Serene S2068 User manual

Serene S2068
1 Bathroom Fan Heater
Serene S2068
Serene Bathroom Fan Heater
Operating
Instructions

Serene S2068
2 Bathroom Fan Heater
Introduction
Designed for easy installation, your Serene S2066 - S2068 Metal Bathroom Fan Heater includes a
clip- on wall mount bracket for faster and easier installation. This model S2068 bathroom fan heater
has been designed to cover the footprint of previously available SERENE and SKOPE models
Safety Information
• When using any electrical appliance, safety precautions should always be observed. Read these
instructions carefully and retain for future reference. For service, contact your nearest
authorised service agent.
• When used by, or near young children or infirm persons, close supervision is necessary.
Young children should be supervised to ensure that they do not play with the appliance.
• Do NOT use this appliance other than for its intended use.
• Use this appliance with the voltage specified on the rating label.
• Be very careful not to touch hot surfaces or moving parts.
• Do NOT cover the grilles or place any object or material up against the unit as this may block
the entry or exhaust of airflow.
• Do NOT probe any opening to remove fluff. Toensure trouble-free performance, it is
recommendedthat the unit be isolated from the power supply and a vacuum cleaner used to
remove dust and fluff from the inlet and outlet grilles on a regular basis.
• Regulations require that electrical work be carried out by authorisedpersons. Foryour
own safety and that of others, ensure this is done.
• Do NOT allow the supply cord to come into contact with heated surfaces during operation.
• If the supply cord becomes damaged, it must be replaced by a qualified person in order to
avoid a hazard.
Installation
This appliance MUST be installed in accordancewith relevant
wiring rulesandregulationswhichcoverinstallationofappliances
andaccessories indampsituations, such asbathrooms,showers,
laundries andother areas with fixed water containers (in
Australia and New Zealand - AS/NZS3000:2000 Wiring Rules).
Distances
Theheatermustbemountedaminimumdistanceof:
• 1800mm from floorlevel
• 200mmmbelowtheceiling
• 250mmfromadjacentwalls
Important: Theheatermust NOT belocatedimmediatelybelowa socket outletor within reach of a bath
or shower.

Serene S2068
3 Bathroom Fan Heater
To attach the heater to the wall:
1. Remove the wall mounting base from the heater by using a screwdriver (large flat blade) to release
both of theside clips from inside the base.
2. Secure the mounting base to the wall using the four fixing screw holes provided. The base supplied
with the heater must be used when attaching the heater to the wall.
3. Put the heater onto the mounting base and snap it into position.
4. Connect the flexible cord to the mains power supply. A suitable disconnect device is required to be
incorporated in the fixed supply wiring.
Operation
The operation of the heater is controlled by use of the pull-cord switch. Pull the pull-cord to switch the
heater on. Pull the pull-cord again to switch the heater off. The blue LED indicator lights when the heater
is operating.
The heat output is regulated by an internal step-down thermostat, which will reduce the output from
2200-2400 Watts to 1100-1200 Watts, when a comfortable room temperature is reached.
Care
The heater requires regular cleaning to ensure trouble free operation.
• Isolate the heater from the mains power supply.
• Use a damp cloth to clean the exterior of the heater. Do not use any abrasive cleaners.
• The S2068 is fitted with our “Airslip” metal fan blade that alleviates any dust build up inside the
heater.
• Use a vacuum cleaner to remove dust and fluff visible on the heater inlet and outlet grilles.
• Ensure the heater is dry before turning heater back on.

Serene S2068
4 Bathroom Fan Heater
Specifications: Serene S2066 - S2068
Electrical
Supply 230-240 volts A.C. 50 Hz
Wattage 2200-2400W, thermostatically reduced to 1100-1200W
Wiring Permanent connection. Double insulated, no earth required.
Ingress Protection Rating IP23
Dimensions
Height 210mm
Width 300mm
Depth 110mm (includes mounting base)
Weight 2.35kg
Serene Industries Limited reserves the right to alter specifications without notice.
Contact:
HONG KONG
Head Office - Serene Industries Limited
t: [phone]
f: [phone]
e: [e-mail]
w: www.serene-ind.com
Suite 1010, 10F, Block A, Alexander Industrial Building, 62 King Lam Street,
Cheung Sha Wan, Kowloon Hong Kong SAR
NEW ZEALAND
t: (+) 64 (3) 344 5550
f: 0800 437 264- Freefax
e: [e-mail]
w: www.serene-ind.com
PO BOX 33501, Barrington, Christchurch 8024
AUSTRALIA
e: [e-mail]
w: www.serene-ind.com
UNITED KINGDOM
t: [phone]
e: [e-mail]
w: www.serene-ind.com
Rowhead House, Far Common Road
Mirfield, West Yorkshire WF140DQ