Serene S2044 ROMA User manual

InstallationandOperatingManual
Serene S2044 ROMA
Space Heater
PRN10412Rev.2.1 August2013

2 Serene S2044 ROMA Space Heater
Safety Information
When using any electrical appliance, safety precautions should always
be observed. Read these instructions carefully, and retain for future
reference.
 When used by, or near, young children or infirm persons, close
supervisionisnecessary. Youngchildrenshouldbe supervisedto
ensure that they do not play with the appliance.
 Do NOT use this appliance other than for its intended use.
 Do NOT cover the heater or place any object or material up
against the unit, as this may block entry or exhaust airflow, and
cause the heater to overheat.
 Do NOT probe any opening to remove fluff.
 Do NOT allow thesupply cordto come into contact with heated
surfaces during operation.
 Do NOT usethis heater close to showers, baths or swimming
pools.
 Do NOT usethe heater in rooms with explosivegas or while using
flammable solvents, such as varnish or glues.
 When leaving the house for extended periods ensure the heater
thermostat is set on ‘Freeze Guard’ or the wall switch is turned off.
 Use this appliance with the voltage specified on the rating label.
 Be very careful not to touch hot surfaces or moving parts.
 If the supply cord becomes damaged, it must be replaced by a ly
qualified person, in order to avoid a hazard.
 Regulations require that electrical work be carried out by
authorised persons. For your own safety and that of others, ensure
this is done.

3 Serene S2044 ROMA Space Heater
Positioning
This heater is water resistant to IP24. It can therefore be used in
bathrooms or other areas subject to humidity, The heater must be
installed so that switches and other controlscannot be touched by a
person in the bath or shower.
The heater must be mounted on the wall, with a minimum height of
300mm above the floor or any other objects heated below it, and a
minimum distance of 400mm below the ceiling and from adjacent walls.
The heater must not be located immediately below a socket outlet.
Ensure that the heater is not mounted in a situation where the heated
air is directed over an open door, curtains, or any towel rail, creating a
fire risk. Leave at least 1 metre of space in front of the heater to allow
correct air delivery.
The heater must be mounted a minimum distance of:
 300mm above floor level or any other objects heated below it
 400mm below the ceiling and from adjacent walls
Ceiling
Floor
Wall
400mm
Min.
400mm
Min.
300mm
Min.
400mm
Min.
Wall

4 Serene S2044 ROMA Space Heater
Thermostat
The heat output is regulated by a built-in thermostat. The thermostat
maintains the required ambient temperature by automatically turning
the heater on and off.
Starting from the ‘Freeze Guard’ position, turn the thermostat knob
clockwise until you hear a ‘click’. The heater will then start heating and
the LED indicator will light up. The more the thermostat knob is turned
clockwise, the higher the ambient temperature will be.
If the ambient temperature is close to 30°C or more, the heater may not
turn on even if the thermostat is set on maximum. Alternatively, if the
ambient temperature is below 5°C, the heater may operate
continuously even if the thermostat is set on minimum.
To set the thermostat:
1. Turnthethermostatknob
clockwise to maximum
and wait until a
comfortable ambient
temperature is reached.
2. Turnthethermostatknob
anti-clockwise until you
hear a ‘click’ and the
heater turns off.
3. Fineadjustmentscan
then be made.
Freeze Guard
LED Indicator
Freeze Guard
Thermostat Knob
When the thermostat knob is turned fully anti-clockwise, pointing to the
‘Freeze Guard’ symbol, the heater will operate if the room
temperature falls below 5°C.
Note: This heater does not have an on/off switch. To turn the heater off
it must be turned off at the wall switch. At times when the Freeze Guard
function is not required, it is recommended that the heater is turned off
using the wall switch.

5 Serene S2044 ROMA Space Heater
Filter
This heater is fitted with an air
filter to protect the heating
elements from dust and dirt. The
filter is removable and can be
fitted from either the left or right
hand side of the heater. To keep
the heater operating efficiently,
remove and clean the filter once
every six months. Ensure the
filter is always fitted before
operating the heater.
Safety Cutout
This heater is fitted with a thermal safety cutout device. In the case of
over-heating, the safety cutout automatically switches off the heating
elements and fan motor. As a result, the heater stops working but the
LED indicator stays on.
Note : If the heater switches off, the LED indicator may also turn off
when the room temperature reaches the thermostat setting.
If the safety cutout is activated:
1. Turn the heater off at the wall switch and leave to cool for
approximately 30 minutes.
2. Check the air filter and clean if necessary. Ensure the filter is
fitted again before operating the heater.
3. Eliminate any other possible reason for overheating (such as
obstacles in front of the air inlet and outlet grille).
4. Turn the heater on and check operation. If the heater still fails to
operate, contact your nearest authorised service agent.
Care
The heater is best wiped down from time to time with a damp cloth. Do
not use any abrasive cleaners.
Air Filter

6 Serene S2044 ROMA Space Heater
Specifications
Dimensions
Height: 430mm
Width: 270mm
Depth: 135mm
Weight: 3.0 kg
Electrical
Wattage: 2000-2200 Watts
Supply: 230-240 Volts a.c. 50 Hz.
Wiring: Permanent connection. Double Insulated - no earth required.
Ingress Protection Rating: IP24
SERENE Industries Limited reserves the right to alter specifications without notice.
Contact Addresses
NEW ZEALAND
t:[phone]
f: 0800 437 264
e: [e-mail]
w: www.serene-ind.com
PO BOX 33501, Barrington, Christchurch
8024
AUSTRALIA
e: [e-mail]
w: www.serene-ind.com
HONG KONG
t: [phone]
f:[phone]
e: [e-mail]
w: www.serene-ind.com
1508, 15th Floor, 9 Wing Hong Street
Cheung Sha Wan, Kowloon
HONG KONG
IP24