks (Fig 8).
Models llenia and Megacool onlyMi
Place the reservoir of the cooler onto the
front pillar as shown (Fig 9). Tilt
downwards towards the rear until the
reservoir locks onto the rear pillar.
To remove the unit from the pillars, use a
screwdriver in the two recesses in the
rear of the reservoir to release the clips.
Tilt the unit forward to remove.
ILL870-A
9

4
®
Millenia series Portable Evaporative Cooler
Model Mastercool only
Place the reservoir onto the base and
press down to engage the four clips in the
base (Fig 10).
To remove the cooler from the base, tip it
upside down and release the clips in the
base. A screwdriver may be necessary.
How to get the best cooling
performance
Place the cooler with its back near to an
open window or door so it can draw in
100% fresh air.
Open another window or door on the
opposite side of the room for “flow
through” ventilation. This cooler will not
cool properly in a closed room (Fig 11).
ILL1219-A
10
ILL871-A
11
ILL872-A
12
Filling with water
Turn the cooler off before filling. Open the
water filling door and pour in clean water
(Fig 12).
The water capacity is 14 litres. The
minimum amount of water needed for the
pump to operate is 2 litres.
The cooler is full when the water level
indicator is in the “FULL” position
(Fig 13). Do not overfill, as water will
spill out of the cooler!
Note! The cooler and pump will not be
DIRECTIONS FOR USE
FULL
EMPTY
13
ILL873-B
ASSEMBLY cont.
5SEELEY INTERNATIONAL – OWNER’S MANUAL
DIRECTIONS FOR USE cont.
Using the cooler
When this appliance is used as an air cooler,
it should be filled with water and the cool
knob turned to the “COOL” position (Fig 14).
Low fan speed (1) is selected for quietest
operation (Fig 14).
High fan speed (3) is for maximum cooling
(Fig 15).
Fan only (ventilation). This cooler may be
used as a fan only. Set the cool knob to
position “0” (Fig 15).
14
ILL1433-A
15
ILL1434-A
Conditioning of the aspen cooling
pad
To get the best performance from your cooler,
we recommend that when first used it is run
with water for at least 10 nutes at the mi
setting in Fig 16.
During this process the water becomes
slightly yellow, and there is a natural smell of
damp wood. This is normal.
Air direction control -
Millenia / Mastercool
The cooler is provided with air guide vanes
which can be adjusted as required to direct
the air flow.
Models llenia and Mastercool are adjusted Mi
manually by sliding the levers on the front
panel (Fig 17).
16
ILL1435-A
ILL877-C
MILLENIA / MASTERCOOL
17

4
®
Millenia series Portable Evaporative Cooler
Model Mastercool only
Place the reservoir onto the base and
press down to engage the four clips in the
base (Fig 10).
To remove the cooler from the base, tip it
upside down and release the clips in the
base. A screwdriver may be necessary.
How to get the best cooling
performance
Place the cooler with its back near to an
open window or door so it can draw in
100% fresh air.
Open another window or door on the
opposite side of the room for “flow
through” ventilation. This cooler will not
cool properly in a closed room (Fig 11).
ILL1219-A
10
ILL871-A
11
ILL872-A
12
Filling with water
Turn the cooler off before filling. Open the
water filling door and pour in clean water
(Fig 12).
The water capacity is 14 litres. The
minimum amount of water needed for the
pump to operate is 2 litres.
The cooler is full when the water level
indicator is in the “FULL” position
(Fig 13). Do not overfill, as water will
spill out of the cooler!
Note! The cooler and pump will not be
DIRECTIONS FOR USE
FULL
EMPTY
13
ILL873-B
ASSEMBLY cont.
5SEELEY INTERNATIONAL – OWNER’S MANUAL
DIRECTIONS FOR USE cont.
Using the cooler
When this appliance is used as an air cooler,
it should be filled with water and the cool
knob turned to the “COOL” position (Fig 14).
Low fan speed (1) is selected for quietest
operation (Fig 14).
High fan speed (3) is for maximum cooling
(Fig 15).
Fan only (ventilation). This cooler may be
used as a fan only. Set the cool knob to
position “0” (Fig 15).
14
ILL1433-A
15
ILL1434-A
Conditioning of the aspen cooling
pad
To get the best performance from your cooler,
we recommend that when first used it is run
with water for at least 10 nutes at the mi
setting in Fig 16.
During this process the water becomes
slightly yellow, and there is a natural smell of
damp wood. This is normal.
Air direction control -
Millenia / Mastercool
The cooler is provided with air guide vanes
which can be adjusted as required to direct
the air flow.
Models llenia and Mastercool are adjusted Mi
manually by sliding the levers on the front
panel (Fig 17).
16
ILL1435-A
ILL877-C
MILLENIA / MASTERCOOL
17

6
®
Millenia series Portable Evaporative Cooler
Air direction control Megacool
Model Megacool has motor driven vanes
that are switched on and off by the fan
control switch on the control panel (Fig
18). Set the control to the “sweep / fan”
speed setting to operate the sweep vanes
(shown). Set to “fan” speed settings for
fixed direction.
There are no manual adjustment levers.
Cleaning the cooler
Important! Always switch off and
remove the electrical plug before
cleaning and servicing the
cooler.
To clean, wipe the cooler with a damp
cloth and a little household detergent.
The rear panel can be removed to gain
access to inside the cooler by removing
the screws at the top of each side.
Pivot the panel backwards and lift off
(Fig 20). ILL880-B
20
Safety instruction
As this cooler contains water, ensure it is
moved carefully and is not tilted, as water
may spill (Fig 19).
ILL878-B
19
18
ILL1436-A
MAINTENANCE
DIRECTIONS FOR USE cont. MAINTENANCE cont.
End of Season
At least once a year at the end of summer it
is advisable to do some simple maintenance
on your cooler to maintain its high efficiency.
This involves cleaning the water system and
the Aspen cooling pad.
To drain water
Drain the water from the cooler by moving the
cooler to a drain and removing the drain plug
located on the bottom of the tank. When the
cooler is empty replace the plug in the tank
(Fig 21).
ILL879-A
21
A
BA
ILL882-B
22
Pump belt replacement
If a pump drive belt needs replacing, access
can be gained by using a tool (screwdriver) to
remove the small access door (Fig 22 - “A”).
Spare drain plug
Each cooler is supplied with a spare drain
plug, located in the position shown (Fig 22 -
“B”).
Water strainer and aspen cooling pad
Clean the water strainer by removing any
foreign matter. Wash the Aspen cooling pad
with water while it is still in the rear panel.
Replace the pad if it is worn or deteriorated.
7SEELEY INTERNATIONAL – OWNER’S MANUAL

6
®
Millenia series Portable Evaporative Cooler
Air direction control Megacool
Model Megacool has motor driven vanes
that are switched on and off by the fan
control switch on the control panel (Fig
18). Set the control to the “sweep / fan”
speed setting to operate the sweep vanes
(shown). Set to “fan” speed settings for
fixed direction.
There are no manual adjustment levers.
Cleaning the cooler
Important! Always switch off and
remove the electrical plug before
cleaning and servicing the
cooler.
To clean, wipe the cooler with a damp
cloth and a little household detergent.
The rear panel can be removed to gain
access to inside the cooler by removing
the screws at the top of each side.
Pivot the panel backwards and lift off
(Fig 20). ILL880-B
20
Safety instruction
As this cooler contains water, ensure it is
moved carefully and is not tilted, as water
may spill (Fig 19).
ILL878-B
19
18
ILL1436-A
MAINTENANCE
DIRECTIONS FOR USE cont. MAINTENANCE cont.
End of Season
At least once a year at the end of summer it
is advisable to do some simple maintenance
on your cooler to maintain its high efficiency.
This involves cleaning the water system and
the Aspen cooling pad.
To drain water
Drain the water from the cooler by moving the
cooler to a drain and removing the drain plug
located on the bottom of the tank. When the
cooler is empty replace the plug in the tank
(Fig 21).
ILL879-A
21
A
BA
ILL882-B
22
Pump belt replacement
If a pump drive belt needs replacing, access
can be gained by using a tool (screwdriver) to
remove the small access door (Fig 22 - “A”).
Spare drain plug
Each cooler is supplied with a spare drain
plug, located in the position shown (Fig 22 -
“B”).
Water strainer and aspen cooling pad
Clean the water strainer by removing any
foreign matter. Wash the Aspen cooling pad
with water while it is still in the rear panel.
Replace the pad if it is worn or deteriorated.
7SEELEY INTERNATIONAL – OWNER’S MANUAL

8
®
Millenia series Portable Evaporative Cooler
3.6 Fan/pump not running
fast enough on low speed.
3.7 Pump drive belt faulty
or broken.
3.6.1 Check that supply voltage is up to correct level.
3.6.2 Fan and pump will pick up speed slightly as the motor
reaches normal operating temperature. Allow the cooler to
run for 30-60 nutes and check again. If there is no mi
improvement have the cooler checked by a service agent.
4.1 Reservoir or Aspen
cooling pad dirty.
4.2 Water quality is poor.
4.1.1 Drain reservoir and fill the cooler with clean water. If it
still smells clean the reservoir and replace the Aspen cooling
pad or proceed to 4.2.1.
4.2.1 Add a little vanilla essence or perfume to the water.
4. Cooler makes bad
smell.
5.1 Dirt has accumulated
inside pump.
5.1.1 Proceed as in 3.5.1
5.1.2 Replace drive belt as shown on page 7.
5. Cooler makes
scraping or rattling
noise on new season
start up.
6.1 Too much water in
reservoir.
6.2 Water level indicator
not working.
6.1.1 Drain some water out (see page 7).
6.2.1 Remove the rear panel for access. Slide the indicator
up to the 'FULL' position then let it drop. If it fails to operate
have it checked by a service agent.
6. Water overflows from
reservoir.
7.1 Electrical fault. 7.1.1 Electrical parts must only be repaired and replaced by
Authorised Service Agents.
7. Cooler will not
operate at all.
8.1.1 If the power supply cord of this appliance is damaged it
must be replaced. Electrical parts must only be repaired and
replaced by Authorised Service Agents.
8. Damaged power
supply cord.
3. No cooling. 3.1 Cooling control is off.
3.2 Reservoir is empty or
nearly empty.
3.3 Weather is too hu d.mi
3.4 Aspen cooling pad and
/ or pump inlet screen
blocked or dirty.
3.5 Pump is not working
3.1.1 Turn cool knob to 'COOL'.
3.2.1 Fill with water again until water level indicator is at the
'FULL' position. Water capacity is 14 litres
3.3.1 Turn cool knob to '0' and use cooler as a fan only.
3.4.1 Clean parts - see maintenance page 6.
3.5.1 The pump is NOT a separate electric pump. It is
connected to the fan motor and is driven mechanically. Turn
the cooler off and completely drain the reservoir. Refill with
water. Switch fan knob to high speed (3), turn the cool knob
to 'COOL',run the cooler for 10-15 nutes non-stop. This will mi
help dissolve and flush out the dirt. The Aspen cooling pad
should now be wet. If the pad is not visibly wet and there is
no cooling, have the cooler checked by a service agent.
1. Cooler will not
operate at first.
2. Cooler stops
operating after running
for some time and does
not restart.
1.1 Power outlet or supply
faulty.
1.2 Wrong voltage.
2.1 Motor in safety
shutdown.
1.1.1 Switch on power outlet.
1.1.2 Check power supply.
1.1.3 Check power outlet.
1.2.1 Check that power supply is the same as specified on
the rating label.
2.1.1 Motor must be replaced by Authorised Service Agent.
TROUBLESHOOTING
CONDITION POSSIBLE CAUSE REMEDY
9SEELEY INTERNATIONAL – OWNER’S MANUAL
When ordering spare parts, please specify the model / serial number
and colour of your cooler.
SPARE PARTS LIST
Item Description
1Tank (includes drain plug)
2Drain Plug
3Rear Panel
4Filter Pad
5Front Grille Assembly
6Badge - Front Grille
7Window
8Filler Door
9Mid Panel Assembly
10 Inner Grille / Spreader Assembly
11 Inner Grille Door
12 Screws
13 Front / Rear Pillar (pair)
14 Base
14.1 Base - compact
15 Castor & Pintle Assembly
16 Control Panel
17 Control Box
18
18.1
Knob Mushroom Knob Mushroom & Shaft Assembly
19 Water Valve Assembly
20
20.1
Switch (2006 - ) llenia / Mastercool
Mi
Switch (2006 - ) Megacool
22 Lever Vane
23 Vane Link RH
24 Vane Link LH
25 Vane
26 Vane Bearing
27 Vane Link Motor
(llenia / Megacool)
Mi
(llenia / Megacool only)
Mi
(Mastercool only)
Item Description
28 Pad Clamp
29 Water Level Indicator
30 Float Assembly
31 Pump Assembly
32 Strainer
33 Vane Motor
34 Vane Motor Hub
36 Fan Pulley
37 Fan
38 Drive Belt
39 Spreader Hose 9.5 x 450
41 Pump Hose 9.5 x 890
42
42.1
Motor Rubbers White for Square Motor Motor Rubbers Black for Round Motor
43.1
43
Electric Motor 230V 50Hz - Round Electric Motor 230V 50Hz - Square
44 Capacitor 3.2uf for Motor
46 Plug & Cord Australia
47 Cord Grip - Flat Cord 4K-1
(Megacool only)
(Megacool only)

8
®
Millenia series Portable Evaporative Cooler
3.6 Fan/pump not running
fast enough on low speed.
3.7 Pump drive belt faulty
or broken.
3.6.1 Check that supply voltage is up to correct level.
3.6.2 Fan and pump will pick up speed slightly as the motor
reaches normal operating temperature. Allow the cooler to
run for 30-60 nutes and check again. If there is no mi
improvement have the cooler checked by a service agent.
4.1 Reservoir or Aspen
cooling pad dirty.
4.2 Water quality is poor.
4.1.1 Drain reservoir and fill the cooler with clean water. If it
still smells clean the reservoir and replace the Aspen cooling
pad or proceed to 4.2.1.
4.2.1 Add a little vanilla essence or perfume to the water.
4. Cooler makes bad
smell.
5.1 Dirt has accumulated
inside pump.
5.1.1 Proceed as in 3.5.1
5.1.2 Replace drive belt as shown on page 7.
5. Cooler makes
scraping or rattling
noise on new season
start up.
6.1 Too much water in
reservoir.
6.2 Water level indicator
not working.
6.1.1 Drain some water out (see page 7).
6.2.1 Remove the rear panel for access. Slide the indicator
up to the 'FULL' position then let it drop. If it fails to operate
have it checked by a service agent.
6. Water overflows from
reservoir.
7.1 Electrical fault. 7.1.1 Electrical parts must only be repaired and replaced by
Authorised Service Agents.
7. Cooler will not
operate at all.
8.1.1 If the power supply cord of this appliance is damaged it
must be replaced. Electrical parts must only be repaired and
replaced by Authorised Service Agents.
8. Damaged power
supply cord.
3. No cooling. 3.1 Cooling control is off.
3.2 Reservoir is empty or
nearly empty.
3.3 Weather is too hu d.mi
3.4 Aspen cooling pad and
/ or pump inlet screen
blocked or dirty.
3.5 Pump is not working
3.1.1 Turn cool knob to 'COOL'.
3.2.1 Fill with water again until water level indicator is at the
'FULL' position. Water capacity is 14 litres
3.3.1 Turn cool knob to '0' and use cooler as a fan only.
3.4.1 Clean parts - see maintenance page 6.
3.5.1 The pump is NOT a separate electric pump. It is
connected to the fan motor and is driven mechanically. Turn
the cooler off and completely drain the reservoir. Refill with
water. Switch fan knob to high speed (3), turn the cool knob
to 'COOL',run the cooler for 10-15 nutes non-stop. This will mi
help dissolve and flush out the dirt. The Aspen cooling pad
should now be wet. If the pad is not visibly wet and there is
no cooling, have the cooler checked by a service agent.
1. Cooler will not
operate at first.
2. Cooler stops
operating after running
for some time and does
not restart.
1.1 Power outlet or supply
faulty.
1.2 Wrong voltage.
2.1 Motor in safety
shutdown.
1.1.1 Switch on power outlet.
1.1.2 Check power supply.
1.1.3 Check power outlet.
1.2.1 Check that power supply is the same as specified on
the rating label.
2.1.1 Motor must be replaced by Authorised Service Agent.
TROUBLESHOOTING
CONDITION POSSIBLE CAUSE REMEDY
9SEELEY INTERNATIONAL – OWNER’S MANUAL
When ordering spare parts, please specify the model / serial number
and colour of your cooler.
SPARE PARTS LIST
Item Description
1Tank (includes drain plug)
2Drain Plug
3Rear Panel
4Filter Pad
5Front Grille Assembly
6Badge - Front Grille
7Window
8Filler Door
9Mid Panel Assembly
10 Inner Grille / Spreader Assembly
11 Inner Grille Door
12 Screws
13 Front / Rear Pillar (pair)
14 Base
14.1 Base - compact
15 Castor & Pintle Assembly
16 Control Panel
17 Control Box
18
18.1
Knob Mushroom Knob Mushroom & Shaft Assembly
19 Water Valve Assembly
20
20.1
Switch (2006 - ) llenia / Mastercool
Mi
Switch (2006 - ) Megacool
22 Lever Vane
23 Vane Link RH
24 Vane Link LH
25 Vane
26 Vane Bearing
27 Vane Link Motor
(llenia / Megacool)
Mi
(llenia / Megacool only)
Mi
(Mastercool only)
Item Description
28 Pad Clamp
29 Water Level Indicator
30 Float Assembly
31 Pump Assembly
32 Strainer
33 Vane Motor
34 Vane Motor Hub
36 Fan Pulley
37 Fan
38 Drive Belt
39 Spreader Hose 9.5 x 450
41 Pump Hose 9.5 x 890
42
42.1
Motor Rubbers White for Square Motor Motor Rubbers Black for Round Motor
43.1
43
Electric Motor 230V 50Hz - Round Electric Motor 230V 50Hz - Square
44 Capacitor 3.2uf for Motor
46 Plug & Cord Australia
47 Cord Grip - Flat Cord 4K-1
(Megacool only)
(Megacool only)

10
®
Millenia series Portable Evaporative Cooler
As the policy of this company is one of continuous improvement, all specifications are subject to change without notice.
7 29 30 1 2
526 25 24 41 39 19
18.1
18 16 20 44 17 43 42 36 43
10
11
38
932 31 37
14
13
15
23
27 33 34
46 47
12
28
Millenia
Megacool Mastercool
8
22 6 12
ILL1432-A 0609
EXPLODED VIEW
11SEELEY INTERNATIONAL – OWNER’S MANUAL
In this warranty:
We or us means Seeley International Pty Ltd ABN 23 054 687 035, and our contact details
are set out at the end of this warranty;
You means you, the original end-user purchaser of the Goods;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia; and
Goods means the product, unit, appliance or equipment which was accompanied by this
warranty and purchased in Australia.
Our Goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the
Goods repaired or replaced if the Goods fail to be of acceptable quality and the failure
does not amount to a major failure.
In addition to any rights and remedies that You may have under the Australian Consumer
Law or any other law, subject to the terms of this warranty, We provide the following
warranty:
1. If, during the first 24 months from the date of first retail purchase (Warranty Period),
the Goods upon exa nation prove defective by reason of improper workmanship or mi
material, We will repair at our nearest service centre or replace (at our option), the
product or any part thereof without charge. Should we deem in our absolute discretion
to replace the Goods, we may substitute any si lar good even if it is not on our current mi
price/equipment list. Further, Goods presented for repair may be replaced by
refurbished goods of the same type rather than being repaired. Refurbished parts may
be used to repair the Goods.
2. We are under no obligation to repair or replace the Goods under clause 1 if the Goods
have not been used only for personal, domestic or household purposes or have not
been operated and maintained in accordance with the instructions in the Owner's
Manual. The addition of any third party device or the removal or the alteration of any of
our components will void this warranty. In addition, the warranty granted under clause 1
does not apply to:
• Consumable components such as filters,
• Adjustments necessary due to suse of the cooler,mi
• Normal user maintenance,
• Setting of controls,
• Transit damage, or
• Damage caused by user suse, tampering, or failure to observe the care and mi
special provisions in the instructions.
3. The warranty granted under clause 1 is li ed to repair or replacement only. As far as mit
the law per ts, We will not be liable for any consequential loss suffered through, or mi
resulting from, the non operation, or ineffective operation of the Goods. The warranty
granted under clause 1 does not cover damage to the Goods or other loss resulting
from acts of God.
WARRANTY

10
®
Millenia series Portable Evaporative Cooler
As the policy of this company is one of continuous improvement, all specifications are subject to change without notice.
7 29 30 1 2
526 25 24 41 39 19
18.1
18 16 20 44 17 43 42 36 43
10
11
38
932 31 37
14
13
15
23
27 33 34
46 47
12
28
Millenia
Megacool Mastercool
8
22 6 12
ILL1432-A 0609
EXPLODED VIEW
11SEELEY INTERNATIONAL – OWNER’S MANUAL
In this warranty:
We or us means Seeley International Pty Ltd ABN 23 054 687 035, and our contact details
are set out at the end of this warranty;
You means you, the original end-user purchaser of the Goods;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia; and
Goods means the product, unit, appliance or equipment which was accompanied by this
warranty and purchased in Australia.
Our Goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the
Goods repaired or replaced if the Goods fail to be of acceptable quality and the failure
does not amount to a major failure.
In addition to any rights and remedies that You may have under the Australian Consumer
Law or any other law, subject to the terms of this warranty, We provide the following
warranty:
1. If, during the first 24 months from the date of first retail purchase (Warranty Period),
the Goods upon exa nation prove defective by reason of improper workmanship or mi
material, We will repair at our nearest service centre or replace (at our option), the
product or any part thereof without charge. Should we deem in our absolute discretion
to replace the Goods, we may substitute any si lar good even if it is not on our current mi
price/equipment list. Further, Goods presented for repair may be replaced by
refurbished goods of the same type rather than being repaired. Refurbished parts may
be used to repair the Goods.
2. We are under no obligation to repair or replace the Goods under clause 1 if the Goods
have not been used only for personal, domestic or household purposes or have not
been operated and maintained in accordance with the instructions in the Owner's
Manual. The addition of any third party device or the removal or the alteration of any of
our components will void this warranty. In addition, the warranty granted under clause 1
does not apply to:
• Consumable components such as filters,
• Adjustments necessary due to suse of the cooler,mi
• Normal user maintenance,
• Setting of controls,
• Transit damage, or
• Damage caused by user suse, tampering, or failure to observe the care and mi
special provisions in the instructions.
3. The warranty granted under clause 1 is li ed to repair or replacement only. As far as mit
the law per ts, We will not be liable for any consequential loss suffered through, or mi
resulting from, the non operation, or ineffective operation of the Goods. The warranty
granted under clause 1 does not cover damage to the Goods or other loss resulting
from acts of God.
WARRANTY

SEELEY INTERNATIONAL – OWNER’S MANUAL 13
WARRANTY cont.
4. We are not responsible in any way for any failure and/or inadequate performance of the
Goods which arises from or is connected to the use in the Goods of non-genuine spare
parts. We strongly recommend that only spare parts supplied or approved by us are
used in the Goods.
5. No other person, firm or corporation is authorised by us to offer or give on our behalf
any other or greater warranty than that given under this warranty. The benefits
conferred by this warranty are in favour of You and any person deriving title to the
Goods through or under such person and are intended to be separate from and
additional to all other rights and remedies that they may have in law in respect of the
Goods.
6. In order to claim under the warranty granted under clause 1 you must:
(a) either:
(i) contact us within the Warranty Period on: 1300 650 644;
or
(ii) log a claim on our website www.seeleyinternational.com within the Warranty
Period; and
(b) return the Goods to your nearest service centre (or to us at the address below) by
prepaid freight within the Warranty Period, together with (i) the legible and
unmodified proof of purchase, which clearly indicates the name and address of the
original retailer, the date and place of purchase, the product name or other product
serial number, and (ii) a copy of the completed Warranty Information page below.
(If you choose to return the Goods to us, there is an additional requirement - they
will also need to be accompanied by a covering letter which states your name and
address and daytime telephone number, and the model and serial number of the
goods.)
7. This warranty does not cover the cost of clai ng under the warranty, it is your mi
responsibility to cover all forwarding and return freight costs incurred in sending the
Goods to and from your nearest service centre or us.
8. This warranty is only valid and enforceable in Australia.
Our liability under this warranty is li ted to the extent per tted by law. That is, to the mi mi
extent that it is fair and reasonable, if the Goods are not of a kind ordinarily acquired for
personal, domestic or household use or consumption, your remedies associated with any
failure or defect of the Product will be li ted to:mi
(a) the replacement of the Goods or the supply of equivalent goods;
(b) the repair of the Goods;
(c) the payment of the cost of replacing the Goods or of acquiring equivalent goods;
(d) the payment of the cost of having the Goods repaired
12
®
Millenia series Portable Evaporative Cooler
WARRANTY cont.
To ensure that service either pursuant to the above warranty or otherwise is readily
available, we have established in all States authorised service centres, which are available
to deal with service requirements.
For further information about your nearest service centre and other enquiries please call
our Service Centre on:
1300 650 644
Please retain your receipt as proof of purchase. Every request for warranty must be
accompanied by proof of purchase.
Complete the following for your records:
Serial Number:
Product: Convair
Model:  Mastercool  MIC, MICH Millenia MI, MIH
 Megacool H MIV, MIV
Purchased from: ...................................................................
...................................................................
...................................................................
Date purchased: ....../....../......
Service Department
Seeley International Pty Ltd
112 O'Sullivan Beach Road, Lonsdale, South Australia, 5160
Customer service centre in Australia: 1300 650 644
Website: www.seeleyinternational.com

SEELEY INTERNATIONAL – OWNER’S MANUAL 13
WARRANTY cont.
4. We are not responsible in any way for any failure and/or inadequate performance of the
Goods which arises from or is connected to the use in the Goods of non-genuine spare
parts. We strongly recommend that only spare parts supplied or approved by us are
used in the Goods.
5. No other person, firm or corporation is authorised by us to offer or give on our behalf
any other or greater warranty than that given under this warranty. The benefits
conferred by this warranty are in favour of You and any person deriving title to the
Goods through or under such person and are intended to be separate from and
additional to all other rights and remedies that they may have in law in respect of the
Goods.
6. In order to claim under the warranty granted under clause 1 you must:
(a) either:
(i) contact us within the Warranty Period on: 1300 650 644;
or
(ii) log a claim on our website www.seeleyinternational.com within the Warranty
Period; and
(b) return the Goods to your nearest service centre (or to us at the address below) by
prepaid freight within the Warranty Period, together with (i) the legible and
unmodified proof of purchase, which clearly indicates the name and address of the
original retailer, the date and place of purchase, the product name or other product
serial number, and (ii) a copy of the completed Warranty Information page below.
(If you choose to return the Goods to us, there is an additional requirement - they
will also need to be accompanied by a covering letter which states your name and
address and daytime telephone number, and the model and serial number of the
goods.)
7. This warranty does not cover the cost of clai ng under the warranty, it is your mi
responsibility to cover all forwarding and return freight costs incurred in sending the
Goods to and from your nearest service centre or us.
8. This warranty is only valid and enforceable in Australia.
Our liability under this warranty is li ted to the extent per tted by law. That is, to the mi mi
extent that it is fair and reasonable, if the Goods are not of a kind ordinarily acquired for
personal, domestic or household use or consumption, your remedies associated with any
failure or defect of the Product will be li ted to:mi
(a) the replacement of the Goods or the supply of equivalent goods;
(b) the repair of the Goods;
(c) the payment of the cost of replacing the Goods or of acquiring equivalent goods;
(d) the payment of the cost of having the Goods repaired
12
®
Millenia series Portable Evaporative Cooler
WARRANTY cont.
To ensure that service either pursuant to the above warranty or otherwise is readily
available, we have established in all States authorised service centres, which are available
to deal with service requirements.
For further information about your nearest service centre and other enquiries please call
our Service Centre on:
1300 650 644
Please retain your receipt as proof of purchase. Every request for warranty must be
accompanied by proof of purchase.
Complete the following for your records:
Serial Number:
Product: Convair
Model:  Mastercool  MIC, MICH Millenia MI, MIH
 Megacool H MIV, MIV
Purchased from: ...................................................................
...................................................................
...................................................................
Date purchased: ....../....../......
Service Department
Seeley International Pty Ltd
112 O'Sullivan Beach Road, Lonsdale, South Australia, 5160
Customer service centre in Australia: 1300 650 644
Website: www.seeleyinternational.com

829524-E convair.net.au AU 1208
Warranty Service
Australia 1-300-650-644
seeleyinternational.com
It is the policy of Seeley International to introduce continual
product improvement. Accordingly, specifications are
subject to change without notice. Please consult with your
dealer to confirm the specifications of the model selected.
®