SHANGRI-LA SLGSLTBESBB User manual

ANTALYA GAS LIFT BED
KING SINGLE
SLGSLTBESBB, SLGSLTBESGB, SLGSLTBESCB

1Top headboard (x1) 1-1 Bottom headboard (x1) 2Footboard (x1)
3Left sideboard (x1) 4Right sideboard (x1) 8Bracket (x1)
9Slat (x24) 10 End cap (x24) 11 Inner cap (x12)
12 Vertical frame slat (x2) 13 Horizontal frame slat (x2) 14 Horizontal beam (x1)
15 Inner vertical
frame slat (x1) 16 Floor mat (x1) 17 Leg support (x2) 18 Corner support (x2)
COMPONENTS

Hardware
AM6 flat washer (x8) BSpring washer (x8) C20mm M6 screw (x8)
D M8 nut (x14) E40mm M7 screw (x10) F20mm M8 screw (x12)
G35mm M8 screw (x17) HM8 flat washer (x35) IProtective pad (x9)
KAllen key (x1) LWrench (x1) MMattress stopper (x2) NHandle grip (x1)

Step 1: Attach the top headboard (1) to the bottom headboard (1-1) by first peeling the cloth
away from the bottom headboard (1-1). Align M8 flat washers (H) over each of the three
holes. Using the Allen key (K), screw through 35mm M8 screws (G).
G (x4) H (x4) K (x1)
ASSEMBLY
Note:
Do not use power tools when assembling this bed as this may cause damage to the
components.
1
1-1
H
G

Step 2: Attach the holes onto the bracket (8) with the holes in the middle of the footboard
(2). Place one M8 flat washer (H) over each of the two holes and using the Allen key (K),
screw through 35mm M8 screws (G).
Secure two protective pads (I) over the bracket (8).
G (x2) H (x2) I (x2) K (x1)
2
8
I
H
G

Step 3: Align the two holes of the bracket on the left sideboard (3) with those of the left side
of the bottom headboard (1-1). Place an M8 flat washer (H) and spring washer (B) over one
of the holes. Using the Allen key (K), secure a 35mm M8 screw (G) through the washers (H,
B). Repeat this process with the other hole.
Repeat this process on the other side of the bottom headboard to connect the right
sideboard (4).
B (x4) G (x4) H (x4) K (x1)
H
B
G
1
2
3
4

Step 4: Connect the other end of the sideboards (3, 4) to the footboard (2) as outlined the
previous step.
Align the four holes of a corner support (18) with the holes at the corner of the left sideboard
(3) and footboard (2). Place an M8 flat washer (H) over each of the holes and using the
Allen key (K), insert and tighten 20mm M8 screws (F).
Repeat this process using the other corner support (18) with the holes at the corner of the
right sideboard (4) and footboard (2).
B (x4) F (x8) G (x4) H (x12) I (x4) K (x1)
1
4
2
3
16
H
B
G
18
H
F
I

Step 5: Align the holes of two leg supports (17) with one inner vertical frame slat (15) as
shown below.
Place an M8 flat washer (H) over one of the holes. Using an Allen key (K), insert and tighten
a 35mm M8 screw (G). Using the wrench (L), secure the underside of the leg support with
an M8 nut (D). Repeat this process again with the remaining holes. This creates the vertical
assembly.
D (x4) G (x4) H (x4) K (x1) L (x1)
15
17
K
G
H
D
L

Step 6: Align the holes on one end of the vertical assembly with those on a horizontal frame
slat (13). Place an M8 flat washer (H) over one of the aligned holes on the side of the
horizontal frame slat (13). Using the Allen key (K), insert and tighten a 40mm M7 screw (E).
Using the wrench (L), secure an M8 nut (D) on the vertical assembly side of the hole.
Repeat this process with the remaining aligned holes and on the other end of the vertical
assembly to secure to the other horizontal frame slat (13).
Insert and connect the horizontal frame slats (13) to the vertical frame slats (12). Align the
holes of the pieces (13, 12) at each connection. Place an M6 flat washer (A) one hole and
using the Allen key (K), secure a 20mm M6 screw (C) through. Repeat until all holes are
secured.
Insert the mattress stoppers (M) onto the top horizontal frame slat (13).
This completes the base frame assembly.
A (x8) C (x8) D (x4) E (x4)
H (x4) K (x1) L (x1) M (x2)
13
13
12
12
15
17
D
A
H
E
C
M
M

Step 7: Align the holes and using the Allen key (K), secure both ends of the horizontal beam
(14) to the left and right sideboard (3, 4) with 20mm M8 screws (F).
F (x4) K (x1)
14
F
F
4
3

Step 8: Place protective pads (I) onto the horizontal beam (14).
Secure the base frame assembly to the bed by aligning the three holes on one of the
vertical frame slats (12) with the holes on the gas lift of the right sideboard (4). Place an M8
flat washer (H) over each hole and using the Allen key (K), secure 40mm M7 screws (E)
through. Using the wrench (L), secure M8 nuts (D) on the underside of the holes.
Repeat this process on the other side with the remaining vertical frame slat (12) and gas lift
on the left sideboard (3).
D (x6) E (x6) H (x6) I (x3) K (x1) L (x1)
E
E
E
H
H
H
D
D
D
I
I
I

Step 9: Secure the end caps (10) onto the holes along the two lengths of the bed. Going
down the bed, connect one slat (9) onto each end cap (10).Connect the inner end of the
slats with inner caps (11).
The result will form twelve rows with two slats each.
Tie the handle grip (N) onto the base frame assembly. This will make it easier to lift the bed
when needed.
9
10
N
9
11

Assembly complete.

Use a soft dry cloth, feather duster or normal furniture polish to clean the bed.
Over extended use, it may be necessary to tighten the fixings from time to time. This is
normal for any flat pack furniture.
CLEANING & CARE

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com