SHANGRI-LA SLMANILCDWA User manual

MANILA CHEST OF DRAWERS
SLMANILCDWA, SLMANILCDBA, SLMANILCDNA

Ensure to read all instructions and warnings in this user guide prior to assembly.
•Ensure no parts are missing. If parts are missing, contact help.Kogan.com for
assistance.
•Lay out all the components on a soft surface.
•Carefully identify each component, especially those that are similar. The most
common mistake is getting things back to front.
•Do not fully tighten screws (leave slightly loose) during assembly. When the item is
fully assembled, tighten the screws but do not overtighten.
•Separate and identify each component from the hardware pack and rest each one in
its proper location before fastening.
•Do not, for any reason, use a power tool to assemble this product. Use of power tools
may apply excess force on the fixtures, causing damage.
•A Phillips screwdriver (not supplied) is required for assembly.
The user guide enclosed refers to multiple sets of metal slide runners and slide tracks
(pictured above separately).
To avoid any damage to these items during transportation, the slide runners and slide
tracks have been pre-assembled together in pairs. Each pair includes a slide runner and
slide track. Before assembling your new Shangri-La unit, please separate the slide runners
from the slide tracks according to the following instructions.
SAFETY & WARNINGS
Slide track
Slide runner

Step 1: Extend the slide runners apart
from the slide track.
Step 2: Gently press the plastic release
lever on the slide runner while pulling
the slide runner and slide track apart
from each other.
Step 3: The slide runner and slide track
should now be separated. repeat these
steps for all remaining pairs of slide
runners and slide tracks.

COMPONENTS

Parts list
No Dimensions (mm) Qty No Dimensions (mm) Qty
1 340 x 865 x 15 1 8 217 x 731 x 50 3
2 340 x 865 x 15 1 9 217 x 731 x 50 1
3 394 x 738 x 25 1 10 148 x 300 x 12 4
4 340 x 737 x 15 1 11 148 x 300 x 12 4
5 424 x 704 x 12 2 12 146 x 661 x 12 4
6 80 x 705 x 15 1 13 294 x 670 x 2.5 4
7 80 x 705 x 15 1 14 50 x 285 x 12 8
Hardware
AΦ15x9.6 (x56) BL=35mm (x56) CΦ5.5x38 (x4) D Φ4x32 (x8)
E12" (x8) F12" (x8) GΦ3.5x12 (x40) H 25x340x105 (x2)
IL=4mm (x1) JΦ6x13x1 (x5) KΦ4x16 (x1) L (x1) MΦ6x30 (x4)

Step 1: Insert B onto the four parts labelled 12, three parts labelled 8, and one part labelled
9.
BL=35mm (x32)
ASSEMBLY

Step 2: Repeat this process to all four parts labelled 10, and four parts labelled 11.
F12" (x8) GΦ3.5x12 (x16)
DRAWER SLIDE (F x 4) DRAWER SLIDE (F x 4)

Step 3: Using a Phillips screwdriver, secure D screws as shown below. Repeat this process
three more times. This will create four drawer assemblies.
With one drawer assembly, secure A to B for part 8. Repeat this process two more times.
There will be one drawer assembly leftover.
AΦ15x9.6 (x12) DΦ4x32 (x8)
Arrow to point in
the direction of
end hole

Step 4:
AΦ15x9.6 (x4)
Arrow to point in
the direction of
end hole

Step 5:
AΦ15x9.6 (x16)
Arrow to point in
the direction of
end hole
Arrow to point in
the direction of
end hole

Step 6:
E12" (x8) GΦ3.5x12 (x16)
DRAWER SLIDE (E x 8)

Step 7:
BL=35mm (x12)

Step 8:
BL=35mm (x4)

Step 9:
AΦ15x9.6 (x2)
Arrow to point in
the direction of
end hole

Step 10:
AΦ15x9.6 (x2)
Arrow to point in
the direction of
end hole

Step 11:
AΦ15x9.6 (x6)
Arrow to point in
the direction of
end hole

Step 12:
AΦ15x9.6 (x6)
Arrow to point in
the direction of
end hole

Step 13:
BL=35mm (x2)

Step 14:
AΦ15x9.6 (x2) CΦ5.5x38 (x4)
Arrow to point in
the direction of
end hole