Sencor SSS 1400 User manual

SSS 1400
EN User Manual Party Wireless Waterproof Speaker
CZ Uživatelská příručka Párty bezdrátový voděodolný reproduktor
SK Používateľská príručka Párty bezdrôtový vodovzdorný reproduktor
HU Felhasználói kézikönyv Vezeték nélküli vízálló parti hangszóró
PL Podręcznik użytkownika Bezprzewodowy głośnik wodoodporny

EN – 2
SAFETY INSTRUCTIONS
This product has been designed with the utmost safety in mind. However, incorrect
use may lead to electric shock or re. This is why users should observe the following
instructions when using this device.
This device uses a semiconductor unit and contains no user serviceable parts. Do
not disassemble this device, otherwise you are exposed to the risk of electric shock.
If any damage to this product occurs, please have this product repaired by a qualied
service technician.
Power
Power supply of this unit must be match the serial plate data.
Heat source
Keep this unit out of heat sources like stove or direct sunlight.
Cleaning
Prior to cleaning, please disconnect power rst. For cleaning, don’t use liquid
detergents or caustic liquids - just clean the unit with a soft cloth.
Heavy objects
Do not place heavy objects on the unit, otherwise damage might occur.
Connecting other devices
Before connecting other devices to this unit, please make sure to disconnect power.
Otherwise damage to the unit or personal injury might occur.
Faults to be repaired
If any of the following problems occurs, please disconnect power to the unit and
contact a qualied service technician.
A. Power cord or plug is damaged.
B. Liquids or other foreign objects have penetrated inside the product.
EN User Manual Party Wireless Waterproof Speaker

EN – 3
C. If the unit does not work even if it’s being operated according to the instructions,
don’t press any buttons other than those described in these instructions.
Otherwise, damage to this unit may occur along with a more demanding repair.
D. This unit has fallen on the ground from a big height.
E. Burns can be smelled from the product inside.
Maintenance
If you don’t have enough technical knowledge necessary to maintain this unit, don’t
attempt to repair it by yourself. By removing the cover, you are exposed to a risk of
electric shock. If needed, please contact a qualied service technician.
Replacement of parts
If you need to replace any part of this unit, ask your service technician to make
a replacement for equal spare part models. If other spare part models are used for
replacement, serious damage, electric shock or shortening the unit’s lifetime may
occur.
Safety check
After completing maintenance, ask your service technician to perform an on-site
safety check to ensure that the unit is operating safely.
Note:
Before using this product, read these instructions carefully and keep it well for future
use.

EN – 4
INCLUDED CONTENTS
1x BT speaker
1x USB-C charging cable
1x User’s manual
BT SPEAKER DESCRIPTION

EN – 5
1 LED indicator
2On and o󰀨 button / change mode / turn o󰀨 and on BT speaker
announcements
3 USB-A for playback from memory device
4 Charging socket (USB-C)
5“+” previous track, volume down, go to higher FM station button
6PLAY / PAUSE / FM station search button
7“-” previous track, volume down, go to lower FM station button
SLeft and right channel (MONO)
B Passive emitter (rear side)
MIntegrated microphone

EN – 6
PUTTING INTO OPERATION
Before rst use, be sure to read the safety instructions contained in this
user's manual carefully.
Before rst use, please charge the BT speaker to a maximum level. Press and
hold the “on/o󰀨” button to turn on the BT speaker. Turning on and o󰀨 is indicated
by a sound signal. To turn the BT speaker o󰀨, press and hold the “on/o󰀨” button.
Changing the source of the music being played is done by briey pressing the “on/o󰀨”
button when the power is on.
Attention: After a longer period of inactivity, the appliance will turns itself o󰀨.
PAIRING DEVICES VIA BLUETOOTH
Turn on the BT speaker and search for its Bluetooth name “SSS 1400” in the device
to be paired, then start the pairing process. If you are requested to enter a pairing
code while your device and the BT speaker are pairing, use the code: “0000”. To
disconnect the paired device, end the pairing session on your mobile device or long
hold the “Play / Pause” button. Disconnection will be indicated by an acoustic signal.
Note: To ensure a stable Bluetooth connection, make sure that the distance between
the BT speaker and your connected device is kept within 10 meters.
TWS FUNCTION
If you purchase another speaker (“SSS 1400”), you can pair them together for optimal
stereo sound. Switch on both BT speakers, press and hold the + and - “volume down
and up” buttons on one of the BT speakers together and wait until the BT speakers
are connected. Connecting both BT speakers may take some time depending on
searching for the slave BT speaker. You will be informed of a successful pairing by
the voice signal "True wireless paired". Then connect your mobile device to the BT
speaker. Changing the volume level will automatically a󰀨ect both paired BT speakers
simultaneously. To exit TWS mode, press and hold the + and - “volume down and up”
buttons together until the message “True wireless disconnected” appears.

EN – 7
Caution: The TWS function is only available in the Bluetooth mode. The connected
microphone will transfer voice only into the BT speaker to which it’s connected. It is
not possible to pair the device with another type of BT speaker with TWS function,
even within a re-edition of products with a di󰀨erent Bluetooth name.
RESET BUTTON
To reset the BT speaker, press and hold the “on/o󰀨” button until the BT speaker turns
o󰀨. Then switch on the BT speaker using the power button.
RECOMMENDATION: If there is an unexpected problem with the BT speaker
connection or function, reset the BT speaker.
PLAY/PAUSE BUTTON
In the music being played: Press the “Play / Pause” button to start or pause music
playback during Bluetooth connection or while a USB memory media is inserted.
In the FM mode: Press the button to start the autoscan function (search for available
FM stations).
Incoming calls: An incoming call will be accompanied by an acoustic signal. Press
the button to answer/end the call.
VOLUME AND TRACK PLAYBACK CONTROL
The volume of the BT speaker is controlled using the + and - “volume down and up”
buttons on the BT speaker. During playback of songs from the storage media, you
can skip to the next song by pressing and holding the “+” button.
To select the previous track, press and hold the “-” button. In FM mode, long press
the button to go to next “+” / previous “-” FM station.

EN – 8
PLAYBACK FROM USB STORAGE MEDIA
USB-A playback
Insert the USB storage disc with supported audio content in the USB slot. The USB
source activates automatically and playback begins. Or, press “change mode” briey
to select “USB mode”. The music playback from the connected storage will start
automatically. Upload your music to the storage in the order in which it will be played
by the BT speaker.
Attention: Due to a number of devices on the market, compatibility and playback
support are not guaranteed for all media. The memory devices you want to connect
should be tested in advance and/or formatted as FAT32 le format. The playback of
protected media, les or content stored inside them may fail.
USB-A does not have a power bank function – it is not used to charge mobile
devices.
FM RADIO
Press the “change mode” to switch the BT speaker to FM radio mode.
Long press the „PLAY / PAUSE / FM station search“ button to start the FM station
scan.
Once the stations are found and stored into the BT speaker’s memory, you can
switch between the stations found by holding down the “+” / “-” button (the next/
previous stations in sequence).
Note: For best reception, place the device in an open area where the FM band will
not be inhibited.
TO DISABLE BT SPEAKER NOTIFICATION AND
MESSAGES
Press the “on and o󰀨” button 3 times to turn notications and alerts o󰀨 or on. When
turned o󰀨 and on, the BT speaker will remember the last selected mode.

EN – 9
Caution: in the o󰀨 state, no messages notifying about the BT speaker state will be
shown. Charge the BT speaker as a preventive measure. Avoid using the sound at
a maximum level.
CHARGING THE BT SPEAKER
A charged battery provides power for several hours of operation at normal volume
levels. A high volume consumes more battery power; therefore, we recommend
listening at normal volume levels. To charge the BT speaker, please connect the
charging adapter to the mains and then to the BT speaker.
Use your own 5V, 1A charging adapter. The battery status indicator will indicate
charging in orange continuously during charging. A low battery level will be indicated
by an audible alert.
Attention: For charging, use only the original accessories supplied with the
appliance. To achieve the maximum battery lifetime, it is best not to start charging
until the low battery audible alert is output. Charge continuously until fully charged.
When the battery operating time becomes very short, the battery lifetime has been
used up; we recommend that you have the battery replaced at your authorized
centre.
Recommendation: If the unit is not to be used for an extended period of time,
we recommend to fully charge the battery once every two to three months. We
recommend to store the unit with a the battery charged to prevent irreparable
damage to the battery (loss of capacity).
INGRESSION PROTECTION (IPX6)
The device is waterproof, allowing you to listen to music near water.
Ingression Protection IPX6 Protected against intense water spray. Water is coming
from a 12.5mm jet at all angles at a ow rate of 100 litres per minute and a pressure
of 100 kN/m2per square meter for at least 3 minutes from a 3m distance.

EN – 10
Caution: Always remember to seal the BT speaker inputs (No. 3–4 in the picture
“BT speaker description”) with the original gasket and make sure that the gasket is
not damaged. Never charge the unit during possible contact with uids. The unit is
designed for contact with clean water only without any additives. Avoid exposing the
unit to contaminated or industrially treated uids (such as lemonade, sea/salt water,
oils, etc.).
TECHNICAL SPECIFICATIONS
SSS 1400
Water-resistant bluetooth speaker with IPX6 protection class
Features:
Water-resistant speaker with IPX6 protection class
The speaker cover is made of premium fabric
TWS function (True Wireless Stereo)
Sound:
Maximum speaker output 5 W (Impedance: 3 Ω)
1 speaker + 1 passive radiator
Frequency response: 80Hz–16kHz
Total harmonic distortion: ≤ 10%
Inputs:
Bluetooth Audio 5.1
Playback from USB (up to 32GB / MP3)
Other:
FM PLL radio
Handsfree Function
Built-in rechargeable battery: 1,800 mAh Li-Ion
Playback time of up to 25 hours (@ 50% volume)
USB-C charging
Max. charging time 4 hours
Accessories: USB charging cable, user’s manual

EN – 11
Dimensions: 99×76×50mm
Weight: 200g
FM radio Band range 87.5 MHz – 108 MHz
Bluetooth Version 5.1
Maximum Transmitter Power 100mW @ 2.4GHz–2.4835GHz
Codec SBC
Proles A2DP/AVRCP/HFP

EN – 12
INSTRUCTIONS AND INFORMATION ON THE DISPOSAL OF DISCARDED
PACKAGING MATERIALS
Take the packaging material to a collection yard for disposal.
DISPOSAL OF DISCARDED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on the product, accessory or packaging indicates that
the product must not be treated as normal household waste. Please
dispose of this product in a collection yard designated for the recycling
of electrical and electronic equipment. In some EU countries or in some
European countries, you can return your products to your local retailer
when you buy an equivalent new product. Correct disposal of this product
helps save valuable natural resources and prevents possible adverse
impacts on the environment and human health that might be caused
by improper waste disposal. Please contact your local authority or the
nearest waste collection yard for further details. Improper disposal of this
type of waste may be subject to a legal ne.
For companies in the European Union
If you need to dispose of electrical or electronic equipment, ask your
dealer or supplier for the necessary information.
Disposal in countries outside the European Union
To dispose of this product, please ask your local authorities or dealer for
the necessary information on correct disposal.
This product complies with EU requirements.
FAST ČR, a.s. hereby declares that the radio device type SSS 1400 conforms to the
2014/53/EU directive. The full text of the EU Declaration of Conformity is available at:
www.sencor.eu.

EN – 13
Changes in the text, design and technical specications may be made without prior
notice and we reserve the right to make such changes.
The original version is in Czech.
Manufacturer’s address:
FAST ČR, a. s., U Sanitasu 1621, Říčany CZ-251 01

EN – 14
EN Warranty conditions
Warranty card is not apart of the device packaging.
This product is warranted for the period of 24 months from the date of purchase to the end-user. Warranty
is limited to the following conditions. Warranty is referred only to the customer goods using for common
domestic use. The claim for service can be applied either at dealer’sshop where the product was bought, or
at below mentioned authorized service shops. The end-user is obligated to set up aclaim immediately when
the defects appeared but only till the end of warranty period. The end user is obligated to cooperate to certify
the claiming defects. Only completed and clean (according to hygienic standards) product will be accepted.
In case of eligible warranty claim the warranty period will be prolonged by the period from the date of claim
application till the date of taking over the product by end-user, or the date the end-user is obligated to take it
over. To obtain the service under this warranty, end-user is obligated to certify his claim with duly completed
following documents: receipt, certificate of warranty, certificate of installation.
This warranty is void especially if apply as follows:
Defects which were put on sale.
Wear-out or damage caused by common use.
The product was damaged by unprofessional or wrong installation, used in contrary to the applicable
instruction manual, used in contrary to legal enactment and common process of use or used for another
purpose which has been designed for.
The product was damaged by uncared-for or insufficient maintenance.
The product was damaged by dirt, accident of force majeure (natural disaster, fire, and flood).
Defects on functionality caused by low duality of signal, electromagnetic field interference etc.
The product was mechanically damaged (e.g. broken button, fall).
Damage caused by use of unsuitable media, fillings, expendable supplies (batteries) or by unsuitable
working conditions (e.g. high temperatures, high humidity, quakes).
Repair, modification or other failure action to the product by unauthorized person.
End-user did not prove enough his right to claim (time and place of purchase).
Data on presented documents differs from data on products.
Cases when the claiming product cannot be indentified according to the presented documents (e.g. the
serial number or the warranty seal has been damaged).
Manufacturer:
FAST ČR, a.s., U Sanitasu 1621, Říčany 251 01, Czech Republic
Visit www.sencor.com for detailed information about authorized service centers.
The original version of the instructions is in the Czech language, other language versions are made by the
appropriate translation.