SHANGRI-LA MANILA ENTERTAINMENT UNIT SLMANILESWA User manual

MANILA ENTERTAINMENT UNIT
120CM
SLMANILESWA, SLMANILESNA, SLMANILESBA

Ensure to read all instructions and warnings in this user guide prior to assembly.
•Ensure no parts are missing. If parts are missing, contact help.Kogan.com for
assistance.
•Lay out all the components on a soft surface.
•Carefully identify each component, especially those that are similar. The most
common mistake is getting things back to front.
•Do not fully tighten screws (leave slightly loose) during assembly. When the item is
fully assembled, tighten the screws but do not overtighten.
•Separate and identify each component from the hardware pack and rest each one in
its proper location before fastening.
•Do not, for any reason, use a power tool to assemble this product. Use of power tools
may apply excess force on the fixtures, causing damage.
•A Phillips screwdriver (not supplied) is required for assembly.
The user guide enclosed refers to multiple sets of metal slide runners and slide tracks
(pictured above separately).
To avoid any damage to these items during transportation, the slide runners and slide
tracks have been pre-assembled together in pairs. Each pair includes a slide runner and
slide track. Before assembling your new Shangri-La unit, please separate the slide runners
from the slide tracks according to the following instructions.
SAFETY & WARNINGS
Slide track
Slide runner

Step 1: Extend the slide runners apart
from the slide track.
Step 2: Gently press the plastic release
lever on the slide runner while pulling
the slide runner and slide track apart
from each other.
Step 3: The slide runner and slide track
should now be separated. repeat these
steps for all remaining pairs of slide
runners and slide tracks.
To adjust your doors to make the gaps more even (optional):
Step 1: Open the door.
Top panel
Door
Side panel

Step 2: Adjust the gap between the door and side panel.
Loosen the screw slightly. Adjust the hinge to the right position (see steps 2a & 2b). then
tighten the screw.
Step 2a: Move the door in Step 2b: Move the door out
Push the hinge back slightly. Pull the hinge forward slightly.
Top panel Top panel
Gap too large
Top panel
Top panel
Door
Side panel
Top panel
Gap too small
Top panel
Door
Side panel
Top panel
Side panel
Door

Step 3:Adjust the gap between the two doors.
Loosen or tighten the screw slightly to adjust the gap between the door panels (see step 3a
& step 3b).
Step 3a: Move the door right Step 3b:Move the door left
Turn the screw clockwise as shown
to make the gap smaller.
Turn the screw anticlockwise as
shown to make the gap bigger.
Door
Side panel
Side panel
Top panel
Door Door
Gap too large Gap too small
Top panel
Top panel
Top panel
Side panel
Door

COMPONENTS

Parts list
No Dimensions (mm) Qty
1 285 x 350 x 15 1
2 285 x 350 x 15 1
3 285 x 350 x 15 1
4 285 x 350 x 15 1
5 394 x 1200 x 25 1
6 340 x 1199 x 15 1
7 322 x 616 x 15 1
8 269 x 294 x 2.5 2
9 294 x 626 x 2.5 1
10 297 x 1193 x 51 1

Hardware
AΦ15x9.6 (x8) BL=35mm (x8) C Φ5.5x38 (x8) DΦ35mm (x3)
EΦ4x15 (x16) F(x2) G Φ3.5x15 (x4) H(x12)
IΦ3x18 (x12) JΦ6x13x1 (x9) K Φ4x16 (x1) L(x1)
MΦ6x30 (x6) N25x340x105 (x2) O Φ=4mm (x1) PΦ6x35 (x2)
Q
15x25x1050 (x1)
R
(x2) SΦ4x25 (x4) T(x4)
UΦ3.4x10 (x4) V Φ20mm (x15)
W
5.4x10 (x2)

Step 1: Use a Phillips screwdriver (not supplied) to secure the C screws as shown.
CΦ5.5x38 (x8)
ASSEMBLY

Step 2:
N25x340x105 (x2) OΦ=4mm (x1) P Φ6x35 (x2) JΦ6x13x1 (x2) Q 15x25x1050 (x1)

Step 3:
OΦ=4mm (x1) M Φ6x30 (x6) JΦ6x13x1 (x6)

Step 4:
BL=35mm (x8)

Step 5:
GΦ3.5x15 (x4)
F
(x2)

Step 6: Use a Phillips screwdriver (not supplied) to secure A to B for part 5.
AΦ15x9.6 (x8)
Arrow to point
in the direction
of end hole

Step 7: Secure T support pegs with U screws to the desired level in the four corners between
parts 3 and 4. Place part 7 on top of the T support pegs.
T(x4) U Φ3.5x10 (x4)

Step 8:
DΦ35 (x3) E Φ4x15 (x12) W5.4x10 (x2)

Step 9: Secure R to part 10 using S screws, and to parts 3 and 4 using E screws.
Cover the exposed screw holes and A nuts with V.
R(x2) SΦ4x25 (x4) E Φ4x15 (x4) V Φ20mm (x15)

Step 10:
H(x12) IΦ3x18 (x12)

Step 11:
J(x9) K Φ4x16 (x1) L(x1)