SHANGRI-LA SERENGETI SLSERENDCWA User manual

SERENGETI
CONSOLE/ DESK
SLSERENDCWA

Failure to follow these basic steps can lead to damage that is not covered by your warranty.
•Read instructions carefully. Ensure no parts are missing.
•Lay out all the components on a soft surface.
•Carefully identify each component, especially those that are similar. The most
common mistake is getting things back to front.
•Do not fully tighten screws (leave slightly loose). When the item is fully assembled,
tighten the screws but do not over tighten.
•Separate and identify each component from the hardware pack and rest each one
in its proper location before fastening.
•Do not, for any reason, use a power tool to assemble this product.
Use of power tools may apply greater than excess force on the
fixtures, causing damage. Warranty is void if power tools have
been used.
•A Phillips head screwdriver (not supplied) is required for assembly.
The user guide enclosed refers to multiple sets of metal slide runners and slide tracks
(pictured above separately).
To avoid any damage to these items during transportation, the slide runners and slide
tracks have been pre-assembled together in pairs. Each pair includes a slide runner and
slide track. Before assembling your new Shangri-La unit, please separate the slide runners
from the slide tracks according to the below instructions.
SAFETY & WARNINGS
Slide Track
Slide runner

Step 1: Extend the slide runners apart from the slide track:
Step 2: Gently press the plastic release lever on the slide runner
while pulling the slide runner and slide track apart from each
other:
Step 3: The slide runner and slide track
should now be separated. repeat these
steps for all remaining pairs of slide runners
and slide tracks:

COMPONENTS

Parts list
Hardware
AΦ15x9.6 (x6) BL=35mm (x6) CΦ4x32 (x2) D12" (x2)
E12" (x2) FΦ3.5x12 (x8) GΦ6x13x1 (x1) H(x1)
IΦ4x16 (x1) JΦ15x11.5 (x14) KL=38mm (x14)
No. Dimensions (mm) Qty
No. Dimensions (mm) Qty
1 348 x 767 x 28 1 7 80 x 300 x 12 1
2 348 x 767 x 28 1 8 80 x 300 x 12 1
3 350 x 1000 x 28 1 9 78 x 896 x 12 1
4 290 x 340 x 15 1 10 294 x 905 x 2.5 1
5 80 x 340 x 15 1 11 50 x 285 x 12 2
6 115 x 934 x 15 1

Step 1:
BL=35mm (x6)
ASSEMBLY

Step 2:
F12" (x2) GΦ3.5x12 (x4)
DRAWER SLIDE (E X 1) DRAWER SLIDE (E X 1)

Step 3: Use D screws to secure parts as shown. Use a Phillips head screwdriver to secure A
to B for part 6.
AΦ15x9.6 (x2) DΦ4x32 (x2)
Arrow to point in
the direction of
end hole

Step 4:
AΦ15x9.6 (x4)
Arrow to point in
the direction of
end hole

Step 5:
E12" (x2) GΦ3.5x12 (x4)
DRAWER SLIDE (D X 2)

Step 6:
KL=38mm (x8)

Step 7:
KL=38mm (x6)

Step 8:
JΦ15x11.5 (x8)
Arrow to point
in the direction
of end hole

Step 9:
JΦ15x11.5 (x6)
Arrow to point
in the direction
of end hole

Step 10:

Step 11:
GΦ6x13x1 (x1) H(x1) IΦ4x16 (x1)
TOPPLING FURNITURE WARNING:
• It is strongly recommended that this product is permanently fixed to the wall.
• Please seek professional advice if you are in doubt of what fixing device to use.
• Regularly check that anchors are securely maintained.
• Stability of tall items may be affected by thick carpets or uneven floors.
• Do not place unanchored televisions on furniture.
Caution! For your safety when attaching the anchor fixings, please note the
following: Check any electrical wires or plumbing inside the wall before drilling
any holes (if you are unsure, please seek professional advice from a qualified
tradesperson).

Step 12:
Move the drawer chest to the final position. Attach the safety strap to the wall.
Make sure it is firmly attached and make sure it is snugly fit.

Assembly complete.

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com