Sennheiser SI 1015-4000 SINGLE Dimensions

General Description
Sennheiser offers system packages that include all components necessary
to configure a complete system. Sennheiser’s Large-Area Infrared Systems provide
coverage of 4,000 sq. ft. up to 12,500 sq. ft. in both single and dual channel
modes. The SI1015 modulator and SZI1015 or SZI1029 emitters are the primary
components of the systems. The NT1015-120 will provide power for the SI1015
modulator and up to two SZI1015 or SZI1029 emitters. The SZA1060 terminat-
ing resistor (50 ohm), for the last emitter in a daisy chain, is included for system
designs that incorporate daisy chaining of emitters. The GA1031-CC rack adapter
allows for easy mounting of a SI1015 modulator to a 19" rack. The WM1 wall/
ceiling mount easily mounts the SZI1015 or SZI1029 emitter panels. The RI250
stethophone infrared receivers are for use with single channel systems operating at
2.3MHz,andincludetheBA151rechargeablebattery. Alternatively,fordualchannel
systems, the HDI302 stethophone infrared receiver is for use with systems
operating at 2.3/2.8 MHz, and also includes the BA151 rechargeable battery. The
BA151 rechargeable batteries can be conveniently recharged with the L151-10
charging unit(s) with the NT92-120 power supply. In addition, the NT2013-120
will power two to five L151-10 charging units.
Wireless | Systems
System Includes:
(1) SI1015—Two channel modulator
(1) NT1015-120—29 V DC power supply
(1) GA1031-CC—Rack adapter
(1) SZI1015—Emitter panel
(1) WM1—Wall/ceiling mount
(5) RI250—Single channel infrared stethophone receiver
(1) L151-10/NT—Charging unit with power supply
(1) NT92-120—AC adapter for L151-10 charging unit
SI1015-4000 Single System Package
* Illustrations do not show NT1015-120 power supply, GA1031-CC rack
adapter, NT92-120 adapter
Audio Input B
(XLR-3F)
Audio Input A
(XLR-3F)
DC Input Socket
(For NT1015-120)
RF Output 2
(BNC)
RF Output 1
(BNC)
Cable Grip
Strain Relief
RF Output
Termninal 1
DC Output
Termninal 1
DC Output
Termninal 2
RF Output
Termninal 2 Level Control A
Level Control B
Channel Selector Switch
IR Monitoring Diodes
49.817"
(1265.35 mm)
7.000"
(177.80 mm)
3.620"
(91.95 mm)
2.360"
(59.94 mm)
Power Supply
NT1015–120
9.040"
(229.62 mm)
6.660"
(169.16 mm)
10.350"
(262.89 mm)
9.680"
(245.87 mm)
ON/OFF
Switch
1.688"
(42.88 mm)
Power Cord
72.000"
(1828.80 mm)
Convection Cooling Fins
4.970"
(126.24 mm)
10.270"
(260.86 mm)
3.318"
(84.28 mm)
RF Output (BNC)
RF Input (BNC)
MONO/Multi Switch
5/8" Thread for mounting
(3/8" X 1/2" Adapters included)
RF Input Terminals
DC Input Terminals
DC Output Terminals
RF Output Terminals
IR Transmission Diodes
(behind cover)
Adjusting
Knob
Ratchet Adjustment
For Angle 5/8" External
Thread
4.571"
(116.10 mm)
ø1.936
(49.17 mm)
2.724"
(69.19 mm)
ø.161
(4.09 mm)
ø.743
(44.27 mm)
Mounting Plate
ø.1242
(31.55 mm)
5.286"
(134.26 mm)
Replaceable
ear cushions
Two IR
Receiving Diodes
(behind plastic cover)
7.390"
(187.71 mm)
1.467"
(37.26 mm)
Inserted BA151
Rechargeable
Battery
ON/OFF
Volume
Control
ø.752
(19.10 mm)
74.000"
(1879.60 mm)
13.000"
(330.20 mm)
2 Pin Texas Connector
NT92–120 Power Supply
LED Indicator
Trickle Charge
(Green)
Button:
Press to begin
10 HR charge cycle
LED Indicator
Charge (Red)
Charging for
RI250, HDI302
Infrared Receivers
(Up to ten)
1.500"
(38.10 mm)
LED Indicators
Bright=Normal charge
Dim=Trickle charge
Charging for
BA151 Battery
(Up to ten)
5.450"
(138.43 mm)
SI1015
SZI1015
WM1
L151–10NT
RI250
SI1015–Rack mountable, half rack, two channel modulator. Operates at
2.3/2.8 MHz. NT1015-120 power supply required.
SI1015
Audio Input B
(XLR-3F)
Audio Input A
(XLR-3F)
DC Input Socket
(For NT1015-120)
RF Output 2
(BNC)
RF Output 1
(BNC)
Cable Grip
Strain Relief
RF Output
Termninal 1
DC Output
Termninal 1
DC Output
Termninal 2
RF Output
Termninal 2 Level Control A
Level Control B
Channel Selector Switch
IR Monitoring Diodes
49.817"
(1265.35 mm)
7.000"
(177.80 mm)
3.620"
(91.95 mm)
2.360"
(59.94 mm)
Power Supply
NT1015–120
9.040"
(229.62 mm)
6.660"
(169.16 mm)
10.350"
(262.89 mm)
9.680"
(245.87 mm)
ON/OFF
Switch
1.688"
(42.88 mm)
Power Cord
72.000"
(1828.80 mm)
SI1015-4000
Single
CBinder - Information Systems.indd 13 11/11/08 11:49:27 AM

SZI1015-NT
SI1015-4000 Single System Package
49.817"
(1265.35 mm)
7.000"
(177.80 mm)
2.360"
(59.94 mm)
Power Supply
NT1015-120
Stripped Cable for
Connection to Barrier
Strip of SZI1015T
3.620"
(91.95 mm)
Convection Cooling Fins
3.318"
(84.28 mm)
10.270"
(260.86 mm) IR Transmission Diodes
(behind cover)
4.970"
(126.24 mm)
DC Input Terminals
DC Output Terminals
RF Output Terminals
5/8" Thread for mounting
(3/8" X 1/2" adapters included)
72.000"
(1828.80 mm)
Power Cord
49.817"
(1265.35 mm)
7.000"
(177.80 mm)
2.360"
(59.94 mm)
Power Supply
NT1015-120
Stripped Cable for
Connection to Barrier
Strip of SZI1015T
3.620"
(91.95 mm)
Convection Cooling Fins
3.318"
(84.28 mm)
10.270"
(260.86 mm) IR Transmission Diodes
(behind cover)
4.970"
(126.24 mm)
DC Input Terminals
DC Output Terminals
RF Output Terminals
5/8" Thread for mounting
(3/8" X 1/2" adapters included)
72.000"
(1828.80 mm)
Power Cord
WM1–Wall/ceiling mount with 5/8" thread for mounting 2 or more
SI30 or SZI30.
WM1
Adjusting
Knob
Ratchet Adjustment
For Angle 5/8" External
Thread
4.571"
(116.10 mm)
ø1.936
(49.17 mm)
2.724"
(69.19 mm)
ø.161
(4.09 mm)
ø.743
(44.27 mm)
Mounting Plate
ø.1242
(31.55 mm)
RI250–Single channel infrared stethophone receiver for use with infrared
systems operating at 2.3 MHz. Includes one BA151 rechargeable battery.
(1.6 oz)
RI250
5.286"
(134.26 mm)
Replaceable
ear cushions
Two IR
Receiving Diodes
(behind plastic cover)
7.390"
(187.71 mm)
1.467"
(37.26 mm)
Inserted BA151
Rechargeable
Battery
ON/OFF
Volume
Control
ø.752
(19.10 mm)
L151-10/NT–Charging unit with power supply that charges either 10
BA151 rechargeable batteries or 10 RI250 infrared receivers
L151-10NT
74.000"
(1879.60 mm)
13.000"
(330.20 mm)
2 Pin Texas Connector
NT92–120 Power Supply
LED Indicator
Trickle Charge
(Green)
Button:
Press to begin
10 HR charge cycle
LED Indicator
Charge (Red)
Charging for
RI250, HDI302
Infrared Receivers
(Up to ten)
1.500"
(38.10 mm)
LED Indicators
Bright=Normal charge
Dim=Trickle charge
Charging for
BA151 Battery
(Up to ten)
5.450"
(138.43 mm)
ESZI1015-NT–Emitter panel for single, dual or multi channel use. Cover-
age: up to 4,000 sq. ft. in single channel mode. (3 lbs)
CBinder - Information Systems.indd 14 11/11/08 11:49:30 AM

Architects Specifications
SI1015-4000 Single
The infrared system shall be modular and provide coverage for up to 4,000 square feet in single channel mode.
The SI1015 modulator must utilize the higher sub-carrier frequencies of 2.3 and 2.8 MHz for single, two channel or stereo operation with an AF
frequency response of 50-15,000 Hz. It must be rack-mountable and have two monitoring diodes for the technician. It must accept line level
audio input via XLR connector. It must be easy to install using barrier strip with RF and DC outputs for connecting to emitters; and, alternatively,
BNC connectors for connecting the RF signal only. It must have AF level controls with LED’s indicating peak volumes. The modulator must be capable of
remotely powering one or two emitters.
The power supply NT1015-120 shall provide power for one SI1015 emitter and up to two SZI1015, and shall have an input voltage of 100-240 V
(1.3 A), an output voltage of approx. 29 V and an output current of 1.7 A.
The GA 1031-CC rack adapter is capable of mounting an individual SI 1015 modulator to a 19" rack.
The SZI1015 shall be wall or ceiling mountable via a mounting clamp with 5/8" external male thread, and the mounting plate shall have a diameter of
1 5/8".
The single-channel infrared receivers shall be stethoset design with a carrier frequency of 2.3 MHz. The AF frequency response must be 18-18,000 Hz.
The receivers shall contain a rechargeable Nickel Metal Hydride battery, which can easily be recharged with the L151-10/NT charging device (with power
supply) for up to ten rechargeable batteries.
The SZI1015 shall be an infrared emitter with a carrier frequency band that extends to 6 MHz RF input (50 mV to 3V) via BNC socket or barrier strip, RF
output via BNC socket or barrier strip. The unit shall offer excellent reliability due to 72 individual diodes. The unit shall offer an operating voltage of
25-30 V DC and weigh approx. 3 lbs. The unit shall be a Sennheiser SZI1015. Coverage: 4,000 sq. ft. in single channel mode.
Limited Product Warranty/Service
Sennheiser Electronic Corporation extends the following limited product warranty for Sennheiser products:
The warranty period for all covered Sennheiser products is two years from the date of purchase. Not covered by this warranty are accessories and other consumables;
for example, items of wear and tear, such as cables. During the warranty period, Sennheiser Electronic Corporation warrants that the Sennheiser equipment will be
free from defects in materials and workmanship used in making the product. Abnormal conditions, deliberate abuse and damage due to accidents, operator’s error, or
unauthorized service attempts are excluded from any warranty claims.
Under this warranty, Sennheiser Electronic Corporation will repair, or at its option, replace free of charge the covered defective Sennheiser product, provided it is returned
(postage paid, with proof of purchase from the original seller) to a Sennheiser Service Facility. Products should be returned in their original package, or otherwise suitably
protected to avoid shipping damage. Either product registration or a valid, dated proof of purchase is accepted to establish the warranty period. The Sennheiser Service
Department will be the sole authority to determine the validity of all warranty issues.
This Limited Product Warranty is Sennheiser Electronic Corporation’s only warranty, and the customer’s only remedy concerning Sennheiser products. All other rep-
resentations and warranties, express or implied, written or oral, including, but not limited to, any warranties of merchantability, fitness for a particular purpose, or
non-infringement, are expressly excluded. As a result, except as set forth in the previous paragraphs, the product is sold “as-is” and the customer is assuming the
entire risk as to the product’s suitability for his needs, its quality and its performance.
In no event will Sennheiser Electronic Corporation be liable for direct, indirect, special, incidental or consequential damages resulting from any defect in the product or
from its use, even if advised of the possibility of such damages.
Sennheiser Electronic Corporation • 1 Enterprise Drive • Old Lyme, CT 06371
SI1015-4000 Single System Package
CBinder - Information Systems.indd 15 11/11/08 11:49:30 AM