Seneca Z201-H User manual

USA ENGLISH - 1/4
MI00141 -E2
Z201-H
ACCURRENT TRANSMITTER
5 AAC or10AAC full scale currentinput
0-20 mA or 4-20 mAoutput with active or passive connection;
0-10 VDC, 2-10 VDC, 0-5 VDC, or 1-5VDC
SettablebyinternaljumperandDIP-switch
Highprecision:0.3% FS
Powersupplypresenceindicationonfrontpanel
3-way isolation: 4000 VAC between power supply / input and output
GENERAL SPECIFICATIONS
The Z201-H current converter measures the simple harmonic
alternating current applied at the input and generates a standard mA or
V signal directlyproportionaltothecurrentmeasured.
BLOCK DIAGRAM
INPUT OUTPUT
CAT III 300 V
TECHNICAL SPECIFICATIONS
Power Supply:
Consumption:
Current Input:
85-265VDC orVAC from50to400 Hz;
Isolation: input/output:4000VAC
< 2 W at full load; < 20 mA @ 230 VAC
Power Supply Specifications
Input Specifications
Alternating Current: 0-5 AAC or 0-10 AAC,
Selectable by terminal wiring.
EN
9
8
7
13
Power supply
4
5
6
0 V
20 V
mA
output
V
output +
+
mA
output
+
ext. supply
max 28 V
85-265 V
AC/DC 50 to 400 Hz

MI00141 -E2 USA ENGLISH - 2/4
Current Output:
Voltage Output:
20Hz to 1kHz
4000VAC powersupply/output
CATIII 300 V,forinstallationon3-phaselinesupto500VAC
ph-ph, 300VAC ph-n.
Active or passive: 0-20 mA or 4-20 mA selectable by internal
jumperandDIP-switch.
Maximumloadresistance:600Ω. Protection:400W/ms.
AvailableVoltage:<21V.
Maximumapplicableexternalvoltage(ifpassiveoutput):28V.
Isolation:powersupply/input 4000VAC
0-5 V, 1-5 V, 0-10 V or 2-10 V selectable byinternaljumper
andDIP-switch.
Minimumloadresistance:2500Ω.Protection:400W/ms
Isolation: power supply / input 4000 VAC
Output Specifications
Precision @ 25ºC (1)
20-400 Hz (3)
400-1000 Hz (3)
Thermal Stability:
Response Time:
Operating conditions:
LED signal:
Protection degree:
Weight, Dimensions:
0.2 % om
0.4 % om 0.1 % ots 0.2 % ots < 0.1 % ots < 0.1 % ots
Other (2)
200 ppm/K.
For a stepped variation: max 100 ms from 10 to 90 %.
Temperature: -10 to 65°C, humidy 30-95 % @ 40°C
not-condensing.GroupIII.
StorageTemperature:-20 to 85°C
Altitude:upto2000meters a.s.l.
Presence of power supply (green)
IP20.
140 g, 100 x 112 x 17.5 mm
(1):Theseacronymsapply:om=ofmeasurement, ots=ofthescale.
(2):Errorcausedbyelectromagneticdisturbances(EMI).
(3): The precision values are indicated for a sinusoidal signal with distortion of < 1%, on current
reading4-20mA;errors ontheotheroutputscalesareincreasedasfollows:by0.1%forzerooffset
(0mA,0V),by0.1%onfs5Vandby0.15%onfs10V.
Theprecisionindicatedinthetablecan,onrequest,beprovidedonanotherspecifiedscale.
RememberthattheinstrumentindicatestheaverageadjustedvalueinrelationtotheRMSvalue.
Other Specifications
Precision Specifications
EN60688/1997+A1+A2
EN61000-6-4/2002-10 (electromagnetic emission, industrial
environment)
EN61000-6-2/2006-10 (electromagnetic immunity, industrial
environment)
EN61010-1/2001(safety)
Standards:
Frequency
Isolation:
Overvoltage
measurementClass:

MI00141 -E2 USA ENGLISH - 3/4
SW1
Internal Jumper J1
INSTALLATIONREQUIREMENTS
The module is designed to be installed on a DIN 46277 rail, and wired only by the
front terminals.
We suggestyou to installthe instrument verticallyinorder toallow ventilationofthe
module. Do notinstall anyobjectsorwire channels thatcan obstruct the ventilation
louvers.Avoid installing modules aboveequipmentthatgenerates heat. Install in the
bottomofthepanelorcompartment.
DIP-SWITCH AND INTERNAL JUMPER POSITION
OUTPUT SIGNAL SETTINGS
TheZ201-Hinstrumenttransmitsavoltageoracurrentsignal.
The output type (voltage or current) is set using the internal jumper, accessible under
the rear side of the the case.
Thesignalrange is setusing thedoubleDIP switchSW1.
Current or Voltage Output Selection
Current Output :(F) Voltage Output:
SW1SW1
J1
J1
Output Range Settings
Switch 1 Position Scale
SW 1.10 - OFF The full scale of the voltage output is .5 V
1 - ON (F) The full scale of the voltage output is .10 V
SW 1.20 - OFF The start of scale offset is disabled (0-20 mA, 0-5/10 V scale).
1 - ON (F) The start of scale offset is enabled (4-20 mA, 1-5 o 2-10 V
(F) : Factory settings.
(F) : Factory settings.

MI00141 -E2 USA ENGLISH - 4/4
Output Connection
Input for In < 10 A Input for In < 5 A
Applied Current
Input Connection
7
8In 7
9In
ELECTRICAL CONNECTIONS
We recommend using shielded cables for signal connections; the shield must be
connected to a instrument earth connection. We also recommend never positioning
these wires near power cables such as those for inverters, motors, or induction ovens,
etc.
Power Supply Connection
Thepowersupplyvoltagemustbeintherangeof 85-265VAC/VDC.
Theupperlimitsmustnotbeexceededasthiscanseriouslydamagethemodule.
Thepowersupplysourcemustinclude a fuse or suitable limiting device to protectfromany
failuresinthemodule.
6
5
V
4
5
5
ext. supply
max 28 V
6
AA
Voltage External Power Supply
When connected to a
current transformer,
one of the two wires
must be grounded.
Power supply
1
3
85-265 VDC/AC
50-400 Hz
Max 2 W
Disposal of Electrical & Electronic Equipment (Applicable throughout the European Union and other
Europeancountrieswithseparatecollectionprograms)
Thissymbol,foundonyourproductoronitspackaging,indicatesthatthisproductshouldnotbetreatedas
household waste when you wish to dispose of it. Instead, it should be handed over to an applicable
collection point for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences to the environment and
humanhealth,whichcouldotherwisebecausedbyinappropriatedisposalofthisproduct.Therecyclingof
materialswillhelptoconservenaturalresources.Formoredetailedinformationabouttherecyclingofthis
product, please contact your local city office, waste disposal service or thè retail store where you
purchasedthisproduct.
SENECA s.r.l.
Via Austria, 26 - 35127 - PADOVA - ITALY
Tel. [phone] - Fax [phone]
e-mail: [email protected] - www.seneca.it
This document is property of SENECA srl. Duplication and reproduction are forbidden, if not authorized. Contents of
the present documentation refers to products and technologies described in it. All technical data contained in the
document maybemodifiedwithoutpriornotice.Contentofthisdocumentationissubjecttoperiodicalrevision.