SEON Explorer TX8 User manual

DVR Firmware Version 2.0
Document Part Number 700-0158 R004
*700-0117*

About This Guide
The User Guide is intended for anyone who needs to operate, configure, or
troubleshoot the Explorer TX8 Mobile DVR System.
Related user guides include:
•Explorer TX8 Install and Setup Guide, 700-0157
•vMax View User Guide, 700-0137
Conventions Used
Abbreviations and Acronyms
Finding Information Online
You can find more information about Seon Design Inc. as well as its products and
services at www.seon.com.
CAUTION
Cautions identify conditions or practices that could result in damage to the unit or other
equipment.
Tip: These notes provide tips for optimum performance of the DVR system.
Important: These notes provide important information, which are not as serious as a Caution.
Acronym Definition Acronym Definition
CAN Controller area network LAN Local area network
DVR Digital video recorder OSD On-Screen Display
FPS Frames per second RA Return Authorization
GPS Global Positioning System TCM Transmission Control Module
HDD Hard disk drive TCP/IP Transmission Control Protocol/
Internet Protocol
H.264 H.264 video compression USB Universal Serial Bus
IR Infrared UTC Universal Time Coordinated

700-0158 R004 iii
Chapter 1 Introduction
1.1. Overview- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–1
1.2. TX8 DVR Product Features- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–2
1.2.1. Recording Capacity for DVR Hard Drive Storage - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–3
1.2.2. System Components - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–3
1.2.3. Front Panel Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–4
1.2.4. Back Panel Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–5
1.2.5. Trackball mouse - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–6
1.3. DVR Video Configuration Playback and Archiving - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–7
Chapter 2 DVR Operation
2.1. Remove and Replace the DVR Hard Drive - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–2
2.2. Search, Playback, and Archive Video- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–2
2.3. vMax View and HDD Dock - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3
2.4. On-Screen Display Access - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–4
2.4.1. Playback Menu Access - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–6
2.4.2. Using the Search Function - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–8
2.4.3. Using the Archive Function - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–11
2.4.4. Copy to USB - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–12
2.4.4.1. Archive Segmentation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–12
2.5. Using One-Touch Download - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–13
Chapter 3 vMax Web Operation
3.1. System Requirements- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–1
3.2. Accessing vMax Web - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–2
3.3. vMax Web User Interface - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–4
3.3.1. vMax Web Live Tab - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–5
3.3.2. vMax Web Configuration Tab - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–6
3.3.3. vMax Web Playback Tab - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–7
3.3.3.1. Search Video from Time Point or Event Marker - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–9
3.3.1. vMax Web Archive Tab - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–12
3.3.1.1. Archive Segmentation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–13
3.3.2. Viewing TX8 Video Archives - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–13
Chapter 4 DVR Firmware and Configuration Uploads
4.1. Firmware Updates - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4–2
4.2. Configuration Uploads - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4–3
4.2.1. USB Memory Device to DVR Configuration Upload - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4–3
4.2.2. Uploading Configuration Files to DVR via vMax Web - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4–7
Contents

Contents
iv 700-0158 R004
Chapter 5 Maintenance and Service
5.1. Returning Product for Service - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5–1
5.2. Troubleshooting the Explorer TX8 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5–2
Appendix A Specifications
A.3. Explorer TX8- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–1
A.3.1. Advanced Smart-Temp™ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–2
A.3.2. Explorer TX8 Functional Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–2
A.3.3. Explorer TX8 Front Cover, Cable Cover - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -A–2
Legal Notice
Seon Design® Inc. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - L–1
Contact Information - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - L–1
Seon Design Inc.® Product Warranty
Advance Replacements - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -W–1
Disclaimer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -W–2

Introduction
700-0158 R004 1–1
CHAPTER 1
Introduction
This chapter describes the product features and components of the Explorer TX8
Mobile DVR System. This chapter contains the following sections:
Overview, on page 1–1
TX8 DVR Product Features, on page 1–2
Recording Capacity for DVR Hard Drive Storage, on page 1–3
System Components, on page 1–3
Front Panel Features, on page 1–4
Back Panel Features, on page 1–5
Trackball mouse, on page 1–6
DVR Video Configuration Playback and Archiving, on page 1–7
1.1. Overview
This section introduces the product features of the Explorer TX8 Plus Mobile Digital
Video Recording (DVR) System.
The Explorer TX8 DVR integrates with the optional Smart-Reach Mobile wireless
technology and works with optional vMax Commander and vMax View video
management software for on-board video data management.

Introduction
1–2 700-0158 R004
1.2. TX8 DVR Product Features
The Explorer TX8 has the following product features:
• supports up to 8 video channels and 8 audio channels
• records up to 15 frames per second (FPS) at 720 × 480 D1 resolution on all video
channels simultaneously
• offers H.264 video compression for enhanced compression and quality
• has removable dual hard disk DVR drives
• stores up to 2.0 TeraBytes (TB)
• offers dual stream recording; high-resolution stream for playback on a PC, and a
lower resolution stream for viewing over a cellular phone network
• monitors DVR and hard drive status and notifies the administrator of any issues,
ensuring all onboard events are captured, using the vMax Commander video
management software Health Check feature
• uses Global Positioning System (GPS) technology for Geo-fencing, to designate a
geographic boundary for the vehicle and provides an alert if the vehicle leaves the
area
• uses G Sensor technology to provide driver behavior and accident impact velocity
data
• keyed access to front cover and secure cable cover with slotted cable entries to
restrict access to authorized personnel, see Figure 1-1
• configure, playback, and archive video from the DVR locally with trackball
mouse, portable video monitor, and DVR On Screen Display (OSD) and USB
memory device
• configure, playback, and archive video from the DVR remotely with vMax Web
via Wi-fi network or Ethernet connection
• interfaces with network using RJ-45 connections on the front and back panels, see
Figure 1-2 and Figure 1-3
Figure 1-1 TX8 DVR with Security Front Cover and Secure Cable Cover

Introduction
700-0158 R004 1–3
1.2.1. Recording Capacity for DVR Hard Drive Storage
The Explorer TX8 uses H.264 video compression to maximize the recording time on
the DVR hard drive. The amount of recorded video varies, depending on the FPS,
resolution (horizontal x vertical pixel count), number of cameras being recorded, and
picture quality settings. Lower picture quality results in higher compression and a
lower memory requirement. Higher picture quality results in lower compression and a
higher memory requirement.
Table 1-1 shows the estimated recording time in hours for 1 TB (two 500 GB DVR
hard drives).
1.2.2. System Components
The typical Explorer TX8 system consists of the following components (see DVR
Video Configuration Playback and Archiving, on page 1–7):
• Explorer TX8 DVR
• Cameras and camera cable, one connector per camera
• DVR hard drive
• Alarm button and cable
• Wiring harnesses
- power input harness with in-line fuses for constant and switched power lines
- adapter harness
- speed harness
• Trackball mouse and portable video monitor, optional
• GPS receiver, optional
• Diagnostic Button, optional
• RGY Illuminator, optional
• Smart-Reach Lite, optional
• HDD dock, optional
Important: The average image size is dependent on the scene content, lighting conditions, and amount
of movement recorded. External facing cameras will consume disk space more rapidly. Estimated
recording times are based on simulated test conditions. Actual recording times will vary greatly.
Table 1-1 Estimated Recording Time for 1 TB DVR Hard Drive, 8 Cameras
FPS
Picture Quality (3)
360×240 resolution 720×240 resolution 720×480 resolution
15 880 hours 473 hours 247 hours
10 1168 hours 686 hours 363 hours
5 2192 hours 1288 hours 694 hours

Introduction
1–4 700-0158 R004
1.2.3. Front Panel Features
Figure 1-2 shows the front panel features followed by a short description. For a full
description of the features, see DVR Operation, on page 2–1.
Figure 1-2 Front Panel
Item Feature Feature
1 DVR hard drive
lock
Requires the DVR Hard Drive key to unlock and remove the DVR.
See Remove and Replace the DVR Hard Drive, on page 2–2 for hard drive removal details.
2 DVR hard drive Playback the hard drive content in vMax View using the HDD Dock connected to a PC.
See vMax View and HDD Dock, on page 2–3 for hard drive playback details.
3 LAN (Gigabit) Ethernet port with RJ-45 connector for connecting to LAN. Connect to a laptop, Smart-Reach
Lite wireless equipment, or other equipment.
4USB1, USB2
ports (USB 2.0)
Supports USB mouse and memory devices for copying video and audio information, exporting
video clips, updating DVR firmware, importing/exporting DVR configurations.
5 LED displays • LAN activity, on when there is network activity on the LAN connection
• HDD activity, on when the DVR is accessing the hard drive
• PWR, on when the DVR is on
• TEMP, flashes fast when DVR cannot power up due to temperature limitations
• VOLTAGE, flashes slow when DVR cannot power up due to voltage limitations
6 AUDIO OUT RCA jack, for listening to live or recorded audio from the camera microphones.
7 VIDEO OUT RCA jack for DVR configuration, troubleshooting, video playback, live viewing with portable
monitor and mouse.
8 ONE TOUCH Download button, see Using One-Touch Download, on page 2–13.
9STOP/TEMP
PWR button
• STOP: press stop button to stop DVR playing or recording
• TEMP PWR: press to power on DVR temporarily when held for 5 seconds
• TEMP PWR: press to power down the DVR when held for more than 5 seconds when DVR
is in temporary power mode, or in shut down sequence
12 3
456798

Introduction
700-0158 R004 1–5
1.2.4. Back Panel Features
Figure 1-3 shows the back panel features followed by a short a description.
Figure 1-3 Back Panel Features
Item Feature Description
1 ALARM INPUT Alarm input connector for the alarm button.
2 CONTROL Control connector for controlling the Smart-Reach Mobile wireless bridge equipment.
3 1 to 8 Eight camera input connectors.
4 POWER OUTPUT Auxiliary power connector. Turns off after recording as configured in delay settings.
5 Fan Intake fan with filter and removable cover. See Maintenance and Service, on page 5–1.
6 ETHERNET Ethernet port with RJ-45 connector for connecting to LAN. Ethernet is used to connect
either to a PC or laptop or directly to the Smart-Reach Lite wireless bridge or other
equipment.
7 VIDEO OUTPUT Configurable video output for viewing video, BNC connector
8 SIGNALS Adapter harness connector for speed, diagnostic, and signal inputs.
9 GPS GPS connector.
10 Do not use For Seon use only.
11 POWER Power input connector for connecting the power harness.
ALARM
INPUT
POWER
OUTPUT
POWER
GPSSIGNALS
ETHERNET
CONTROL
VIDEO
OUTPUT
1 2 3 4 5
11
9876 10

Introduction
1–6 700-0158 R004
1.2.5. Trackball mouse
Many other USB mice will also work with the DVR.
Figure 1-4 Trackball Mouse Pointing Device
Table 1-2 Trackball Mouse Features
To do this… Item
Select the highlighted menu option by pressing the middle button. 1
Select the highlighted menu option by pressing the left button with your thumb. 2
• Delete a character entered into a field or go back to a previous items by pressing the button
on the right.
• Press this button to enter the configuration menu.
3
Move the cursor around the screen by rotating the blue button. 4
1
2
3
4

Introduction
700-0158 R004 1–7
1.3. DVR Video Configuration Playback and Archiving
Here is an introductory overview of the configuration, playback, and archiving
methods available on the TX8.
The TX8 DVR content can be accessed and archived in four ways:
• locally via OSD and portable video monitor. See DVR Operation, on page 2–1.
• Locally via One Touch button and USB memory device. See Using One-
Touch Download, on page 2–13.
• remotely via vMax Web browser interface and Ethernet/wireless connection.
See vMax Web Operation, on page 3–1.
• via vMax View video management software and DVR hard drive interface.
See vMax View and HDD Dock, on page 2–3. See also:
•vMax Commander Software User Guide, 700-0120
or
• vMax View User Guide, 700-0137
The following table shows which methods support video configuration, playback, and
archiving.
To do this… Use...
On-screen display
with monitor and
trackball mouse
vMax Web remote
access with
Internet Explorer
DVR HDD Dock
and vMax View
software
Configure the DVR menu settings. See TX8 Installation
and Configuration Guide, 700-0157.

Playback and view recorded video with single channel
view or multiple views.
 
Search for video from a Segment, an Events list, or by
time and date.
 
Archive video to .avr file format.  
Archive low resolution (Record2) video stream 
Archiving options — each individual channel can be
archived as a .avi file and individual images saved as
.bmp or .jpg files


Introduction
1–8 700-0158 R004

DVR Operation
700-0158 R004 2–1
CHAPTER 2
DVR Operation
This chapter provides information and procedures for operating the Explorer TX8. This
chapter contains the following sections:
Remove and Replace the DVR Hard Drive, on page 2–2
Search, Playback, and Archive Video, on page 2–2
vMax View and HDD Dock, on page 2–3
On-Screen Display Access, on page 2–4
Playback Menu Access, on page 2–6
Using the Search Function, on page 2–8
Using the Archive Function, on page 2–11
Copy to USB, on page 2–12
Using One-Touch Download, on page 2–13

DVR Operation
2–2 700-0158 R004
2.1. Remove and Replace the DVR Hard Drive
The DVR has a removable hard drive that is contained in a drive tray. A hard drive
lock secures the cartridge during operation. Use the hard drive key to lock and unlock
the hard drive.
To remove the hard drive:
1. Insert the hard drive key.
2. Turn the hard drive key counter clockwise by ¼ turn until the hard drive lock is in
the unlocked position.
3. After the red HDD LED is off, gently pull out the hard drive.
To replace the hard drive:
1. Slide in a hard drive until the cartridge seats inside the front panel.
2. Insert the hard drive key, turn clockwise by ¼ turn until the hard drive lock is in
the locked position.
2.2. Search, Playback, and Archive Video
To search, playback, and archive recorded video, use one of these methods:
vMax View and DVR Hard Drive Dock
Remove the DVR hard drive from the DVR, and use the TX8 HDD Dock and vMax
View software. See vMax View and HDD Dock, on page 2–3.
On Screen Display Menus
For local video access, connect a portable video monitor to the TX8 DVR Video Out.
Use the trackball mouse to navigate the OSD menus. See On-Screen Display Access,
on page 2–4.
vMax Web Menus
For local or remote video access, use a laptop and the vMax Web browser user
interface with Ethernet or Wi-fi connectivity. See Accessing vMax Web, on page 3–2
for access instructions.
One Touch Button and USB memory Device
For quick download of flagged video, use the One Touch Button and a USB memory
device. See Using One-Touch Download, on page 2–13 for instructions.
CAUTION: Data Loss Risk
Do not remove the DVR hard drive until the red HDD activity indicator is off.
Failure to do so may result in lost data. While the DVR hard drive is hot swappable
(the drive can be removed when the DVR is powered up), do not remove the DVR
hard drive while the DVR is recording, as some video segments may not be recorded.

DVR Operation
700-0158 R004 2–3
2.3. vMax View and HDD Dock
The HDD Dock is provided with vMax View software to accommodate the TX8 drive.
The HDD Dock uses AC power and a USB3 connector to the PC.
To access video from the drive using vMax View:
1. Connect the AC adapter to the HDD Dock socket.
2. Connect the AC adapter to an AC power outlet.
3. Connect the USB cable to a PC socket.
4. Power on the HDD Dock using the button between the USB and AC cable
connectors.
5. Remove the drive from the DVR.
6. Insert the TX8 DVR hard drive into the HDD Dock as shown.
On the PC, launch vMax View and search the drive for the required video to
archive. See vMax View User Guide 700-0137 for detailed procedures.
Figure 2-1 DVR HDD to USB Interface with Hard Drive

DVR Operation
2–4 700-0158 R004
2.4. On-Screen Display Access
Use the On-Screen Display mode to locally access the DVR hard drive content and
menus.
To use the on-screen display (OSD) with trackball mouse and monitor:
1. Connect a portable video monitor to the VIDEO OUT RCA jack on the TX8 front
panel. Plug the USB trackball or mouse in a USB socket on the front of the DVR.
When the DVR starts up, the Seon Explorer TX8 splash screen appears briefly
before the DVR enters live view.
During recording and live viewing, the screen information is dynamic and can
include the items shown in Figure 2-4 and described in Table 2-1. The screen
items can be configured in the main menu.
Figure 2-2 Mouse and Monitor Connected to DVR
Figure 2-3 TX8 Splash Screen
Figure 2-4 On-Screen Display during Live Viewing and Recording
Portable
Video Monitor
TX8 DVR
USB Mouse

DVR Operation
700-0158 R004 2–5
2. Use the trackball mouse (right-click) to access the DVR’s configuration,
playback, and archiving menu settings as required.
3. Proceed to the Configuration or Operation and Playback chapters for details on
available setting options.
Table 2-1 On-Screen Display Information
Feature Description
Camera 1 to Camera 8 Camera titles, maximum 8 characters each.
Main_Title Main title of the DVR, maximum 32 characters.
HD Size Formatted size of the DVR hard drive, in gigabytes (GB).
HD Used Percentage of recorded video on the DVR hard drive. At 100%, the message displayed depends on the
Repeat Record settings in the Recording Settings menu.
• When Repeat Record is set to On, the HD Used message reads “N/A Repeating”. N/A means that
information on how much of the hard drive space is used is not available because the hard drive is
full. Repeating means the DVR continues recording, overwriting the oldest recorded data.
• When Repeat Record is set to Off, the HD Used message reads “100%”. The DVR stops recording.
Version DVR firmware version. To update, see Firmware Updates, on page 4–2.
Status DVR operation status:
• LIVE (live mode not recording)
• PLAYBACK (the DVR is playing locally, displays RECORD, ALARM, or TIMER)
• RECORD (normal recording)
• ALARM (alarm recording)
• TIMER (timer recording)
• V. LOSS (video loss or camera signal loss)
Camera Off Indicates how long the cameras are recording after the DVR powers down. Configured as Record
Delay-Off time from 0 seconds to 30 minutes.
Speed Display Vehicle speed in MPH or KPH.
Voltage System voltage from 8 to 32 VDC.
Temperature DVR temperature in degrees Fahrenheit or Celsius.
GPS If the GPS receiver is installed, the vehicle’s latitude and longitude is displayed.
Time and Date Current/recorded time and date.
AC (Alarm count) Count of alarm(S) triggered. Resets to 0 when the DVR is restarted.
IG (Ignition) Appears when vehicle ignition is on.

DVR Operation
2–6 700-0158 R004
2.4.1. Playback Menu Access
Use the Playback menu to search, playback, and archive video directly from the DVR
hard drive.
To access the playback menu from the OSD:
1. In the OSD view, right-click the live view to access the Main Menu and click
Playback.
2. Click on the Show/Hide tool bar icon in the center of the window.
The playback tool bar appears.
Figure 2-5 Main Menu
Figure 2-6 Playback Tool Bar Window

DVR Operation
700-0158 R004 2–7
Table 2-2 Playback Tool Bar Items
Tool Bar Icon Description
Start of clip/End of clip Click to set the start of clip and the end of clip
points for archiving. See Using the Archive
Function, on page 2–11.
Search Click to search by Date, Time, Alarm, Signals, or
System Event.
Archive Click to display the Archive window to save a video
clip to USB memory device.
Fast Rewind Click to reverse during playback. With playback
paused, each click reverses the video by one frame.
Play/Pause Click to start playback.
Click again to pause playback.
Fast Forward Click to fast forward during playback. With
playback paused, each click advances the video by
one frame.
Individual camera/Quad view Click to display Camera 1 - 8 or quad view.
Audio Click to cycle through Audio 1 - 8.
Metadata Text overlay Click to turn on text overlay: temperature, system
voltage, GPS data (if recorded), speed, date, and
time.
Show/Hide Playback tool bar Click to show or hide the playback tool bar.
Exit Click to exit to on-screen display.
1

DVR Operation
2–8 700-0158 R004
2.4.2. Using the Search Function
The TX8 includes a powerful search function that lets you quickly find recorded
information by Date and Time, Alarm, Signals, or System Events.
To view the Search menu:
1. From the playback tool bar, click on the Search icon.
The Search menu appears as shown in Figure 2-7. The items appearing in the
dialog box will depend on the item selected in Search Only box.
Figure 2-7 Search Menu
Table 2-3 Search Configuration Items
Menu Item Description Value [Default]
Start Date Set the start date for the search.
Time Set the start time for the search.
Search Only Select the desired search type. • [Time]
•Alarm •Alm1 - Alm4, All
• Signals • Signal 1 - Signal 10, All
• System
Event
•GPS
• Ignition
• Recording
•Timers
•Video Loss
• G Sensor
•Speed
•All
Search Press Enter to Start Search.