Seiko CT-2000 User manual

表紙
Thank you for purchasing SEIKO SPORTS PRINTER CT-2000.
Before using your SEIKO SPORTS PRINTER, please read this
manual carefully for its proper use and care.
Keep this manual handy for ready reference.

CAUTION
（1） This manual may not be copied or reproduced in any form, in whole or in part, without the
express written consent of SEIKO.
（2） This manual may be subject to change without prior notice.
（3） This manual has been prepared carefully to provide you with complete information for the
operation of this product. For the purpose of constant improvement in this manual, your
suggestions and comments on the descriptions included herein are highly appreciated.
（4） SEIKO shall not be liable for any failure of this product or direct or indirect damages resulting
from such failure if such failure is caused due to abuse or misuse of the product, failure to
observe instructions herein or neglect of other reasonable care, or servicing, changes,
modifications or alterations performed by other than SEIKO or a servicing contractor
authorized by SEIKO.
SAFETY ALERT SYMBOLS
The following symbols and terms used in this manual have the meaning as explained below. They
are intended to attract special attention of the users to the descriptions attached with them so that they
can use the product properly to prevent personal injuries and property damages. Before reading this
manual, be sure to understand what they mean.
WARNING
This pictorial symbol with WARNING is used to indicate a potentially
hazardous situation which is likely to cause death or severe personal
injury if the instructions attached with them are not followed correctly.
CAUTION
This pictorial symbol with CAUTION is used to indicate a potentially
hazardous situation which is likely to cause personal injury or property
damage if the instructions under attached with them are not followed
correctly.
This pictorial symbol indicates what must NOT be done.
This pictorial symbol indicates what must be done.

ー TABLE OF CONTENTS －
1. SAFETY PRECAUTIONS ............................................................................................................................................. 1
2. INTRODUCTION ............................................................................................................................................................... 3
2.1 Overview...........................................................................................................................3
2.2 Features............................................................................................................................3
2.3 Lap Time and Split Time...................................................................................................4
2.4 System Components ........................................................................................................4
2.5 How to Open the Case .....................................................................................................5
2.6 Power Supply....................................................................................................................5
3. NAMES AND FUNCTIONS OF PARTS.......................................................................................................... 6
3.1 Battery Compartment........................................................................................................6
3.1.1 How to Install the Batteries ..................................................................................................................................................................... 6
3.2 Connector Section ............................................................................................................7
3.3 Printer Section ..................................................................................................................8
3.3.1 How to Install a Roll Paper ..................................................................................................................................................................... 9
3.3.2 How to Replace the Ribbon Cassette ........................................................................................................................................ 11
3.4 Monitor Section...............................................................................................................12
3.4.1 Memory ................................................................................................................................................................................................................. 12
3.4.2 Memory Block .................................................................................................................................................................................................. 13
3.4.3 Measurement Mode ................................................................................................................................................................................... 13
3.4.4 TIME UNIT ......................................................................................................................................................................................................... 14
3.4.5 BATT.1, BATT.2 (Remaining Power) ......................................................................................................................................... 14
3.5 Operation Section ...........................................................................................................15
4. SETTING PROCEDURE ............................................................................................................................................ 17
4.1 Time/Calendar Setting ....................................................................................................17
4.2 Dry Battery Setting..........................................................................................................18
4.3 Measurement Mode Setting............................................................................................19
4.3.1 List of Setting Items Available for Each Measurement Mode ............................................................................... 20
4.4 How to Start Each Measurement Mode ..........................................................................21
5. MEASUREMENT MODE ......................................................................................................................................... 22
5.1 Counting Mode (Measurement Mode No. 1)...................................................................22
5.1.1 Features ............................................................................................................................................................................................................... 22
5.1.2 Operating Method ........................................................................................................................................................................................ 22
5.1.3 Example Printout .......................................................................................................................................................................................... 23
5.2 Parallel Counting Mode (Measurement Mode No. 2)......................................................24
5.2.1 Features ............................................................................................................................................................................................................... 24
5.2.2 Operating Method ........................................................................................................................................................................................ 24
5.2.3 Example Printout .......................................................................................................................................................................................... 25
5.3 Parallel Lap/Split Time Measurement Mode (Measurement Mode No. 3) ......................26
5.3.1 Features ............................................................................................................................................................................................................... 26
5.3.2 Operating Method ........................................................................................................................................................................................ 26
5.3.3 Example Printout .......................................................................................................................................................................................... 27
5.4 Parallel Delayed Start Mode (Measurement Mode No. 4) ..............................................28
5.4.1 Features ............................................................................................................................................................................................................... 28
5.4.2 Operating Method ........................................................................................................................................................................................ 28
5.4.3 Example Printout .......................................................................................................................................................................................... 29

5.5 Time Correction Mode (Measurement Mode No. 5) .......................................................30
5.5.1 Features ............................................................................................................................................................................................................... 30
5.5.2 Operating Method (Master Unit) ..................................................................................................................................................... 30
5.5.3 Example Printout (Master Unit) ....................................................................................................................................................... 32
5.5.4 Operating Method (Secondary Unit) ........................................................................................................................................... 32
5.5.5 Example Printout (Secondary Unit) ............................................................................................................................................. 34
5.6 Auto Measurement-1 Mode (Measurement Mode No. 6) ...............................................35
5.6.1 Features ............................................................................................................................................................................................................... 35
5.6.2 Operating Method ........................................................................................................................................................................................ 35
5.6.3 Example Printout .......................................................................................................................................................................................... 36
5.7 Auto Measurement-2 Mode (Measurement Mode NO. 7)...............................................37
5.7.1 Features ............................................................................................................................................................................................................... 37
5.7.2 Operating Method ........................................................................................................................................................................................ 37
5.7.3 Example Printout .......................................................................................................................................................................................... 38
5.8 Speed Measurement Mode (Measurement Mode No. 8)................................................39
5.8.1 Features ............................................................................................................................................................................................................... 39
5.8.2 Operating Method ........................................................................................................................................................................................ 39
5.8.3 Example Printout .......................................................................................................................................................................................... 40
6. OTHER FUNCTIONS ................................................................................................................................................. 41
6.1 Start Time Setting ...........................................................................................................41
6.1.1 Operating Method ........................................................................................................................................................................................ 41
6.2 Resetting Order of Arrival ...............................................................................................42
6.2.1 Operating Method ........................................................................................................................................................................................ 42
6.2.2 Example Printout .......................................................................................................................................................................................... 42
6.3 Inputting Bib No. .............................................................................................................43
6.3.1 Operating Method ........................................................................................................................................................................................ 43
6.3.2 Example Printout .......................................................................................................................................................................................... 43
6.4 Memory Recall................................................................................................................44
6.4.1 Operating Method ........................................................................................................................................................................................ 44
6.5 Reprinting Data in Memory .............................................................................................45
6.5.1 Operating Method ........................................................................................................................................................................................ 45
6.5.2 Example Printout .......................................................................................................................................................................................... 45
6.6 How to Clear Data in Memory.........................................................................................46
6.6.1 Operating Method ........................................................................................................................................................................................ 46
6.7 LOCK Switch ..................................................................................................................47
6.8 SYNC (Synchronization).................................................................................................48
6.8.1 Method of Synchronization via Start Signal .......................................................................................................................... 48
6.8.2 Method of Synchronization after Start ....................................................................................................................................... 48
6.9 PC DATA (Output of Data to Personal Computer)..........................................................50
6.9.1 Communication Specifications ......................................................................................................................................................... 50
6.9.2 Data format ........................................................................................................................................................................................................ 51
6.9.3 Data Format (Speed) ................................................................................................................................................................................ 52
7. TROUBLESHOOTING ............................................................................................................................................... 53
8. SPECIFICATIONS ......................................................................................................................................................... 54

- 1 -
1. SAFETY PRECAUTIONS
The following precautions must be strictly observed for the safety of yourself and your fellow workers
and for the protection of property from loss and damages.
WARNING
If the Product is giving out smoke or burnt smell, or showing
other abnormal symptoms, turn off the power switch and stop
using it. Then, checking that no more smoke is given out, call
your nearby SEIKO dealer or agent for repair service.
Unless you are a qualified electrician, never try to disassemble,
repair or modify the Product. Unauthorized disassembly, repair
or modification may cause an electric shock or fire.
Do not let any foreign matter such as pin and a piece of metal
enter into the inside of the Product. In case this has occurred,
turn off the power switch immediately, and stop using it. If the
Product is used continuously without being reconditioned, an
electric shock or fire may result. Call your nearby SEIKO dealer
or agent for repair.
Never operate the Product with wet hands. An electric shock or
malfunction may result.
Do not expose the Product to splashes of water. An electric
shock, malfunction or fire may result.
Never use any damaged power cord or plug, or loose socket.
An electric shock or fire may result.
Do not use or keep the Product at following places, as this may
cause an electric shock, malfunction or fire:
・Places under extremely high temperatures (such as those
exposed to direct sunlight);
・Dusty places;
・Places exposed to frequent vibrations; and
・Places subject to static electricity.

- 2 -
CAUTION
Do not drop the Product, or hit it strongly against hard objects.
A malfunction or injury may result.
When connecting the Product with any accessory, optional or
other device, check that the connection is performed properly
and securely. A malfunction or failure may result.
Do not twist or pull strongly the cables to connect the Product
with the grip switch, or optional or other devices, or do not place
any heavy object on the cables. A malfunction of the Product or
break in them may result.
Install the dry batteries properly, checking that their (+) and (-)
terminals are properly aligned. A malfunction or failure may
result.
Do not use dry batteries of different types together. Otherwise,
heat generation or electrolyte leakage of the batteries may result
and cause damage to the Product.
Do not use old and new dry batteries together. Otherwise, heat
generation or electrolyte leakage of the batteries may result and
cause damage to the Product.
Use only dry batteries of the same make, type and size.
Otherwise, heat generation or electrolyte leakage of the
batteries may result and cause damage to the Product.
Use the dry batteries only within their specified operational
temperature range. The alkaline dry batteries, in particular,
should never be used in cold temperatures below the specified
range. Otherwise, they may not perform as specified, and a
malfunction of the Product may result.
If you decide not to use the Product for a long time, take out the
dry batteries. Otherwise, heat generation or electrolyte leakage
of the batteries may result and cause damage to the Product.
Please note that the AC cord (5m) enclosed with the AC adapter
can be used within Japan only.
When an external battery is used, use 11~14 V DC battery only.
A malfunction, fire or personal injury may result.
To feed the paper, be sure to operate the “FEED” button, and do
not pull the paper forcibly. This may damage the printer.
Do not turn off the switch while operating the Product.
Otherwise, the measurement data obtained so far will be
erased, and a malfunction or failure may result.
Do not expose the case of the Product to solvents such as
alcohol and gasoline, spray of cosmetics or the like, cleaners,
adhesives, or paints. They may discolor, deteriorate or
damage the case due to chemical change.

- 3 -
2. INTRODUCTION
2.1 Overview
The SEIKO Sports Printer CT-2000 is a multi-purpose printer/timer that can be used for various
sports events requiring timing such as track and road running races, swimming, ski and skate.
2.2 Features
zBeing equipped with various measurement modes, CT-2000 can be used for timing of all types
of sports events.
zTiming down to 1/1,000 of a second is possible.
The method of calculating the fraction of a second can be selected from 10 types including
rounding up, rounding down and rounding off, thus making it possible to comply with various
timing rules adopted in different sports events.
zA large-sized LCD monitor is used to make it easier to check various types of information
displayed on it. (20 characters x 4 lines)
zThe design of the grip switch is renewed so that it better fits into your palm and provides easier
switch operation.
zBy using resin case, high durability has been achieved.
zIf the dry batteries are installed when CT-2000 is powered by AC adapter, the power source
can be quickly switched over to the batteries in case of failure of AC power supply, to ensure
constant operation. *1
zTwo sets of dry batteries (6 AA size cells per set) can be installed in the main body, and the
power source is switched over automatically between them. By replacing the unused set of dry
batteries with new ones, CT-2000 can be powered by the dry batteries continuously for a long
time.*1
zRechargeable batteries can be used in place of alkaline dry batteries.*1
zCT-2000 can also be powered by external battery (DC11V～DC14V)*1
zThe Auto Measurement Mode enables the measurement during individual practices performed
alone.
・ Reaction time (start reaction time: time after the start signal until swimmer’s feet have left the
starting block), lap time, and split time can be measured during swimming practices.
・ Lap time and split time can be measured during practices of speed skating, track, and other
races.*2
・ By outputting a signal to an external buzzer device, CT-2000 can control the device to
generate a starting sound automatically.*2
zEven if the actual start time has differed from the scheduled time, the Time Correction Mode
(inputting time difference from start time) corrects the scheduled start time set in advance in the
secondary CT-2000 units, enabling them to synchronize with the master CT-2000 unit.
zThe Speed Measurement Mode measures the average speed over a given section of the entire
distance.*2
zBy connecting a Bib No. input device with CT-2000, the measured times can be printed out
together with the Bib No.*2
zCT-2000 can be connected with a personal computer via USB interface.
zTwo types of time signals (RS-422) are output to the scoreboard (with or without running time
data).
zA synchronization signal can be output to external devices.
zAs CT-2000 is compatible with CT-1000, the grip switches, extension unit, synchronization
cables, and cables to connect with scoreboard used previously with CT-1000 can also be used
with CT-2000 (with the exception of a cable used to connect with a personal computer).
*1: Dry batteries, rechargeable batteries and external battery are not included with CT-2000, and
they should be purchased separately if required.
*2: Optional device is required.

- 4 -
2.3 Lap Time and Split Time
Lap time: Time required to go a given section of the
entire distance.
Split time: Time required to go from the start to any
given point of the entire distance.
2.4 System Components
①CT-2000 main body 1 unit
②GS-51 grip switch (with 2.5 m cable) 2 units
③AC adapter (with 5 m cable) 1 unit
④RP-03 roll paper 1 roll
⑤ERC-22 ribbon cassette 1 unit (preset in printer section of main body)
⑥Operating Manual (this document)
CT-2000 Main Body
GS-51 Grip Switch
AC Adapter
RP-03 Roll Paper
ERC-22 Ribbon Cassette

- 5 -
2.5 How to Open the Case
Place the case with the side attached with a sticker
facing toward you, and unlock the four locks on the
upper and lower sides and two locks on the side
faces to open the case.
2.6 Power Supply
zCT-2000 can be supplied with the power from two sources. One is the power source connected
to @@@@@ (AC adapter or external battery), and the other is either of the two sets of dry
batteries.
zFor external battery, use 11~14 V DC battery only.
zRechargeable batteries can be used in place of alkaline dry batteries.
zWhen all types of power sources are available, the one connected to @@@@@ will be used.
zWhen CT-2000 is powered by the dry batteries, the LED lamp above the battery compartment
of the batteries in use lights up.
zWhen replacing the dry batteries with new ones, be sure to replace those in the battery
compartment whose LED lamp stays out.
zWhen the battery power of both sets of dry batteries has reduced to a low level, both sets are
used at the same time.
In that case, the LEDs of both battery compartments light up. Replace the batteries with new
ones set by set.
CAUTION
Install the dry batteries properly, checking that their (+) and (-)
terminals are properly aligned. A malfunction or failure may
result.
Do not use dry batteries of different types together. Otherwise,
heat generation or electrolyte leakage of the batteries may result
and cause damage to the Product.
Do not use old and new dry batteries together. Otherwise, heat
generation or electrolyte leakage of the batteries may result and
cause damage to the Product.
Use only dry batteries of the same make, type and size.
Otherwise, heat generation or electrolyte leakage of the
batteries may result and cause damage to the Product.
Use the dry batteries only within their specified operational
temperature range. The alkaline dry batteries, in particular,
should never be used in cold temperatures below the specified
range. Otherwise, they may not perform as specified, and a
malfunction of the Product may result.
If you decide not to use the Product for a long time, take out the
dry batteries. Otherwise, heat generation or electrolyte leakage
of the batteries may result and cause damage to the Product.
When an external battery is used, use 11~14 V DC battery only.
A malfunction, fire or personal injury may result.

- 6 -
3. NAMES AND FUNCTIONS OF PARTS
3.1 Battery Compartment
No. Name Function
①BATT.1
Open the battery compartment cover, and install the batteries.
②BATT.2
③LED The LED of the compartment of the batteries in use lights up.
3.1.1 How to Install the Batteries
①Put your finger on the protrusion of the battery compartment cover, and pull it up to open the
cover.
②Install the dry batteries while checking that their (+) an (-) terminals are properly aligned.
① ②
③ ③

- 7 -
3.2 Connector Section
No. Name Function
①PC DATA
Connect with a personal computer using a USB cable.
* For details, refer to【6.9 PC DATA (Output of Data to Personal
Computer)】on P. 50.
②DC12V IN
Connect AC adapter included with CT-2000 or an external battery.
After connection, be sure to fix the cable securely in the same manner
as you would turn the screw.
③AUX It is an unused connector (for extending functionality).
④BIB
Connect Bib No. input device.
After connection, be sure to fix the cable securely in the same manner
as you would turn the screw.
⑤EXT.BUZZER
Connect external buzzer device.
After connection, be sure to fix the cable securely in the same manner
as you would turn the screw.
⑥EXT.SIGNAL
Connect input extension unit.
The number of input channels can be increased to a maximum of 10.
After connection, be sure to fix the cable using the lock screw.
⑦DATA OUT Two types of time signals (RS-422) are output to the scoreboard.
After connection, be sure to fix the cable using the lock screw.
⑧CH1
By connecting a grip switch, etc., CH1 signal can be input.
Mate the protrusions of the plug and receptacle connectors with each
other, and push in the plug until it clicks fixed.
⑨CH2
By connecting a grip switch, etc., CH2 signal can be input.
Mate the protrusions of the plug and receptacle connectors with each
other, and push in the plug until it clicks fixed.
⑩START
An external start signal can be input.
Mate the protrusions of the plug and receptacle connectors with each
other, and push in the plug until it clicks fixed.
⑪SYNC Use the connector to synchronize other units of CT-2000.
For details, refer to【6.8 SYNC (Synchronization)】on P. 48.
②
①
③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪

- 8 -
3.3 Printer Section
No. Name Function
①
POWER
switch It turns on the power of CT-2000 main body.
②LOCK switch
It prevents mistaken operation of the operation buttons.
By sliding it to “ON” position, all the buttons except “FEED” button are
disabled.
* For details, refer to【6.7 LOCK Switch】on P. 47.
③Roll paper
It is a roll paper for use with the printer.
Be sure to use the one for exclusive use with CT-2000.
It is recommended that a new roll paper be installed when CT-2000 is
used for timing in a competition.
④Ribbon
cassette
It is an ink ribbon cassette for use with the printer.
Be sure to use the one for exclusive use with CT-2000.
It is recommended that a new ribbon cassette be installed when
CT-2000 is used for timing in a competition.
⑤Printer It prints out the measurement data during and after measurement.
* The above parts are all located inside the printer cover.
①
② ③
④
⑤

- 9 -
3.3.1 How to Install a Roll Paper
①Open the printer cover, turn on the POWER
switch, and take out the paper holder.
②Insert the edge of the paper into the paper inlet
of the printer.
③Press @@@ to feed the paper until the edge
of the roll paper comes out from the outlet.
CAUTION
To feed the paper, be sure to operate the “FEED” button, and
do not pull the paper forcibly. This may damage the printer.

- 10 -
④Insert the paper holder into the roll paper.
⑤Set the roll paper in position in the printer, and
close the printer cover.

- 11 -
3.3.2 How to Replace the Ribbon Cassette
* When the roll paper has been installed inside the printer, take it out temporarily before
replacing the ribbon cassette.
①Open the printer cover and then ribbon
cassette cover.
②Push the “PUSH” portion of the ribbon cassette
to remove it.
③Push in the new ribbon cassette until it clicks in
position.
④Rotate the ribbon feed roller in the direction of
the arrow with a finger to remove the slack of
the ribbon.

- 12 -
3.4 Monitor Section
No. Name Function
①BLOCK Block No. (up to 100) of the displayed memory block is indicated.
②DATA Data No. within the displayed block is indicated.
③MEMORY
During measurement, the total number of data stored in memory is
indicated.
During recall, the number of data stored in the selected block is
indicated.
④MODE Measurement Mode No. is indicated.
⑤TIME UNIT The measurement unit is indicated.
⑥BATT.1
Remaining power of each set of dry batteries is indicated.
⑦BATT.2
3.4.1 Memory
zCT-2000 can store up to 3,000 measurement data in its memory.
zThe measurement data is stored block by block, and up to 100 blocks can be stored.
zThe data stored in memory can be recalled for display on the monitor section and for
reprinting by the printer as many times as necessary, before it is erased or the POWER
switch is turned off.
zWhen the number of data stored in memory reaches 3,000, new measurement will be printed
out but will not be stored in memory for later recall.
When the bib No. input device is connected to CT-2000, new measurement will be neither
printed out nor stored in memory.
* For the method of clearing data in memory, refer to【6.6 How to Clear Data in Memory】on P.
46.
① ② ③
④
⑤
⑥
⑦

- 13 -
3.4.2 Memory Block
zThe measurement data obtained from the start of the timer until it is stopped and reset is
stored in memory as one block of data.
zThe block No. is assigned to each block automatically, and the data can be recalled and
reprinted by designating the corresponding block No.
zUp to 100 blocks can be stored in memory, and the block No. is assigned from “1” in the
order of measurement.
zWhen the block No. reaches 100, new measurement data will not be stored in memory.
zIf the timer is started but no measurement is made until it is stopped and reset, no data is
stored in memory, and the block No. will not be incremented.
(Example)
Total number of
data in memory 1・・・100 101・・・ 300 301・・・500 ・・・ ・・・3,000 (the last
data in memory)
Block No. 1 2 3 ・・・ 100 (the last block
in memory)
3.4.3 Measurement Mode
zEight types of measurement modes are available.
zThe number of the measurement mode currently in use is indicated on the monitor section.
Measurement
Mode No. Measurement Mode
1 Counting Mode
2 Parallel Counting Mode
3 Parallel Lap/Split Time Measurement Mode
4 Parallel Delayed Start Mode
5 Time Correction Mode (inputting time difference from start time)
6 Auto Measurement-1 Mode
7 Auto Measurement-2 Mode
8 Speed Measurement Mode
* For details, refer to【5. MEASUREMENT MODE】on P. 22.

- 14 -
3.4.4 TIME UNIT
z10 types of measurement increments are available.
zThe time unit No. of the measurement unit currently in use is indicated on the monitor
section.
zThe measurement data is stored in memory and printed out using the selected measurement
unit.
Time Unit No. Measurement unit
of stored/printed
data
Method of calculating fraction of a
second
0 1/1000s 1/1,000 second －
1 1/100s (discarding)
1/100 second
1/1000 sec. digit is discarded.
(1/1,000 sec. digit is rounded down.)
2 1/100s (raising)
1/1000 sec. digit is discarded, and
1/100 sec. digit is raised by one.
(1/1,000 sec. digit is rounded up.)
3 1/100s (rounding off) 1/1,000 sec. digit is rounded off.
4 1/10s (discarding)
1/10 second
1/100 sec. and lower digits are
discarded.
(1/100 sec. digit is rounded down.)
5 1/10s (raising)
1/100 sec. and lower digits are
discarded, and 1/10 sec. digit is
raised by one.
(1/100 sec. digit is rounded up.)
6 1/10s (rounding off) 1/100 sec. digit is rounded off.
7 1s (discarding)
1 second
1/10 sec. and lower digits are
discarded.
(1/10 sec. digit is rounded down.)
8 1s (raising)
1/10 sec. and lower digits are
discarded, and 1 sec. digit is raised
by one.
(1/10 sec. digit is rounded up.)
9 1s (rounding off) 1/10 sec. digit is rounded off.
3.4.5 BATT.1, BATT.2 (Remaining Power)
zThe remaining power of the dry battery sets @@@@@@@@@@is indicated.
Indication
on monitor Remaining Battery Power
H The batteries have sufficient power.
M The batteries near to their end.
L Replace the batteries with new ones.
x The battery power has depleted completely, or no battery
is installed.

- 15 -
3.5 Operation Section
No. Name Function
①M MASTER Pressing it alone will not work.
It works when being pressed simultaneously with another button.
②
M START By pressing this button while keeping “MASTER” pressed, the timer starts.
CH1 Press this button alone to input CH1 signal.
③
M STOP By pressing this button while keeping “MASTER” pressed, the timer stops.
CH2 Press this button alone to input CH2 signal.
④
M RESET By pressing this button while keeping “MASTER” pressed, the timer is reset.
CH3 Press this button alone to input CH3 signal.
⑤M CLEAR
By pressing this button while keeping “MASTER” pressed, the display to
clear data in memory appears.
* For details, refer to【6.6 How to Clear Data in Memory】on P. 46.
⑥UP
By pressing this button while keeping “MASTER” pressed in the Time
Correction Mode, the time difference from the scheduled start time can be
input.
* For details, refer to【5.5 Time Correction Mode (Measurement Mode No.
5】on P. 30.
Use this button to set items. (Increasing or advancing the value)
⑦DOWN Use this button to set items. (Decreasing or moving back the value)
① ② ③ ④ ⑤
⑥
⑦
⑧ ⑨
⑩
⑪ ⑫
⑬

- 16 -
No. Name Function
⑧
M RECALL
By pressing this button while keeping “MASTER” pressed, the mode
changes to “Recall”.
* For details, refer to【6.4 Memory Recall】on P. 44.
LEFT When setting items, press this button to move the cursor to left.
⑨
M
REPRINT
By pressing this button while keeping “MASTER” pressed, the mode
changes to “Reprint”.
* For details, refer to【6.5 Reprinting Data in Memory】on P. 45.
RIGHT When setting items, press this button to move the cursor to right.
⑩SET When setting items, press this button to register the setting you have
made.
⑪CANCEL
By pressing this button while keeping “MASTER” pressed, the display to
select measurement mode appears.
* For details, refer to【4. SETTING PROCEDURE】on P. 17.
When setting items, press this button to cancel the setting you have
made.
⑫REPRINT
STOP
Press this button to stop printout while reprinting data.
* For details, refer to【6.5 Reprinting Data in Memory】on P. 45.
⑬FEED Press this button to fee the paper.
* By sliding LOCK switch to “ON” position, all the buttons except “FEED” are disabled.
For details, refer to【6.7 LOCK Switch】on P. 47.