Serene S6068 Sorroco User manual

S6068 Sorroco
Infrared Outdoor Heater
Instructions &
Operation Manual

Safety Information:
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
When using any electrical appliance, safety precautions should always
be observed. Read these instructions carefully, and retain for future
reference.
When used by, or near, young children or infirm persons, supervision isnecessary.
Young children should be supervised to ensure that they do not play with the
appliance.
Use this appliance only with the voltage specified on rating label.
Do NOT use this appliance other than for its intended use.
Do NOT touch hot surfaces or moving parts.
Do NOT cover the grilles or place any object or material up against
the unit, as this may block entry or exhaust of air.
Do NOT probe any opening.
To ensure trouble free performance it is recommended that on a regular basis the unit be
isolated from the power supply and a vacuum cleaner used to remove dust from the inlet
and outlet grilles.
Caution:
When the heater is operated ensure the heater is not obstructed in
any way. Ensure the heater can operate safely, should the heater switch on when the
ambient temperature drops, or a timer activates the heater.
Do NOT allow the supply cord to come into contact with heated
surfaces during operation.
Regulations require that electrical work be carried out by authorised
persons. For your own safety and that of others, ensure this is done.
If the supply cord becomes damaged, it must be replaced by a
qualified person, in order to avoid a hazard.

•
•6•7•7
For additional protection the installation of a residual current device
(RCD) is recommended. ( Refer to local electrical regulations)
Remove all packaging e. material ( and check the appliance, supply cord and the plug
for signs of damage
Pay attention to the mounting place and all mounting material. Ensure they are suitable
and stable enough for mounting and holding the appliance on your chosen surface.
Before mounting, the minimum safe mounting distances and tilt angles shown in the
figures must be strictly followed.
45mm 45mm
45mm
0.2m
0.5m
1.8mm
Installation
The distance between the bottom edge of the appliance and the floor must be at least
2.5 M.
There must be a distance of at least 0.5 M between the appliance and the ceilings,
roofs or other covers. If the covers consist of flammable material, such as wooden
ceilings, wooden roofs etc., the distance at least 1 M must always be maintained.
There must be a distance of at least 1.5 M at each side between the appliance and
walls or the like. See figure 3.
The max. degree to horizontal is 60°and the min. degree is 40°.See figure 4.
The infrared heater could also be swung from left to right. The max. swing degree is
25°.
Pay attention that, the installation of the appliance must not add excessive wind load.
Fix the wall mounting bracket on the wall first. Ensure that the place to be installed is
secure and firm.
Assemble the appliance onto the mounting bracket. Adjust the desired angle of
radiation and screw in all screws.
Check regularly the screws’ connection. Mechanical bearing pressure and oscillation
due to wind or rain could lead to loosend screws.
Connect the power source. Observe whether during the first 10-15 minutes the
appliance is functioning.

Figure 1: Mounting bracket (wall
bracket) and anchor
dowels
provided
Figure 2: Connection from wall bracket to
the infrared heater with the max. Side
angle.
Figure
3: Min. distance to
floor,
ce
iling and wall
Figure
4: Minimal and maximal tilt angle
Specification
Model
S2068
Voltage (V)
220
-240～
Power consumption (W)
1200
Dimensions W x H x D (mm)
400X190X306mm
Weight (kg)
3.7
IP protection
IP
54
Specifications
Installation

Cleaning and Maintenance
This appliance is constructed of a robust and maintenance-free aluminum casing with
a cover of toughened glass. There are no user serviceable parts inside.
Before cleaning remove the plug from the power outlet (if fitted) and wait until the
appliance is sufficiently cool.
Wipe the appliance only with clean and lint-free cloth or a soft brush.
Caution! Before the next use the unit must be dry.
Never use abrasive cleaners, scrubbing brushes and chemical cleaners for cleaning!
Never use flammable cleaners such as benzine or spirits.
To protect against electrical shock do not immerse cord, plug, or any part of the
appliance in water or other liquid.
For heating element replacement please contact Serene Industries Limited or a
properly qualified service person.
Recomended Disposal
In accordance with the European Directive 2011/65/EU (not yet mandated in AU and
NZ) concerning used electrical and electronic appliances please return any electrical
equipment that you will no longer use to suitable waste collection points provided for
their disposal.
This symbol indicates that the appliance should not be treated as normal domestic
trash.

Contacts:
HONG KONG
Head Office - Serene Industries Limited
t: [phone]
f: [phone]
e: [e-mail]
w: www.serene-ind.com
Suite 1010, 15F, Block A, Alexander Industrial Building, 62 King Lam
Street,
Cheung Sha Wan, Kowloon Hong Kong SAR
NEW ZEALAND
t: (+) 64 (3) 344 5550
f: 0800 437 264- Freefax
e: nz[email protected]
w: www.serene-ind.com
PO BOX 33501, Barrington, Christchurch 8024
AUSTRALIA
t: + 61 (3) 8354 4133
f: + 61 (3) 9699 6422
fp: [phone]- Freephone
e: [e-mail]
w: www.serene-australia.com
Suite 201 / 175B Stephen Street, Yarraville
Melbourne VIC 3013