SHANGRI-LA SLSERENCDWA User manual

SERENGETI CHEST
OF DRAWERS
SLSERENCDWA

Failure to follow these basic steps can lead to damage that is not covered by your warranty.
•Read instructions carefully. Ensure no parts are missing.
•Lay out all the components on a soft surface.
•Carefully identify each component, especially those that are similar. The most
common mistake is getting things back to front.
•Do not fully tighten screws (leave slightly loose). When the item is fully assembled,
tighten the screws but do not over tighten.
•Separate and identify each component from the hardware pack and rest each one
in its proper location before fastening.
•Do not, for any reason, use a power tool to assemble this product.
Use of power tools may apply greater than excess force on the
fixtures, causing damage. Warranty is void if power tools have
been used.
•A Phillips head screwdriver (not supplied) is required for assembly.
The user guide enclosed refers to multiple sets of metal slide runners and slide tracks
(pictured above separately).
To avoid any damage to these items during transportation, the slide runners and slide
tracks have been pre-assembled together in pairs. Each pair includes a slide runner and
slide track. Before assembling your new Shangri-La unit, please separate the slide runners
from the slide tracks according to the below instructions.
SAFETY & WARNINGS
Slide Track
Slide runner

Step 1: Extend the slide runners apart from the slide track:
Step 2: Gently press the plastic release lever on the slide runner while pulling the slide
runner and slide track apart from each other:
Step 3: The slide runner and slide track should now be separated. repeat these steps for all
remaining pairs of slide runners and slide tracks:
Slide runner
Slide track

COMPONENTS

Parts list
Hardware
AΦ15x9.6 (x57) BL=35mm (x57) CΦ5.5x38 (x4) DΦ4x32 (x10)
E14" (x10) F14" (x10) GΦ3.5x12 (x60) H(x12)
IΦ3x18 (x12) J Φ6x13x1 (x1) K (x1) L Φ4x16 (x1)
No.
Dimensions (mm)
Qty
No.
Dimensions (mm)
Qty
1 383 x 993 x 15 1 10 60 x 760 x 15 2
2 383 x 993 x 15 1 11 60 x 313 x 15 2
3 400 x 800 x 15 1 12 175 x 796 x 15 5
4 383 x 800 x 15 1 13 118 x 350 x 12 5
5 230 x 777 x 2.5 1 14 118 x 350 x 12 5
6 380 x 777 x 2.5 2 15 116 x 724 x 12 5
7 50 x 796 x 15 1 16 344 x 733 x 2.5 5
8 50 x 768 x 15 4 17 50 x 335 x 12 10
9 80 x 768 x 15 2

Step 1: Repeat this process for all parts labelled 12 and 15.
BL=35mm (x30)
ASSEMBLY

Step 2: Repeat this process for all parts labelled 13 and 14.
F14" (x10) GΦ3.5x12 (x10)
DRAWER SLIDE (F X 5) DRAWER SLIDE (F X 5)

Step 3: Use D screws to secure parts as shown. Use a Phillips head screwdriver to secure A
to B for part 12.
Repeat this process for all five drawers.
AΦ15x9.6 (x10) DΦ4x32 (x10)
Arrow to point in
the direction of
end hole

Step 4: Repeat this process for all five drawers.
AΦ15x9.6 (x20)
Arrow to point in
the direction of
end hole

Step 5:
E14" (x10) GΦ3.5x12 (x30)
DRAWER SLIDE (E X 10)

Step 6:
BL=35mm (x12)

Step 7:
BL=35mm (x7)

Step 8:
AΦ15x9.6 (x3)
Arrow to point in
the direction of
end hole

Step 9:
BL=35mm (x4)
Step 10: Repeat this process twice for parts labelled 10.
BL=35mm (x4)

Step 11:
AΦ15x9.6 (x4)
Arrow to point in
the direction of
end hole

Step 12:
AΦ15x9.6 (x6)
Arrow to point in
the direction of
end hole

Step 13:
AΦ15x9.6 (x6)
Arrow to point in
the direction of
end hole

Step 14:
CΦ5.5x38 (x4)

Step 15:
AΦ15x9.6 (x4)
Arrow to point in
the direction of
end hole