Seitron freetime evo User manual

WIST03250ESE 040216 191022
Quick guide
Kit freetime evo radio
Wireless programmable thermostat kit
WARNING!
THE DEVICES IN THIS KIT HAVE BEEN FACTORY PRE-MATCHED: ONCE THE MECHANICAL INSTALLATION IS
DONE, THEY ARE READY FOR USE.
Go to the site www.seitron.com
and dowload the complete manual
CONTACT US
customer[email protected]
TALK WITH US
[phone]
radio RECEIVER
TECHNICAL FEATURES
Power supply: 230V 50Hz/ 24V Thermoregulation class: IV (2%)
Outputs: 6(4)A 250V (voltage free contacts) Software class: A
Type of action: 1 Ball pressure test temperature: 75°C
Pollution degree 2 Rated impulse voltage: 2500V
EMC test voltage: 230V 50 Hz Size: 78x125x30,5 mm
EMC test current: 45mA (LxAxP)
INSTALLATION
WARNING!
- Before wiring the appliance be sure to turn the mains power off.
- Before proceeding with the installation of the receiver, make sure that the radio signals transmitted by the thermostats are
correctly received by the receiver.
- Installationandelectricalwiringsofthisappliancemustbemadebyqualiedtechniciansandincompliancewiththecurrent
standards.
1Cut off mains power.
Using a screwdriver, push the plastic flap of the bottom slot and
slightly lift the cable lid up.
2Fig. 1
Push for 3 sec. Conrm Store
Set time Set minutes
Clock setting
WARRANTY
Regarding the continuous development of its products, the manufacturer reserves the right to make changes in technical data
and performance without prior notice. The consumer is guaranteed against product conformity defects according to European
Directive 2019/771 EU as well as the manufacturer’s warranty policy document. The full text of the warranty is available from the
seller upon request.
Conrm
Comfort temperature setting
Economy temperature setting
Conrm
Setting the set point temperature
Each time the or key is pressed,
the time cursor automatically moves to the
next half hour.
Select time
or
Set Comfort temp. Set Economy temp.
Comfort Store
Economy
Time program setting

Rotate the cable lid and remove it completely.
3
Fix the plate onto the wall using the two screws housings with
a 60 mm centre-to-centre distance (use the screws and/or
dowels supplied) - Fig. 5.
WARNING!
The receiver must be installed on a wall or on a surface in or-
der to make the back of the product inaccessible.
5
Placethecablelidonthebaseandrotateittowardsthebase;pushthecableliduntilthelockingplasticapspringsinto
the hole on the lower side of the cable lid (Fig. 1).
Power the receiver back on.
7
8
PROGRAMMABLE THERMOSTAT freetime evo radio
TECHNICAL FEATURES
Power supply: Battery 2x1.5V size AA. Software class: A
Size: 134x86x36 mm (LxHxD) Thermoregulation class: IV (2%)
INSTALLATION
Unhook and remove the front cover of
freetime evo radio, from its plastic base
underneath, applying pressure on the
2 clips located on the bottom side of
freetime evo radio and lifting the cover
towards the upper side.
2
3
Connect the remote temperature probe (Optional).
4
Access the battery compartment, by sliding towards left the cover.
Fix freetime evo radio body to the base using the provided screw that has its
dedicated hole inside the battery compartment.
6
Set the main parameters in order to operate freetime evo radio (Time - Temperature - Schedule Program).
Insert the batteries in the battery compartment, respecting polarities.
7
8
Fig. 2
Fig. 5
83 mm
Fix the base of freetime evo radio to the wall using the provided screws,
taking care to pass the wires through the special openings.
Place back the plastic case of freetime evo radio by first hooking it to the
upper side of the plastic base (1) and then locking it to the lower side clips (2).
5
2
1
1
4There are three options for the cable entry:
Back cable entry: Open the hole EFig. 4, with a screwdriver.
Side cable entry:By using suitable pliers, remove the plastic teeth, as
indicated by arrows in DFig. 3.
Bottom cable entry: Open one or both holes FFig. 4, with a screwdriver.
DD
Fig. 3
Fig. 4
F F
E
6
BOILER 230Vac
50Hz
21 LN
N
CC 3
N
O
Make electrical connections following the “Electrical Connections” chapter of the
complete manual.
Asimpliedconnectiondiagramisshownontheside:
Power supply:
L N: Power supply 230V 50Hz (Neutral on terminal N)
Relay contacts:
NO: Normally open contact
NC: Normally closed contact
C: Common
Fig. 6
a
1Cut off mains power.