Seville Classics SHE05813BZ User manual

Customer Service Informaon
Telephone: [phone]
Fax: [phone]
Hours: 8:30 AM – 4:30 PM (PST)
Email: [e-mail]
Homepage: www.SevilleClassics.com
Specicaons
Dimensions: 58" W (expandable up to 83") x 14" D x 72" H
Weight capacity per shelf: 100 lbs.
Weight capacity per rod (extended): 125 lbs.
Weight capacity per rod (unextended): 50 lbs.
FAQs
Q: Can I use it with only one expandable rod?
A: Yes! The towers can stand on their own without either rod aached.
Q: How many shelves do I need to install?
A: You only need to install shelves at the boom and very top of each tower.
Q: Can I install the shelves in any order?
A: Yes! Customize the unit to t your storage needs. Make sure there is a top
and boom shelf for stability.
Expandable Closet Organizer System
Model #: SHE05813BZ, SHE05814B
Thank you for choosing Seville Classics! We hope that you enjoy your
commercial-grade steel wire shelving! Please read through this guide for
parts list, assembly instrucons, frequently asked quesons and further
contact informaon.
112019

Parts List
B. Top poles (8)
(Plasc cap on end)
Please make sure you have all the parts on this list.
If you’re missing parts, contact us for replacements at
[phone] or send an email to [e-mail]
1
D. Shelves (8)
F. Rod bracket (4)
G. Expandable rods (2)
H. U-clips (4)
E. Top shelves (2)
A. Boom poles (8)
(Threaded end)
C. Slip sleeves (48)
I. Screws (4)
J. Feet (8)
K. Liners (8)
L. Nylon Straps (2)
M. Drywall screws (4)
N. Wood screws (4)
Required Tools
O. Wall anchor (4)
Phillips Screwdriver
Power drill
Wall Strap Installaon
STEP 1.
Loop the NYLON STRAPS (L)
around the side of top-shelf
nearest to the wall.
Use 1 per tower.
STEP 2.
Pull the NYLON STRAPS (L)
against the wall and mark
holes where you'd like to
install your ANCHORS (O) or
SCREWS (M, N).
TIP!
Use a stud nder to deter-
mine if you are installing into
drywall or wood.
FOR DRYWALL
Drill a hole in the wall at the
marked point roughly the
depth of the ANCHOR (O).
Screw the ANCHOR (O) into
hole unl ush.
Screw DRYWALL SCREW (M)
into ANCHOR (O) unl snug.
FOR WOOD STUDS
Drill a pilot hole into the wall
at the marked point.
Screw WOOD SCREWS (N)
into holes unl ush.
IMPORTANT
Installing wall straps is not necessary, but it is highly recommended.

STEP 7.
Clip U-CLIP (H) over BRACKETS (F).
Aach the small end of EXPANDA-
BLE ROD (G) to U-CLIP (H) with
SCREWS (I). Aach large end to
other tower.
STEP 8.
Insert LINERS (K) to shelves.
Pull towers out so that the closet
organizer ts your space.
Congratulaons!
Enjoy your new closet organizer.
TIP!
Adjust the depth of the
U-CLIPS (H) to oset the rods for
more hanging space.
2
Assembly Instrucons
STEP 1.
Screw LEVELING FEET (J) into base of
boom poles.
Snap SLIP SLEEVES (C) around the
grooves on BOTTOM POLES (A) for
your lowest shelf.
TIP! Perform each step for both
towers at the same me.
STEP 2.
Fit SHELF (D) over the top of the 4
poles and over SLIP SLEEVES (C).
Lightly tap shelves into place.
Repeat STEPS 1-2 for next shelves.

STEP 3.
Decide on the height for your
boom ROD BRACKET (F).
Fit SLIP SLEEVES (C) around two
poles on the same side.
Slide ROD BRACKET (F) over SLIP
SLEEVES (C).
STEP 4.
Screw in TOP POLES (B).
Repeat STEP 2-3 for next shelves.
IMPORTANT!
Test the height with clothes on
hangers to conrm you have
enough space when you install
the EXPANDABLE ROD (G).
STEP 5.
Decide on the height for your top
ROD BRACKET (F).
Fit SLIP SLEEVES (C) around two
poles on the same side.
Slide ROD BRACKET (F) over SLIP
SLEEVES (C).
STEP 6.
Snap SLIP SLEEVES (C) around the
grooves on TOP POLES (B) for
your top shelf.
Fit TOP SHELF (E) over SLIP
SLEEVES (C) and lightly tap into
place.
TIP! If tower is too high to place
nal shelf, lt the unit on it's side
for an easier installaon
IMPORTANT!
Test the height with clothes on
hangers to conrm you have
enough space when you install
the EXPANDABLE ROD (G).