Serene Classic User manual

Serene ‘Classic’
Rails
Heated Ladder Towel Rails - Curved
User Manual
PRN2169Rev.4.0Aug.2013

C l a s s i c S e r i e s
2 SERENE Heated Ladder Towel Rails
Contents
1 Safety Information ........................ 3
2 Installation ..................................4
Wiring .............................................. 4
Distances ......................................... 4
To Install the Towel Rail ..................... 4
3 Operation .................................... 7
4 Specifications ...............................7
Dimensions ........................................... 7
Electrical ............................................. 7
Construction .......................................... 7
5 Maintenance ............................... 8
6 Contact Addresses ..................... 8
Copyright © 2013 Serene Industries Limited.
Serene Industries Limited reserve the right to alter specifications without notice.

C l a s s i c S e r i e s
3 SERENE Heated Ladder Towel Rails
1 Safety Information
When using any electrical appliance, safety precautions should always
be observed. Read these instructions carefully before installation and
retain for future reference.
This appliance is intended to dry towels and therefore is hot to the
touch. When used by or near young children or infirm persons,
close supervision is necessary. Young children should be
supervised to ensure that they do not play with the appliance.
Any rise in ambient temperature is directly reflected in the
appliance and as a result of this the appliance willfeel hotter to the
touch during warmer periods. The insulation effect of towels will
also cause the operating temperature to increase.
Use this appliance only on the voltage specified on the rating label.
Regulations require that electrical work be carried out only by
authorised persons. For your own safety, and that of others,
ensure this is done.
To avoid a hazard for young children, this appliance MUST be
installed so that the bottom rail is at least 600mm above the floor.
To avoid a hazard this heated towel rail MUST NOT be used to
carrytowelsor any other articlesthat have been in contact with oil,
petroleum based products or dry cleaning fluids.
Do NOT use this appliance other than for its intended use.
Do NOT immerse in any liquid.
Do NOT allow the power supplycord to come into contact with
heated surfaces during operation.
Caution:
If this appliance is supplied from a cord extension set or an electrical
portable outlet device, the cord extension set or electrical portable
device must be positioned so that it is not subject to splashing or
ingress of moisture.

C l a s s i c S e r i e s
4 SERENE Heated Ladder Towel Rails
2 Installation
This appliance MUST be installed in accordance with the relevant
wiring rules and regulations which cover installation of appliances and
accessories in damp situations such as bathrooms, showers, laundries
and other areas with fixed water containers (in Australia and New
Zealand - AS/NZS 3000: 2000 Wiring Rules).
Wiring
The Heated Ladder Towel Rail is supplied with a 900mm supply cord
and plug. This Class II appliance does NOT require Earthing. Where
protected by an RCD, the Heated Towel Rail can be plugged directly
into a socket outlet, otherwise permanent connection to the supply via
a permanent connection unit is required. On directly wired models, a
suitable disconnection device (acting in all supplies) MUST be
incorporated in the fixed supply wiring.
Distances
In order to avoid a hazard for young children, this appliance MUST be
installed so that the bottom rail is at least 600mm above the floor.
Theside frames of the Towel Railshould be mounted vertically, with the
heated rails horizontal and the supply cord at the bottom.
To Install the Towel Rail
1. Remove allthe packingmaterialfrom around the towel rail and
retrieve the fixing screws and adhesive dots from inside the
plastic bag taped to the power cord.
2. Establish a suitable position on the wall for attaching the towel
rail, with at least two of the leg mounting brackets aligned with
wall studs or dwangs.

C l a s s i c S e r i e s
5 SERENE Heated Ladder Towel Rails
3.
Remove all four of the mounting
brackets from the towel rail frame by
undoing the small hexagon socket
screw under each leg. Be careful not to
lose the screws.
4.
Mark the location of ONE of the
mounting brackets on the wall.
5.
Drill a hole centrally at the marked
location and fix the mounting bracket
to the wall, either using a wall fixing
screw (supplied) or a suitable wall
fixing plug.
6.
Attach one of the adhesive dots
(supplied) to the back of each of the
remaining three mounting brackets
and remove the protective paper
backing.
7.
Insert the remaining three mounting
brackets into the frame mounting legs.
Ensure the rectangular fixing slot, in
each mounting bracket, faces
downwards so as to correctly align with
the fixing hole in each of the frame
legs.

C l a s s i c S e r i e s
6 SERENE Heated Ladder Towel Rails
8. Position the corresponding towel rail
frame leg onto the mounting bracket
already attached to the wall. If
necessary, use a level to align the
towel railin the desired position, before
pressing firmly against the frame to
adhere the remaining three mounting
brackets to the wall.
9. Pull the frame away, leaving the
mounting brackets attached to the wall.
10. Drill and attach the remaining three
mounting brackets to the wall using
either the three wall fixing screws
(supplied) or suitable wall fixing plugs.
11. Refit the towel rail frame over the
mounting brackets and lock in place
with the four small hexagon socket
screws.
12. Either connect the supply cord to a
socket outlet or, if installed in a
bathroom, have an authorised person
connect the supply cord to a switched
permanent connection unit.

C l a s s i c S e r i e s
7 SERENE Heated Ladder Towel Rails
3 Operation
The Heated Ladder Towel Rail will take approximately 45 minutes to
reach normal operating temperature and, if need be, can be left running
continuously. The Heated Ladder Towel Rail costs approximately the
same to run as a 100 Watt light bulb.
4 Spe c i f i ca ti o n s
Dimensions
Model
SLTR5SS
SLTR7SS
SLTR9SS
SLTR11SS
Height:
560mm
805mm
1040mm
1280mm
Width:
630mm
630mm
630mm
630mm
Depth:
125mm
125mm
125mm
125mm
Weight:
2.0 kg
2.5 kg
3.1 kg
3.8 kg
Electrical
Supply: 230-240 Volts a.c. 50 Hz
Wattage: 45-50 W 65-70 W 87-95 W 105-115 W
Insulation Class: Class II - Double Insulated
Wiring: 900mm 2-core supply cord and plug. The plug may be
removed for connection to permanent wiring.
Controls: No controls provided. Designed for continuous
operation. The LEDindicates when the towel rail is
operating.
Const r uc ti on
Ingress Protection Rating: IP34 –Splash proof
Finish: Polished stainless steel frame, with chrome plated
fittings, and white supply cord and plug.
Table 1: Specifications

C l a s s i c S e r i e s
8 SERENE Heated Ladder Towel Rails
5 Maintenance
The Heated Ladder Towel Rail is best wiped down from time to time
with a damp cloth. Do NOT use any abrasive or corrosive cleaners.
The supply cord on this product cannot be replaced without damaging
the appliance. If the supply cord becomes damaged in any way, the
appliance should be scrapped. If the appliance is under warranty,
contact Serene Industries Limited.