Shark S3251 Series User manual

OWNER’S GUIDE
LIGHT & EASY™STEAM MOP
S3251 Series

11-800-798-7398
WHEN USING YOUR SHARK®STEAM MOP,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK® STEAM MOP.
DANGER OF SCALDING.
Please use caution when using the steam
mop. The steam emitted from the steam
mop is very hot.
IMPORTANT:
This appliance is not intended for use by
persons with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for their
safety.
Children shall not use or play with this
appliance. Close supervision is necessary to
keep appliance out of reach of children during
use and cooling.
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1Use the system only for its intended use.
2DO NOT use outdoors.
3 DO NOT leave the appliance unattended when
plugged in. Always unplug the power cord from the
electrical outlet when not in use and before servicing.
4DO NOT allow the appliance to be used by children.
Close attention is necessary when used near
children, pets or plants.
5Use only as described in this manual.
6Use only manufacturer’s recommended accessories.
7DO NOT use with damaged cord or plug.
8DO NOT USE if the appliance is not working, has
been dropped, dropped into water, damaged or
left outdoors.
9NO SERVICEABLE PARTS. Incorrect re-assembly
or repair can cause a risk of electrical shock or injury
to persons when the appliance is used. Contact
Customer Service.
10 To protect against a risk of electric shock, DO NOT
immerse the steam mop into water or any other liquids.
11 DO NOT handle plug or steam mop with wet hands
or operate appliance without shoes.
12 DO NOT pull or carry by power cord, use power cord
as handle, close a door on the power cord, or pull
the power cord around sharp edges or corners. Keep
power cord away from heated surfaces.
13 DO NOT unplug by pulling on power cord. To unplug,
grasp the plug not the power cord. Do not use
extension cords or outlets with inadequate current
carrying capacity.

2www.sharkninjamanuals.com
14 DO NOT put any objects into openings. Do not use
with any opening that is blocked.
15 DO NOT put hands or feet under the steam mop. Unit
gets very hot.
16 Use ONLY on flat, horizontal surfaces. Do not use on
walls, counters or windows.
17 DO NOT use on leather, wax polished furniture or
floors, synthetic fabrics, velvet or other delicate,
steam sensitive materials.
18 Liquid or steam must not be directed towards
equipment containing electrical components, such as
the interior of ovens.
19 DO NOT add cleaning solutions, scented perfumes,
oils or any other chemicals to the water used in this
appliance as this may damage the unit or make it
unsafe for use. If you live in a hard water area, we
recommend using distilled water in your steam mop.
20 When in use, NEVER turn the appliance over or
on its side. NEVER DIRECT STEAM TOWARDS
PEOPLE, ANIMALS OR PLANTS.
21 NEVER LEAVE THE STEAM MOP IN ONE SPOT
ON ANY SURFACE FOR ANY PERIOD OF TIME
WHEN THE CLEANING PAD IS ATTACHED AS
THIS WILL DAMAGE YOUR FLOORS.
22 Carefully remove the cleaning pad immediately after
you have unplugged and allowed the steam mop to
cool.
23 When cleaning the steam mop, unplug the power
cord from the electrical outlet and clean with a dry
or damp cloth. Do not pour water or use alcohol,
benzene or paint thinner on the unit.
24 Extreme caution should be exercised when using this
appliance to clean stairs.
25 Never use steam mop without the cleaning pad
attached.
26 Keep your work area well lit.
27 Store steam mop indoors in a cool, dry place.
28 To avoid circuit overload, do not operate another
appliance on the same socket (circuit) as the steam
cleaner.
29 If an extension cord is absolutely necessary, an
extension cord rated a minimum of 15 ampere,
2.08mm2(14 AWG) cord should be used. Cords rated
for less amperage may overheat. Care should be
taken to arrange cord so that it cannot be pulled or
tripped over.
30 DO NOT leave unattended when the system is
connected to a power supply or electrical outlet. Turn
off all controls before unplugging the unit.
31 DO NOT store unit with damp or wet cleaning pad
attached. Never leave the steam mop in one spot on
any surface for any period of time with a damp or
wet cleaning pad attached as this will damage your
floors.
32 Always unplug and allow the steam mop to cool
before removing or changing mop heads.
33 Make sure that the water tank door is closed when
using the appliance.
WARNING: Your steam mop is designed
to clean hard floor surfaces that will withstand high
heat. Do not use on unsealed wood or unglazed
ceramic floors. On surfaces that have been treated
with wax or some no wax floors, the sheen may
be removed by the heat and steam action. It is
always recommended to test an isolated area of
the surface to be cleaned before proceeding. We
also recommend that you check the use and care
instructions from the floor manufacturer.
SAVE THESE
INSTRUCTIONS

31-800-798-7398
THIS BOOK COVERS MODEL NUMBER:
S3251**** 11
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50/60Hz
Power: 1550 Watts
Water Capacity: 250 ml (8 oz.)
IPX4
This appliance complies with the WEEE-Directive 2012/19/EU on the disposal of electrical and electronic
equipment (WEEE).
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of material sources. To return
your used device, please use the return and collection systems or contact the retailer where this
product was purchased. They can take this product for environmental safe recycling.
This appliance complies with the European directives for electromagnetic compatibility (EMC) 2004/108/EC and its
revisions, as well as Low Voltage Directive (LVD) 2006/95/EC and its revisions.
This product has no on/off switch and operates when plugged into the main supply source. Disconnect the plug
from mains after use.
Although the product is not provided with standby mode or off mode, it still fulfills the requirements of 1275/2008/
EC - the directive for Eco-Design requirements since according to technical justification, it is considered as
inappropriate to provide standby and off modes when connecting to mains. To reduce energy consumption be sure
to unplug the unit after use.

4www.sharkninjamanuals.com
Contents
Getting Started ..................................................................................................... 5
Using Your Light & Easy™Steam Mop..................................................................... 8
Care of Your Light & Easy™Steam Mop ................................................................ 11
Troubleshooting .................................................................................................. 12
Warranty ............................................................................................................ 13
Thank you for
purchasing the
Shark®Light &
Easy™Steam
Mop.

51-800-798-7398
b
Getting Started
FIRST THINGS FIRST, YOU NEED TO KNOW
WHAT’S IN THE BOX YOU JUST OPENED:
aUpper Extension Tube
bLower Extension Tube (Telescopic)
cSteam Mop Base
d2 All-Purpose Cleaning Pads
eFilling Flask
ASSEMBLY
1 Remove all the parts from the package. Verify all the
listed parts are included.
2Slide the upper extension tube (the tube with the
handle) into the lower extension tube (the short
tube). Push the two extension tubes together in until
you hear it click into place. (fig. 1)
When assembling your steam mop there may be a little
water in or around the water tank. This is because we
test all our steam mops 100% before you buy them, so
you get a quality Shark®Light & Easy™Steam Mop.
fig. 1
a
b
c
d
e

6www.sharkninjamanuals.com
IMPORTANT: Never use the Light & Easy™
Steam Mop without attaching a microfibre
cleaning pad to avoid damage to your floor and
mop.
IMPORTANT: Do not use on unsealed wood
or unglazed ceramic floors. On surfaces that
have been treated with wax or some no wax
floors, the sheen may be removed by the heat
and steam action. It is always recommended
to test an isolated area of the surface to be
cleaned before proceeding. We recommend
that you check the use and care instructions
from the floor manufacturer.
3Insert the assembled handle piece into the steam
mop base. Push the tube base together until you
hear a click. (fig. 2)
4For your comfort, you can adjust the height of the
mop. Just lift the latch on the tube 90 degrees to the
open position. Holding the handle, extend the tube
to the desired height and then close the latch to the
locked position. (fig. 3)
QUICK TIP: For easier pushing and pulling, extend
the handle length.
fig. 2
fig. 3

71-800-798-7398
ATTACHING THE MICROFIBRE PAD
1Place the microfibre cleaning pad on the floor with
the quick fastener strips facing up. Place the Light
& Easy™Steam Mop on the top of the pad to attach.
(fig. 4)
IMPORTANT: Only add water to the tank.
Chemicals or cleaning solutions may be
unsafe or cause damage.
IMPORTANT: Please wait 3-5 minutes for your
Light & Easy™Steam Mop to cool off before
removing the microfibre pad.
Getting Started
FILLING THE WATER TANK
IMPORTANT: Unplug the Light & Easy™Steam
Mop before filling the water tank with water.
1Remove the water tank cap by turning it counter-
clockwise to the unlocked position. (fig. 5)
2A filling flask is included with your Light & Easy™
Steam Mop to make filling the water tank easy. Fill
the flask with water and pour it into the tank. Keep
the water level under the MAX’ fill line.
3Replace the water tank cap and turn it clockwise to
the locked position.
fig. 4 fig. 5
Your microfibre cleaning pads should be replaced
every 3 months to maximize cleaning performance.
Calcium and mineral deposits can build up and
impact the performance of your steam mop
over time. To extend the life of your product we
recommend that you use distilled water.

8www.sharkninjamanuals.com
IMPORTANT: Your steam mop needs water
to make steam! Never use your steam mop
without water in the tank.
Sweep or vacuum your floors prior to cleaning with
your Light & Easy™Steam Mop.
Using Your Light & Easy™Steam Mop
1 Pull and twist the quick release cord holder to
unwrap the power cord completely. (fig. 6) Plug into
a 220-240 volt electrical outlet. The “On” light will
turn blue. If the light does not turn on, reference the
troubleshooting section on page 12. (fig. 7)
When you use your steam mop for the first time or
if you have not used the unit in awhile, it may take a
minute or two for the water to travel through the pump
and into the heater to create steam. Get it started by
pumping the handle a few times. If you have waited a few
minutes and you still do not see any steam, reference the
troubleshooting section on page 12.
fig. 6
fig. 7

91-800-798-7398
Using Your Light & Easy™Steam Mop - cont.
2Wait 30 seconds for the boiler to heat the water.
Pump the handle a few times to prime the pump,
activate steam and moisten the microfibre pad.
(fig. 8)
3Mop with a forward and backward motion to
customize steam output automatically. (fig. 9)
IMPORTANT: Never leave the Light & Easy™
Steam Mop with a damp/wet microfibre pad
on any floor surface for any amount of time as
this may damage the floor.
fig. 8
fig. 9
If your Light & Easy™ Steam Mop stops
steaming, it could be out of water. Unplug the
power cord from the electrical outlet and refill
the water tank at anytime.

10www.sharkninjamanuals.com
4To store the cooled Shark®Light & Easy™Steam
Mop, hang on a large hook. (fig. 11)
NOTE: If you want to store the Light & Easy™Steam
Mop standing upright, make sure it is leaning
against a wall for added support and safety. Always
store your Shark®Light & Easy™Steam Mop with
the microfibre cleaning pad removed. Store away
from children and high traffic areas.
Care of Your Light & Easy™Steam Mop
AFTER USE AND STORAGE
1When you have finished using the Light & Easy™
Steam Mop, unplug the cord from the outlet and
place the mop into the upright position and let the
unit cool 3-5 minutes. Release steam by pumping
the handle several times.
2Carefully separate microfibre cleaning pad from
steam mop, avoiding contact with the hot pad or
dirt. (fig. 10)
3Empty the water tank before storage. Remove the
water tank cap and empty the tank over a sink.
Replace the water cap.
fig. 10 fig. 11

11 1-800-798-7398
CARE OF YOUR MICROFIBRE CLEANING
PADS
1 We recommend washing your microfibre cleaning
pads separately from other fabrics to avoid picking
up lint. Only use liquid detergent (no powder
detergent). Don’t use any fabric softeners or bleach.
Line dry. Do not tumble dry. (fig. 12)
Care of Your Light & Easy™Steam Mop
fig. 12
fig. 13
40°
2If there are loose threads on the microfibre cleaning
pad carefully cut the thread with scissors. Don’t pull
on them or cut at the base. (fig. 13)
IMPORTANT: The microfibre cleaning pad may
be very hot from the steam. Use caution when
removing. Let the unit cool for 2-3 minutes.

12www.sharkninjamanuals.com
Trouble Shooting
PROBLEM POSSIBLE REASONS & SOLUTIONS
The Light & Easy™Steam Mop
will not turn-on.
Your steam mop should be securely plugged into an electrical outlet only.
Check your fuse or breaker.
Light & Easy™Steam Mop
will
not make steam.
Is there water in the water tank? If not, add water to your steam mop following
instructions on page 7.
Light & Easy™Steam Mop
leaves water on the floor.
Check to see if your cleaning pad is too wet. We recommend you unplug the
steam mop and change the cleaning pad.
Make sure the cleaning pad is attached correctly.
Light & Easy™Steam Mop
left
white spot on the floor.
Do not leave your steam mop on the floor with a damp or wet cleaning pad.
If you’re using tap water, we recommend switching to distilled water.
Make sure the cap is secured on the water tank.
Floors are cloudy, streaky or
spotty after steaming.
The cleaning pad might be dirty. Change the cleaning pad.
If you washed the cleaning pad with powder detergent, then your pad could be
damaged and require replacement.
This could also be an indication of prior soap or grease residue that has
accumulated on the floor. As our steam mops use only a small amount of
water, it may not be wet enough to rinse off the accumulation that the steam
is bringing to the surface. We suggest rinsing the floor with nothing but water,
letting it dry, and then steam mopping again with a clean pad. One or more
rinses generally removes the residue.
A more stubborn case may require you to rinse the floor with a mix of one part
vinegar and two parts water.
Light & Easy™Steam Mop
is
hard to push.
Make sure the steam pad is attached correctly.
Check to see if the cleaning pad is excessively dirty. Replace if the pad is too
dirty or wet.

13 1-800-798-7398
PRODUCT REGISTRATION
Please visit www.sharkninjamanuals.com or call 1-800-798-7398 to register your new Shark®product within ten
(10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your
name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you
acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instruc-
tions.
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of one
(1) year from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions
and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option.
This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or
used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling
or damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or defects
caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which
have been performed by a repair person not authorized by EURO-PRO Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period,
return the complete appliance and accessories, freight prepaid. For assistance with warranty service options or customer
support, please call our customer care and product specialists at , call 1 [phone] or visit our website www.
sharkninjamanuals.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it
free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return freight. *
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations
expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for
incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state
or from province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date
and to attach tag to item before packing with your name, complete address and phone number with a note
giving purchase information, model number and what you believe is the problem with the item. We recom-
mend you insure the package (as damage in shipping is not covered by your Limited Warranty). Mark the
outside of your package “ATTENTION CUSTOMER SERVICE”.
**THIS WARRANTY IS FOR ALL COUNTRIES EXCEPT GERMANY**

14www.sharkninjamanuals.com
PRODUCT REGISTRATION
Please visit www.sharkninjamanuals.com or call 1-800-798-7398 to register your new Shark®product within ten
(10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your
name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you
acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instruc-
tions.
TWO (2) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of two
(2) years from the date of purchase when utilized for normal household use, subject to the following conditions, exclu-
sions and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option.
This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or
used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling
or damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or defects
caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which
have been performed by a repair person not authorized by EURO-PRO Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period,
return the complete appliance and accessories, freight prepaid. For assistance with warranty service options or customer
support, please call our customer care and product specialists at , call 1 [phone] or visit our website www.
sharkninjamanuals.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it
free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return freight. *
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations
expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for
incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state
or from province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date
and to attach tag to item before packing with your name, complete address and phone number with a note
giving purchase information, model number and what you believe is the problem with the item. We recom-
mend you insure the package (as damage in shipping is not covered by your Limited Warranty). Mark the
outside of your package “ATTENTION CUSTOMER SERVICE”.
**THIS WARRANTY IS FOR GERMANY ONLY**

IPX4
EURO-PRO Operating LLC
180 Wells Avenue Suite 200
Newton, MA 02459
United States of America
1-800-798-7398
www.sharkninjamanuals.com
Technical Details
Model number: S3251***** 11
Input: 1550 Watts
Main unit voltage: 220-240V~, 50/60Hz
Euro-Pro and Shark are registered trademarks of
Euro-Pro Operating LLC.
Light & Easy is a trademark of Euro-Pro Operating LLC.
COPYRIGHT © EURO-PRO OPERATING LLC 2015
Illustrations may differ from actual product. We are
constantly striving to improve our products, therefore the
specifications contained herein are subject to change
without notice.
PRINTED IN CHINA
S3251_INTL_11_IB_150213_2