SHANGRI-LA ROBIN SLROBI6CDWA User manual

ROBIN CHEST OF 6
DRAWERS
SLROBI6CDWA & SLROBI6CDBA

Please read these safety instructions thoroughly before using this product. Retain this guide
for future reference.
• Carefully identify each component, especially those that are similar. The most
common mistake is getting things back to front.
• Separate and identify each component from the hardware pack and rest it in its
final location before fastening.
• Do not fully tighten screws (leave slightly loose). When the item is fully assembled
tighten the screws - but do not over tighten.
• If glue is required, do not set until you are certain that the parts belong together.
SAFETY & WARNINGS

Lay all components out on a clean floor and ensure all parts are included. If any pieces are
missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.
Parts:
COMPONENTS

No.
Size (mm)
Qty
No.
Size (mm)
Qty
1
60 x 395 x 40
1
15
46 x 628 x 15
4
2
60 x 395 x 40
1
16
50 x 1052 x 15
2
3
60 x 395 x 40
1
17
50 x 224 x 15
1
4
60 x 395 x 40
1
18
80 x 145 x 15
1
5
394 x 585 x 15
1
19
80 x 145 x 15
4
6
394 x 585 x 15
1
20
190 x 624 x 15
1
7
394 x 1222 x 15
1
21
190 x 624 x 15
1
8
394 x 1222 x 15
1
22
190 x 624 x 15
6
9
393 x 633 x 15
1
23
130 x 350 x 12
6
10
323 x 659 x 2.5
2
24
130 x 350 x 12
6
11
323 x 659 x 2.5
1
25
128 x 584 x 12
6
12
323 x 659 x 2.5
1
26
344 x 593 x 2.5
6
13
46 x 628 x 15
1
27
50 x 335 x 12
6
14
46 x 628 x 15
1
Hardware:
AØ15x9.6 (x63)
B35mm (x57)
CØ4x25 (x12)
DØ4x32 (x12)
E14" (x12)
F14" (x12)
GØ3.5x12 (x72)
H(x40)
IØ5.5x38 (x7)
JLegs (x4)
KØ5x16x1
L
MØ5x16 (x6)
NØ632 (x2)
O68mm (x3)

IMPORTANT! Read before assembling
This product contains multiple sets of metal slide runners and slide tracks (shown separated
above).
To a v o i d damage to these items during transportation, the slide runners and tracks have
been pre-assembled together in pairs. Each pair includes one slide runner and one slide
track.
Before assembling your furniture, separate the runners from the tracks according to the
following instructions:
• Extend the slide runners.
• Gently press the plastic release lever on the slide runner while pulling the slide
runner and slide track apart from each other.
• The slide runner and slide track should now be separated. Repeat these steps for
the remaining pairs of slide tracks:
ASSEMBLY
Slide runner
Slide track

Step 1:
B 35mm (x24)

Step 2:
F14" (x12)
GØ3.5x12 (x36)
x6 Drawer Slides F
x6 Drawer Slides F

Step 3:
AØ15x9.6 (x8)
DØ4x32 (x12)
Arrow to point in
the direction of
end hole

Step 4:
AØ15x9.6 (x8)
Step 5:
AØ15x9.6 (x2)
Arrow to point in
the direction of
end hole
Arrow to point in
the direction of
end hole

Step 6:
AØ15x9.6 (x2)
Step 7:
AØ15x9.6 (x2)
Arrow to point in
the direction of
end hole
Arrow to point
in the direction
of end hole

Step 8:
AØ15x9.6 (x2)
Step 9:
B35mm (x6)
Arrow to point
in the direction
of end hole

Step 10:
E14" (x6)
GØ3.5x12 (x18)
x6 Drawer Slide E

Step 11:
E14" (x3)
GØ3.5x12 (x9)
Left side
x3 Drawer Slide E

Step 12:
E14" (x3)
GØ3.5x12 (x9)
Right side
x3 Drawer Slide E

Step 13:
AØ15x9.6 (x6)
O68mm (x3)
Arrow to point in
the direction of
end hole

Step 14:
AØ15x9.6 (x3)
Arrow to point
in the direction
of end hole

Step 15:
AØ15x9.6 (x3)
Arrow to point
in the direction
of end hole

Step 16:
CØ4x25 (x6)
Step 17:
B35mm (x10)

Step 18:
KØ5x16x1
L
MØ5x16
Step 19:
CØ4x25 (x6)