SEW-Eurodrive MOVITRAC LTE-B User manual

*21326991_0515*
Drive Technology \ Drive Automation \ System Integration \ Services
Manual
MOVITRAC®LTE-B/LTP-B
Accessories
Keypads, Parameter Module, Cable Sets
Edition 05/2015 21326991/EN

SEW-EURODRIVE—Driving the world

Table of contents
Manual – Accessories 3
Table of contents
1General information .................................................................................................................. 5
1.1 About this documentation ............................................................................................... 5
1.2 Rights to claim under limited warranty ........................................................................... 5
1.3 Other applicable documentation .................................................................................... 5
1.4 Copyright notice ............................................................................................................. 5
2System overview ....................................................................................................................... 6
2.1 System overview of MOVITRAC® LTE-B ....................................................................... 6
2.2 System overview of MOVITRAC® LTP-B ....................................................................... 7
3Parameter module ..................................................................................................................... 8
3.1 Parameter module .......................................................................................................... 8
3.1.1 Technical data................................................................................................. 8
3.2 Installation, startup, and operation ................................................................................. 9
3.2.1 Directly at the frequency inverter .................................................................... 9
3.2.2 With LT Shell software .................................................................................. 11
4Keypad...................................................................................................................................... 14
5Remote keypads ...................................................................................................................... 15
5.1 LT BG-C remote keypad .............................................................................................. 15
5.1.1 Installation in the control cabinet or control panel......................................... 16
5.1.2 Technical data............................................................................................... 17
5.1.3 Display messages......................................................................................... 17
5.2 LT ZBG OLED A remote keypad .................................................................................. 18
5.2.1 Installation in the control cabinet or control panel......................................... 18
5.2.2 Technical data............................................................................................... 19
5.2.3 Display messages......................................................................................... 19
5.3 Electrical installation ..................................................................................................... 20
5.4 System structure .......................................................................................................... 21
5.5 Startup .......................................................................................................................... 22
5.5.1 Setting the communication address.............................................................. 22
5.5.2 Changing/monitoring the parameters............................................................ 22
5.5.3 Preset setpoint speed for operation with remote keypad.............................. 22
5.5.4 Speed change in real time mode with remote keypad .................................. 23
5.5.5 Direction of rotation reversal ......................................................................... 24
5.5.6 Lock/enable parameter access ..................................................................... 24
6Network packages ................................................................................................................... 25
6.1 Basic package (cable set A) ......................................................................................... 25
6.2 Extension package (cable set B) .................................................................................. 26
6.2.1 Example ........................................................................................................ 26
6.3 PC engineering package (cable set C) ........................................................................ 27
6.3.1 Example 1 ..................................................................................................... 27
6.3.2 Example 2 ..................................................................................................... 28
6.4 Cable splitter 1 to 2 ...................................................................................................... 29
7Prefabricated cables ............................................................................................................... 30
21326991/EN – 05/2015

Table of contents
Manual – Accessories
4
7.1 Prefabricated cables with RJ45 connector on one end ................................................ 30
7.2 Prefabricated cables with RJ45 connectors on both ends ........................................... 30
8Control boards......................................................................................................................... 31
8.1 OB LT LOCMO control board ....................................................................................... 31
8.1.1 Technical data............................................................................................... 31
8.1.2 Installation..................................................................................................... 32
8.1.3 Startup and operation ................................................................................... 32
8.2 LTZOBLOCMOB control board .................................................................................... 33
8.2.1 Technical data............................................................................................... 33
8.2.2 Installation..................................................................................................... 34
8.2.3 Startup and operation ................................................................................... 34
Index ......................................................................................................................................... 35
21326991/EN – 05/2015

1
General information
About this documentation
Manual – Accessories 5
1General information
1.1 About this documentation
This documentation is an integral part of the product. The documentation is intended
for all employees who perform assembly, installation, startup, and service work on the
product.
Make sure this documentation is accessible and legible. Ensure that persons respon-
sible for the machinery and its operation as well as persons who work on the device
independently have read through the documentation carefully and understood it. If you
are unclear about any of the information in this documentation or require further infor-
mation, contact SEW‑EURODRIVE.
1.2 Rights to claim under limited warranty
Read the information in this documentation. This is essential for fault-free operation
and fulfillment of any rights to claim under limited warranty. Read the documentation
before you start working with the unit!
1.3 Other applicable documentation
This document supplements the operating instructions and limits the application notes
according to the following information. Use this document only together with the oper-
ating instructions.
1.4 Copyright notice
© 2015 SEW‑EURODRIVE. All rights reserved.
Unauthorized reproduction, modification, distribution or any other use of the whole or
any part of this documentation is strictly prohibited.
21326991/EN – 05/2015

2System overview
System overview of MOVITRAC® LTE-B
Manual – Accessories
6
2System overview
2.1 System overview of MOVITRAC® LTE-B
System
overview of
MOVITRAC
® LTE-B
Option cards:
2nd relay output OB LT 2ROUTB
PI controller OB LT PICON-B
2nd signal relay OB LT HAVAC-B
Converter card OB LT VCON A/B
Control board OB LT LOCMO
Line choke HD
Bluetooth
Parameter module
LTBP-C
Gateway:
PROFIBUS DFP21B
EtherCAT DFE24
DeviceNet DFD11
PROFINET DFE32
Ethernet/IP DFE33B
Interbus UFI11A
Braking resistor BW
Output choke HD
(IP20/IP55)
Line
Line filter NF
LT
®
TM
TM
®
Keypad
LT BG-C
Keypad
LT ZBG OLED A
Shell parameter
software with scope
function
Cable set C
USB11A
BW internal
RJ-45
Cable sets
A, B, C
RJ-45
RJ-45
9007205070153099
21326991/EN – 05/2015

2
System overview
System overview of MOVITRAC® LTP-B
Manual – Accessories 7
2.2 System overview of MOVITRAC® LTP-B
System
overview of
MOVITRAC
® LTP-B
Output choke HD
Braking resistor
BW internal
MOVITOOLS
MotionStudio
3 × 200 – 240 V,
3 × 380 – 480 V
3 × 500 – 600 V
1 × 200 – 240 V
Braking resistor BW
Option cards:
Relay outputs
Digital I/O
Encoder card TTL
Encoder card HTL
PROFIBUS
PROFINET
EtherNet/IP
EtherCAT
DeviceNet
MODBUS TCP
POWERLINK
MOVI-PLC /
UOH-/DFx-
Gateway
Keypad
LT BG-C
Keypad
LT ZBG OLED A
Bluetooth
Parameter module
LTBP-C
1 card slot in
inverter
LTX Servo-Erweiterung
LTX H1A, bis BG 3
RJ-45
LT-Shell parameter
software with scope
function
PEAK USB CAN
Dongle
Frequency inverter
IP55 /
IP20
USB11A
RJ-45
RJ-45
Control board
Cable sets
A, B, C
Cabel set C
RJ-45
®
®
TM
TM
OBLT 3ROUT-A
OBLT IO-A
OBLT ENC-A
OBLT ENC-B
LT FP 11A
LT FE 32A
LT FE 33A
LT FE 24A
LT FD 11A
LT FE 31A
LT FE 25A
®
®
Line choke ND Line filter NF
9007208545763979
21326991/EN – 05/2015

3Parameter module
Parameter module
Manual – Accessories
8
3Parameter module
3.1 Parameter module
The parameter module is exclusively designed for operation in the RJ45 port of the
frequency inverter.
Type Part number LTE-B LTP-B
LTBP-C 18241549 X X
X = available − = not available
9007202440910859
• Functionality:
– Saves data from the frequency inverter to the parameter module.
– Saves data simultaneously from both frequency inverter types to the parameter
module.
– Integrated parameter lock. Prevents overwriting of saved parameters if activa-
ted.
– Loads data back from the parameter module to the frequency inverter.
– Bluetooth® interface for communication between engineering software LT Shell
and MOVITRAC® LT or directly with the parameter module.
3.1.1 Technical data
Degree of protection IP20, NEMA 1
Ambient temperature during operation -10 to +50 °C
Range <10 m, EMC dependent
Data transmission Bluetooth®
21326991/EN – 05/2015

3
Parameter module
Installation, startup, and operation
Manual – Accessories 9
3.2 Installation, startup, and operation
3.2.1 Directly at the frequency inverter
1. Check the frequency inverter connection.
2. Remove the protection caps from the parameter module and insert the parameter
module into the frequency inverter slot RJ45.
MOVITRAC
®
LT
1357911
246810
13663204747
[1]
[2]
[3]
[4]
[5]
[6]
13642864139
Status LEDs
[1] Green Steady light Power okay, frequency inverter detected
Flashing Charging processes
[2] Blue Steady light Bluetooth ready
Flashing Bluetooth communication active
[3] [Read parameters]
button
For copying parameters from the frequency inverter to the parameter mod-
ule.
[4] [Write parameters]
button
For copying parameters from the parameter module to the frequency inver-
ter.
[5] Locking switch For locking the parameter module to inhibit overwriting of the parameter set.
The "Copy parameter" function is deactivated.
[6] Parameter module in-
terface
Connection via RJ45 slot at frequency inverter.
Transfer parameter set
Press the button [3] for downloading the data to the parameter module or [4] for up-
loading data to the frequency inverter.
If the frequency inverter display shows PASS-r, the parameter set was successfully
copied to the parameter module.
21326991/EN – 05/2015

3Parameter module
Installation, startup, and operation
Manual – Accessories
10
If the frequency inverter display shows PASS-t, the parameter set was successfully
copied to the frequency inverter.
Locking or unlocking the parameter module
The parameter module is equipped with a locking switch [5] with 2 positions.
1. Locked:
• Parameter set can be read in the LT Shell software.
• Parameter set cannot be changed.
• Parameter set cannot be transferred from the frequency inverter to the parame-
ter module.
2. Unlocked:
• Read and write possible (free memory access).
Frequency inverter display
The parameter module status is displayed on the frequency inverter display.
Display Description
PASS-r The parameter module successful read/saved the frequency inverter
parameters.
OS-Loc The parameter module is locked. Attempt to read parameter from fre-
quency inverter with activated parameter module lock.
FAiL-r The parameter module could not read parameters from the frequen-
cy inverter.
PASS-t The parameter module successfully transferred the parameters to
the frequency inverter. Writing of parameters to the frequency inver-
ter.
FAiL-P The power ratings of the parameter stored in the parameter module
do not match the power ratings of the programmed frequency inver-
ter.
FAiL-t The parameter module could not transfer the parameter set to the
frequency inverter.
no-dAt No parameter data was saved in the parameter module.
dr-Loc The frequency inverter parameters were locked. No new parameter
settings could be transferred. Unlock the parameter set of the fre-
quency inverter.
dr-rUn Frequency inverter is running and cannot accept any new parameter
settings. Stop the frequency inverter before programming.
tyPE-E The parameters for the frequency inverter type saved in the parame-
ter module do not match the frequency inverter type to be program-
med (only writing).
tyPE-F The parameter module does not yet support the programmed fre-
quency inverter type.
21326991/EN – 05/2015

3
Parameter module
Installation, startup, and operation
Manual – Accessories 11
3.2.2 With LT Shell software
Parameterization user interface
A Bluetooth® interface at the PC is required for communication with PC.
[9][8]
[7]
[6][5]
[4][3]
[1] [2]
[10] [11] [12] [13]
12804199691
[1] Tool selection menu:
• Parameter editor
• Drive monitor
• Scope/ Data logger tool
[7] Transfer parameter set from parameter
module
[8] Transfer parameter set to the parameter
module
[9] Parameter display
[2] Shows the units in the network [10] Offline mode
[3] Open, save parameter file [11] Network is scanned for drives.
[4] Set unit to factory setting [12] Starts real time edit mode.
[5] Transfer parameter set from selected drive
(download)
[13] Defines the number of drives that are to be
scanned during scan mode.
[6] Transfer parameter set to the selected drive
(upload)
Proceed as follows to change the parameter values via the PC:
1. Download the software from the SEW‑EURODRIVE website.
2. Check the frequency inverter connection.
3. Remove the protection caps from the parameter module. Insert the parameter
module into the frequency inverter RJ45 slot.
4. Couple the parameter module with the PC via Bluetooth®. Enter the coupling code
("0000") of the parameter module.
5. Select an outgoing port for the parameter module using the PC. This connection is
used by the PC software.
21326991/EN – 05/2015

3Parameter module
Installation, startup, and operation
Manual – Accessories
12
6. Start the software LT-Shell V4.0.exe.
7. The parameter editor is displayed.
8. Select the COM port of the PC/laptop to which the frequency inverter is connected
via the parameter module.
13102428043
9. Choose the communication Bluetooth®.
13642995211
10.Scan the network for existing drives [11].
11.Read the frequency inverter parameter set using the button [5]. Or read the param-
eter module parameter set using the button [7].
21326991/EN – 05/2015

3
Parameter module
Installation, startup, and operation
Manual – Accessories 13
12.Transfer the parameter set from the software to the frequency inverter using the
button [6] or to the parameter module using the button [8].
13.Double-click the parameter you want to change.
14.Enter the new parameter value into the edit box.
21326991/EN – 05/2015

4Keypad
Manual – Accessories
14
4Keypad
Each MOVITRAC® LT inverter is equipped with a keypad as standard, which allows for
operating and setting up the frequency inverter without the use of any further devices.
MOVITRAC®LT
[4]
[5]
[6]
[1]
[2]
[3]
2933664395
[1] 6-digit 7-segment display [4] Navigate key
[2] Start key [5] Up key
[3] Stop/reset key [6] Down key
The keypad has five keys with the following functions:
Key Navigate [4] • Toggle between menus
• Save parameter values
• Display realtime information
Key Up [5] • Increase speed
• Increase parameter values
Key Down [6] • Decrease speed
• Decrease parameter values
Key Stop [3] • Stop drive
• Acknowledge error
Key Start [2] • Enable drive
• Change direction of rotation
If the parameters are set to the factory setting, the <Start> and <Stop> keys of the
keypad are disabled. To release the <Start>/<Stop> keys on the keypad for use, set
parameter P-12 for LTE-B or P1-12 for LTP-B to "1" or "2".
The parameter edit menu can only be accessed by pressing the <Navigate> key [4].
• To toggle between the menu for changing parameters and the realtime display (op-
erating speed/operating current), keep the key pressed for longer than one second.
• To toggle between the operating speed and the operating current of the running
frequency inverter, press the key briefly (for less than one second).
21326991/EN – 05/2015

5
Remote keypads
LT BG-C remote keypad
Manual – Accessories 15
5Remote keypads
The MOVITRAC® LT basic unit has an integrated keypad. Some applications require a
remote keypad of the frequency inverter. The keypad option comes equipped with a
self-adhesive gasket and a 3 m cable, which is plugged into the RJ45 socket of fre-
quency inverter. This option is supplied with 24 V via the RJ45 cable of the frequency
inverter.
The maximum cable length between keypad and frequency inverter is 25 m with shiel-
ded cables. The length of all the cables in the network must not exceed 25 m for un-
shielded cables, and 100 m for shielded cables.
5.1 LT BG-C remote keypad
We offer a 7-segment display keypad as an additional option.
Type Part number LTE-B LTP-B
LT BG-C 18241522 X X
X = available − = not available
3186128779
21326991/EN – 05/2015

5Remote keypads
LT BG-C remote keypad
Manual – Accessories
16
5.1.1 Installation in the control cabinet or control panel
For installing an LT BG-C in the door of a control cabinet or in a control panel, the
metal has to be cut as shown in the illustration below. The installed keypad meets
standard IP54/NEMA 13 if the self-adhesive gasket enclosed in the delivery is used.
c
a
e
d
f
b
3186131467
g
h
[1]
3186133131
[a] 81 mm [f] 3 mm
[b] 67 mm [g] 70 mm
[c] 65 mm [h] 55 mm
[d] 21 mm [1] Recess
[e] 55 mm
21326991/EN – 05/2015

5
Remote keypads
LT BG-C remote keypad
Manual – Accessories 17
5.1.2 Technical data
Unit connections RJ45
Supply voltage DC 24 V ±10%
Supply current 30 mA
Degree of protection IP20 (if not installed in the control cabinet)
IP54 / NEMA 13 (if installed in the control cabi-
net door)
Ambient temperature during opera-
tion
0 to +50 °C
Maximum relative humidity 95%, condensation not permitted
5.1.3 Display messages
The remote keypad displays information for the error code of the connected frequency
inverter in case of a frequency inverter failure or switch-off responses. For a complete
list with codes and information for diagnostics and troubleshooting, refer to the respec-
tive MOVITRAC® LT operating instructions.
The remote keypad uses different messages to display various operating states:
Display message Meaning
SCAN.. The remote keypad scans the network for frequency inverters.
LOAD.. The remote keypad detected frequency inverters in the net-
work. The frequency inverter loads relevant startup informa-
tion.
Err-SC The remote keypad lost the communication connection to the
frequency inverter.
Adr-XX Displays the address of the remote keypad, X = 1 to 63.
21326991/EN – 05/2015

5Remote keypads
LT ZBG OLED A remote keypad
Manual – Accessories
18
5.2 LT ZBG OLED A remote keypad
We offer a full text OLED keypad as an additional option.
Type Part number LTE-B LTP-B
LT ZBG OLED A 28205731 X X
X = available − = not available
9661213707
5.2.1 Installation in the control cabinet or control panel
For installing an LT ZBG OLED in the door of a control cabinet or in a control panel,
the metal has to be cut as shown in the illustration below. The installed keypad meets
standard IP54 / NEMA 13 if the self-adhesive gasket enclosed in the delivery is used.
9288183563
21326991/EN – 05/2015

5
Remote keypads
LT ZBG OLED A remote keypad
Manual – Accessories 19
5.2.2 Technical data
Unit connections RJ45
Supply voltage DC 24 V ±10%
Supply current 30 mA
Degree of protection IP20 (if not installed in the control cabinet)
IP54 / NEMA 13 (if installed in the control cabi-
net door)
Ambient temperature during opera-
tion
-10 to +50 °C
Maximum relative humidity 95%, condensation not permitted
5.2.3 Display messages
The remote keypad displays information for the error code of the connected frequency
inverter in case of a frequency inverter failure or switch-off responses. For a complete
list with codes and information for diagnostics and troubleshooting, refer to the respec-
tive MOVITRAC® LT operating instructions.
The remote keypad uses different messages to display various operating states:
Display message Meaning
Scanning for drive
XX
The remote keypad scans the network for frequency inverters.
LOAD.. The remote keypad detected frequency inverters in the net-
work. The frequency inverter loads relevant startup informa-
tion.
SC-OBS The remote keypad lost the communication connection to the
frequency inverter. Press the <Stop> key to reset. Check the
frequency inverter address.
Select language List to select one of the available languages. To select a lan-
guage, use the <Navigate> key.
Select drive address
XX
Display when selecting the address of the frequency inverter
communicating with the remote keypad.
Select LT-Pad ID Display when selecting the ID of the remote keypad (1 or 2).
This way, 2 remote keypads can be connected to one frequen-
cy inverter or a network consisting of several frequency inver-
ters.
21326991/EN – 05/2015

5Remote keypads
Electrical installation
Manual – Accessories
20
5.3 Electrical installation
The remote keypad can be connected directly to the frequency inverter using a stand-
ard RJ45 cable. Voltage supply and data transmission is realized via the interface.
The socket at the keypad:
8
1
13515899787
[1] Not connected
[2] Not connected
[3] 0 V
[4] RS485- (engineering)
[5] RS485+ (engineering)
[6] +24 V (voltage supply)
[7] Not connected
[8] Not connected
21326991/EN – 05/2015