Sharp MX4111N User manual

20/04/2015
MX-4111N
MX-5111N
Technical Handy Guide
APRIL 2015
CONTENT
Product Specification
2
EEPROM Replacement Procedure
31
Product Options
4
HDD Replacement Procedure
32
Consumables
6
MX-EB12 Mirroring Kit
34
Initial Setup
8
SD Card Replacement Procedure
38
Colour Calibration
11
Firmware & Print Driver Revision
40
Updated
Maintenance
13
Test Simulation
41
Operating System Support
17
Trouble Codes
48
Electrical
18
Sensor Location
52
Coin Vend Interface
19
Jam Cause Codes
53
Firmware Upgrade
21
Repair Hints
56
Updated
Firmware Recovery
25
Technical Bulletin Index
63
Updated
E-Manual Update
27
Document Reference
67
Watermark Update
29
Notes
68

PRODUCT SPECIFICATION
SHARP
2
MX-4111N
MX-5111N
General Specification
Original paper size:
Max. A3
Printed Paper Size:
Tray : A3-A5R, Bypass : A3W-A5R
Standard Paper Capacity:
1,100 (500-sheet x 2, 100-sheet Multi bypass)
Maximum Paper Capacity:
5600 (500-sheet x 4, 100-sheet Multi bypass, 3500 LCC)
Paper Weight:
Tray : 60g/m2-220g/m2 Bypass : 55g/m2-256g/m2
Output Capacity:
400-sheet (centre: STD) Opt: MX-TRX2 100-sheet right tray
Warm-up Time:
30 sec
34 sec
Operation Panel:
10.1” Colour WSVGA
Resolution:
9,600 (equivalent) x 600 dpi (Copy),
9,600 (equivalent) x 600 dpi or 1200 x 1200 dpi (Printer)
Memory:
SD Card: 4 GB (Std), ICU:2 GB (Std.), Printer: 1 GB (Std), 1 GB (Opt)
HDD Capacity:
160GB
Duplex:
STD (60g/m2-220g/m2)
Dimensions (WDH):
643 x 761 x 966 mm
Weight:
126kg
127kg
Average Monthly Volume:
30-70K, Max 100K
40-80K, Max 150K
Environmental
Power Consumption:
Max. 1.84kW
TEC Value (Measured):
3.55 kWh
4.12 kWh
Noise (Measured):
Operating: 56db, (Max 70db), Waiting 45db
Emission (Actual):
Ozone: 0.2mg/h (B/W), 1.2mg/h (Col).
Dust: 0.5mg/h (B/W), 1.3mg/h (Col).
Styrene: 0.05mg/h (B/W), 0.09mg/h (Col).
Copier Specification
Copy Speed (Max.):
41ppm (A4), 19ppm (A3)
51ppm (A4), 23ppm (A3)
E-Sort / SOPM:
Yes / Yes (Colour and B/W)
First Copy Time (OC):
B/W: 4.7sec, Col 6.7sec
B/W: 4.1sec, Col 5.7sec
First Copy Time (DSPF):
B/W: 7.4sec, Col 10.3sec
B/W: 6.7sec, Col 9.2sec
Continuous Copy:
Max 999
Scan Resolution:
Colour: 600 x 600 dpi, B/W: 600 x 400 dpi (OC only)
600 x 400 dpi / 600 x 600 dpi
Zoom Range:
25 - 400% (DSPF 25 - 200%)
Tandem Copy:
STD
Document Filing
Capacity:
10GB (Quick Folder) + 76GB (Main/Custom Folder)
Quick Folder:
Max: 3,000 pages or 3,000 files
Main/Custom Folder:
Max: 20,000 pages or 3,000 files
User Registrations:
1000
Preview Thumbnails:
Supported
Document Feeder
Type:
STD. (DSPF)
Original capacity:
Max 150 sheets (80 g/m2)
Max Replacement Speed:
Copy Mode: 75opm (B/W), 51opm (Colour)
Image Send Mode: 75opm (B/W), 75opm (Colour)
Reference: opm (Original/Images per Minute)

SHARP
PRODUCT SPECIFICATION
3
MX-4111N
MX-5111N
Printer
Print Speed (Max.):
41ppm (A4), 19ppm (A3)
51ppm (A4), 23ppm (A3)
PDL (Emulation):
STD: PCL6, Opt: MX-PK11 (PS3), MX-PUX1 (XPS)
Interface:
USB2.0, 10Base-T / 100Base-TX / 1000BaseT
Supported OS:
Windows® XP* / Vista*, Windows® 7*, Windows® 8*, Windows® 8.1*
Windows® Server 2003* / 2008* / 2008R2 / 2012 (*32/64bit).
Mac OSX 10.2.8, 10.3.9, 10.4.11, 10.5.x, 10.6.x, 10.7.x, 10.8.x, 10.9.x,
10.10.x with MX-PK11.
XPS - Windows Vista only (Opt: MX-PUX1 & MX-ARSM10)
Bundled Utility Software
Status Monitor
USB Direct Print (Pull):
STD: JPEG, TIFF, PRN, PCL.
PDF, Encrypted PDF, PS Opt: PS3 (MX-PK11) is required.
XPS Opt:(MX-PUX1 & MX-ARSM10) are required
Tandem Print:
Yes (with MX2610/3110/3610/4111/5111N series only)
Pantone Colour (LUT):
Supported
Airprint Support:
Not Supported
Sharpdesk Mobile:
Supported (via Wireless Access Point or MX-EB13)
Opt: MXPK11 is required for full functionality.
Network Scanner
Requirement:
STD
Resolution:
100, 150, 200, 300, 400, 600 dpi
Format:
Mono: TIFF, PDF, Encrypted PDF & PDF/A
Colour: TIFF, JPEG, XPS, PDF, Encrypted PDF & PDF/A
Opt: MX-EB11 Compact PDF
Destination:
Desktop, FTP , Folder (SMB), USB memory, E-mail, HDD, I-Fax,
TWAIN / WIA compliant
User Registrations:
Max 500 (one touch), 500 (group)
Bundled Utility Software:
Network Scan Tool, Sharpdesk v3.3 (1 license)
Facsimile
Requirement:
Opt : MX-FX11
Communication Formula:
Super G3
Transmission Speed:
2sec.range(Super G3/JBIG) 6sec.range(G3/ECM)
Communication Line:
PSTN
Dial Registration:
Max 2000
Compression:
MH,MR,MMR,JBIG
Inbound Routing:
Yes (TIFF, XPS & PDF Format)
PC Fax:
Yes (For Windows only)
Output Finisher
Model:
Opt: MX-FNX9
Opt: MX-FN10
Opt: MX-FN11
Opt: MX-FN18
Type:
Inner Finisher
Saddle Finisher
4K Staple
Finisher
4K Saddle Finisher
Output Capacity:
500 sheets
1000 sheets
4000 sheets
4000 sheets
Functionality:
50 sheets
multi-staple
A4: 50sheets /
A3: 30sheets) ,
Off-set shifting,
Opt: Hole punch
(MX-PNX1)
50 sheets
multi-staple
A4 : 50sheets /
A3: 25sheets) ,
Off-set shifting,
Opt: Hole punch
(MX-PNX5)
50 sheets multi-
staple
A4 : 50 sheets /
A3 : 30 sheets) ,
Off-set shifting,
Opt: Hole punch,
(MX-PNX6)
50 sheets multi-
staple
A4 : 50 sheets /
A3 : 30 sheets) ,
Off-set shifting,
Opt: Hole punch,
(MX-PNX6)
Saddle Stitch Ability:
N/A
Max. 15 sheets
N/A
Max. 15 sheets

PRODUCT OPTIONS
SHARP
4
MX-PUX1
XPS Expansion
MX-PK11
PS3 Expansion
MX-FNX9
Inner Finisher
MX-PNX1
Hole Punch
MX-TRX2
Exit Tray Unit (R)
MX-FX11
Fax Expansion
MX-PF10
Barcode Font
MX-ARSM10
Expansion Memory
MX-FWX1
Internet Fax Kit
MX-EB11
PDF Compression Kit
MX-KB11(N)
External Keyboard
MX-FN10
Saddle Finisher
MX-PNX5
Hole Punch
MX-RB11
Paper Pass Unit
MX-FR33(U)
Data Security Kit
MX-LC11
3500 Sheet LCC (A4)
MX-AM10
Web Browsing Kit
MX-EB12(N)
Mirroring Kit (HDD)
MX-DE15
1 x 500 sheet Desk
MX-FN11
Finisher (4K)
MX-PNX6
Hole Punch
MX-FN18
Saddle Finisher (4K)
MX-PNX6
Hole Punch
MX-DE16
2 x 500 sheet Desk
MX-AMX1
Application Integration Module
MX-AMX2
Application Communication Module
MX-AMX3
External Account Module
MX-UN01A / UN05A
Sharp OSA-Network Scanner Tool (1 / 5 license kit)
MX-UN10A / UN50A
Sharp OSA-Network Scanner Tool (10 / 50 license kit)
MX-UNHA
Sharp OSA-Network Scanner Tool (100 license kit)

SHARP
PRODUCT OPTIONS
5
Machine Options
Model
Description
Comment
MX-DE15
Stand/500-sheet paper drawer
MX-DE16
Stand/500x2-sheet paper drawer
MX-LC11
3,500 sheets large capacity tray
MX-TRX2
Exit tray unit
MX-FNX9
Finisher
MX-PNX1
Punch module (A: 2, B: 3, C: 4, D: 4 wide)
Requires MX-FNX9
MX-RB11
Paper pass unit
MX-FN10
Saddle finisher
Requires MX-RB11
MX-PNX5
Punch module (A: 2, B: 3, C: 4, D: 4 wide)
Requires MX-FN10
MX-FN11
Finisher (4000 sheets)
MX-FN18
Saddle finisher (4000 sheets)
MX-PNX6
Punch module (A: 2, B: 3, C: 4, D: 4 wide)
Requires MX-FN11 or MX-FN18
MX-PK11
PS3 expansion kit
.
MX-PUX1
XPS expansion kit
MX-ARSM10 is required
MX-ARSM10
Expansion memory board
For MX-PUX1
MX-PF10
Barcode font kit
MX-FX11
Facsimile expansion kit
MX-FWX1
Internet-Fax expansion kit
AR-SU1
Stamp unit
MX-EB11
PDF high compression kit
MX-EB12
Mirroring kit
MX-EB12N
Mirroring kit N
MX-AM10
Web browsing kit
MX-KB11(N)
Keyboard unit N
MX-EB13
USB Wireless Adaptor
MX-AMX1
Application integration module
MX-AMX2
Application communication module
Cannot install with MX-FR33
MX-AMX3
External account module
MX-FR33
Data security kit (CC version)
MX-FR33U
Data security kit (Commercial version)
MX-USX1
Sharpdesk Additional license kit (1 license)
MX-USX5
Sharpdesk Additional license kit (5 licenses)
MX-US10
Sharpdesk Additional license kit (10 licenses)
MX-US50
Sharpdesk Additional license kit (50 licenses)
MX-USA0
Sharpdesk Additional license kit (100 licenses)
MX-UN01A/05A
Sharp OSA-Network Scanner Tool (1/5 license)
MX-AMX2 is required.
(MXPK11 is also required
for Direct PDF Print).
MX-UN10A/50A
Sharp OSA-Network Scanner Tool (10/50 licenses)
MX-UN1HA
Sharp OSA-Network Scanner Tool (100 licenses)

CONSUMABLES
SHARP
6
CONSUMABLES
MX-4111N, MX-5111N
Product Code
Description / Contents
Approx. Life
MX-51GTBA
Black Toner Cartridge
(A4 @ 5%)
40k
MX-51GTCA
Cyan Toner Cartridge
(A4 @ 5%)
18k
MX-51GTMA
Magenta Toner Cartridge
(A4 @ 5%)
MX-51GTYA
Yellow Toner Cartridge
(A4 @ 5%)
PROCESS UNIT:
MX-51GVBA
Black Developer
150k
MX-51GVSA
Colour Developer Kit (CMY)
100k
MX-51GUSA
Drum Unit (Complete):-
150k (Mono)
100k (Colour)
MX-31GRSA
OPC Drum
MX-510MK
Main Charge Kit:-
Main charge unit
Cleaning blade AR
Cleaning gum AS
MX-510CU
PTC Kit:-
PTC unit.
300k
MX-510HB
Waste Toner Collector:-
Includes LSU cleaner x 3
50k (approx.)
MX-C31FL
Ozone Filter Kit:-
Ozone filter.
150k
MX-310PD
Paper Dust Removing Kit:-
Paper dust removal unit.
150k
FUSING UNIT:
MX-361FB
MX-510FB*
Fusing Belt Kit:-
Fusing belt.
Meandering Suppress collar x 2.
200k
MX-510LH
Pressure Roller Kit:-
Fusing roller.
Pressure roller.
200k
MX-510WB
Web Cleaning Kit:-
Web roller.
Web guide shaft x 2.
Web pressure roller.
Web pressure roller bearing x 2
200k
TRANSFER SECTION:
MX-510B1
Primary Transfer Belt Kit:-
Primary transfer belt AR.
300K
MX-510TL
Primary Transfer Blade Kit:-
Primary transfer blade AR.
300K
MX-310B2
Secondary Transfer Belt Kit:-
Secondary transfer belt D3.
300K
*MX-510FB has been discontinued

SHARP
CONSUMABLES
7
CONSUMABLES:
MX-4111N, MX-5111N
Product Code
Description / Contents
Approx. Life
MX-SCX1
Staple Cartridge (for MX-FNX9 & MX-FN10)
5000 staples (x 3)
AR-SC2
Staple Cartridge (for MX-FN11 & MX-FN18)
5000 staples (x 3)
AR-SC3
Saddle Staple Cartridge (for MX-FN10 & MX-FN18)
2000 staples (x 3)
AR-SV1
Stamp Cartridge (for AR-SU1)
2 cartridges
SERVICE ROTATION:
MX-510U1
Primary Transfer Belt Unit
For Service Rotation
MX-410U2
Secondary Transfer Belt Unit
MX-411FU
Fusing Unit (230v) for MX-4111N only
MX-510FU
Fusing Unit (230v) for MX-5111N only
Note:
The consumable life may vary, depending on the document density, temperature, humidity and machine
operation.

INITIAL SETUP
SHARP
8
DEVELOPER SET-UP
Sim 25-02 Auto Developer Adjustment - Select CMYK.
Toner Installation must be performed after Auto Developer Adjustment is
completed.
**For optimum image quality & performance, it is recommended to setup &
install developer at the customer site.
Clean LSU Dust Proof Glass.
TONER INSTALLATION & REPLENISHMENT
Install CMYK Toner Cartridges.
Caution:
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation Mode
during Initial Toner Replenishment.
PRODUCT ACTIVATION & FIRMWARE UPGRADE
Activation of Optional Product(s):- System Settings –Product Key.
Sim 22-05 Check Firmware version(s):- Upgrade to latest version.
INITIAL SETUP
Sim 26-01 Right Tray Installation:- Yes/No.
Sim 26-02 LCC Installation (Paper Size):- A4.
Sim 26-06 Machine Destination.
Sim 26-35 Set Multi Error Counter:- Set to 1 (Multi Count).
Sim 26-50 Long Paper Support (up to 1200mm):- 0 = Disable, 1 = Enable.
Sim 26-52 Non Printed Paper Counter Set-up.
Sim 55-03 Process Mixed Size Pages (orientation) when Printing in Duplex:-
SSW 3-6, 0 = Disable, 1 = Enable.
Sim 55-03 Toner Remain Status Display: SSW 22-5, 0 = Disable, 1 = Enable.
System Settings: Adjust Date/Time (Inc. Daylight Saving setting).
Keyboard Language Setting (For Embedded & Optional Keyboards):-
System Settings –Default Settings –Keyboard Select: Set English(US)
Network Settings –Print Port Settings: Disable WSD.
Set cassette size by adjusting the guides in the cassette.
Paper Size & Type Setting:- System Settings –Paper Tray Settings.

SHARP
INITIAL SETUP
9
PRINT IMAGE POSITION & MAGNIFICATION
Automatic Adjustment:-
Sim 50-28 BK MAG ADJ (Main Scan Mag).
SETUP/PRINT ADJ (Lead, Offset or All).
Manual Adjustment:-
Sim 50-10 BK MAG (inside dimension) to 240mm.
Sim 50-10 Image Off Centre Adjustment.
Sim 50-05 Printer Lead Edge & Void Adjust.
IMAGE SKEW & COLOUR REGISTRATION
Sim 61-04 Image Skew Adjustment (Black):- Select A3 Paper
Sim 50-22 Colour Registration/Skew & OPC Drum Phase Adjustment:-
Check/Adjust SKEW (CMY) so value is Close to 0 as possible
(Result=OK)
COLOUR CALIBRATION
Sim 46-74 Engine & Printer Colour Calibration:- Select FACTORY Mode.
COPY IMAGE QUALITY
Check Image Quality (Copy Mode) –Density, Magnification, Lead Edge & Void.
If NG, perform the following adjustments as required:-
Sim 46-01 Copy Density Adjust. (Colour).
Sim 46-02 Copy Density Adjust. (B/W).
Sim 46-09 DSPF Copy Density Adjust.
Sim 50-28 OC ADJUST (Lead, Offset & Mag).
SPF ADJ:(Lead, Offset & Sub scan).
Manual Adjustment (Magnification, Lead Edge, Void, Off Centre etc):-
Sim 48-01 Magnification Adjustment (OC & SPF).
Sim 50-01 Lead/Rear Edge, Loss & Void Adjust.
Sim 50-12 OC & SPF Off Centre Adjust.
PRINT IMAGE QUALITY
Check Image Quality (Print Mode) –Density.
Sim 64-05 PCL Density Test Page.
Sim 64-06 PS Density Test Page [MX-PK11 only].

INITIAL SETUP
SHARP
10
PERIPHERAL / OPTION CONFIGURATION
FAX OPTION –MX-FX11
Sim 66-02 Fax SW Setting (Destination).
Sim 66-10 Fax Memory Clear (For Extended Memory).
Sim 66-39 Fax Destination Set.
SADDLE FINISHER –MX-FN10, MX-FN18
Sim 03-10 Saddle Fold/Staple Position Adjustment.
Sim 26-65 Finisher Alarm Mode:-
Limit number of Copies in staple mode (ON/OFF).
ACRE –SCAN COMPRESSION KIT MX-EB11
Sim 22-05 Check ACRE firmware version - must be 02.00.A1 (or higher):-
Upgrade to latest version using Sim 49-01.
EXTERNAL ACCOUNTING MODULE –MX-AMX3
Sim 55-03 Auto clear function before Copy job execution:-
SSW 1-5 0 = Disable, 1 = Enable.
Sim 55-03 USB Card Reader detection control:-
SSW 6-8 0 = Disable, 1 = Enable.
Sim 55-03 Continuous print mode (job queuing for OSA):-
SSW 24-7 0 = Disable, 1 = Enable.
MFP DATA BACKUP
Sim 22-06 Data Simulation Print.
Device Clone & Storage Backup.
Sim 56-01 Backup EEPROM Data to HDD.

SHARP
COLOUR CALIBRATION
11
Automatic Colour Calibration - FACTORY MODE
Note: When adjusting colour balance before or after routine maintenance, always use the
recommended paper (Mondi 90gsm or equivalent) for optimum image quality.
DEFAULT COLOUR BALANCE SETTING:
Sim 63-11 [for Engine]
Sim 67-26 [for Printer]
Def 1 Standard Colour Balance setting (Default).
Def 2 Colour balance with slightly strong cyan.
Def 3 Colour balance with the emphasis on Cyan.
COLOUR BALANCE ADJUSTMENT:
Sim 46-74 [Engine & Printer]
FACTORY MODE
Place printed test pattern onto glass for both Copy &
Printer modes.
Manual Colour Calibration –SERVICE MODE
HIGH DENSITY PROCESS CONTROL:
[Execute]
Sim 44-06
COLOUR BALANCE ADJUSTMENT:
Sim 46-74 [Engine & Printer]
SERVICE MODE
Place printed test pattern onto glass for both Copy &
Printer modes.
MANUAL COLOUR DENSITY ADJUSTMENT:
Sim 46-21 [for Engine]
Sim 67-25 [for Printer]
Adjust CMYK (17 points) for Copy & Printer Modes.

COLOUR CALIBRATION
SHARP
12
PRINTER DENSITY CHECK:
Sim 64-05 [PCL Printer]
Sim 64-06 [PS Printer]
SERVICE COLOUR TARGET SETTING:
Sim 63-07 [for Engine]
Sim 67-27 [for Printer]
Scan Test Pattern to Register Custom Service Target
DEFAULT SETTING (Service Mode):
To return machine to “Standard” setting:-
STANDARD SERVICE TARGET SETTING:
[Execute]
Sim 63-08 [for Engine]
Sim 67-28 [for Printer]
COLOUR BALANCE ADJUSTMENT:
Sim 46-74 [Engine & Printer]
SERVICE MODE
Place printed test pattern onto glass for both Copy &
Printer modes.

SHARP
MAINTENANCE
13
Maintenance Indications:
DK
Black Drum (Counter) has reached
the specified life.
Replace Black Drum
Process
Section
(Drum)
DC
Cyan Drum (Counter) has reached
the specified life.
Replace Cyan Drum
DM
Magenta Drum (Counter) has reached
the specified life.
Replace Magenta Drum.
DY
Yellow Drum (Counter) has reached
the specified life.
Replace Yellow Drum.
VK
Black Developer (Counter) has reached
the specified life.
Replace Black Developer.
Process
Section
(Developer)
VC
Cyan Developer (Counter) has reached
the specified life.
Replace Colour
Developer Kit.
VM
Magenta Developer (Counter) has reached
the specified life.
VY
Yellow Developer (Counter) has reached
the specified life.
FK1
Fusing Belt Print Counter has reached the
specified limit.
Replace the Fusing
Belt Kit.
Fuser
Section
FK2
Fuser Pressure Roller Print Counter has
reached the specified limit.
Replace the Pressure
Roller Kit.
FK3
Fuser Web Cleaner (Counter) has reached
the specified limit
(Pop Up FK3 Error –Web End Detected)
Replace the
Web Cleaning Kit
TK1
Primary Transfer Unit Counter has reached
the specified limit.
Replace Primary Transfer
Belt and Blade kits.
Transfer
Section
TK2
Secondary Transfer Unit Counter has
reached the specified limit.
Replace the Secondary
Transfer Belt Kit.
TA
Maintenance [All] Counter has reached specified limit
CA
Maintenance [Colour] Counter has reached specified limit
AA
Maintenance [All] & [Colour] Counters have reached the specified limits
Starting Powder:
The following starting powder should be applied to the relevant consumable item during maintenance:-
Starting Powder
OPC Drum
Primary Transfer Belt
MX-4111N
MX-5111N
UKOG-0312FCZZ
[Stearic Acid]
CKOG-0345DS51 *
[Yellow Toner]
Note*: Kynar Powder [UKOG-0123FCZZ] can also be applied to the Primary Transfer Belt.
CAUTION:
Do not apply Stearic Acid (UKOG-0312FCZZ), Strontium Titanium (UKOG-0316FCZZ) or Titanium
Hydroxide (UKOG-0322FCZZ) starting powder to the Primary Transfer Belt.

MAINTENANCE
SHARP
14
Replacement Schedule:
K
CMY
Description
Process Section - Cyan, Magenta & Yellow:
(or when the colour maintenance counter has reached the specified life).
x
Replace Cyan, Magenta & Yellow Drum Units (MX-51GUSA x 3) or
OPC Drum (MX-51GRSA x 3) &
Main Charge Unit (MX-510MK x 3)
x
Replace C, M, Y Developer (MX-51GVSA).
x
Sim 24-04 Clear C, M, Y (Colour) Drum CTRG Counters.
x
Clear C, M, Y (Colour) Main Charger Counters.
x
Clear C, M, Y (Colour) Drum Blade Counters.
x
Clear Maintenance [Colour] Counter.
x
Sim 25-02 Toner Concentration Auto Adjustment - Select C, M, Y.
Notes:
If ALL developer is replaced at the same time, select CMYK.
When Sim 25-02 is executed, the Developer Counter (Sim 24-05) is
also cleared automatically.
x
Caution: Ensure ALL toner cartridges are removed, prior to executing Sim 25-02.
x
Sim 44-27 Clear Half Tone Process Correction.
Process Section -Black:
(or when the Black maintenance counter has reached the specified life).
x
Replace Black Developer (MX-51GVBA).
x
Replace Black Drum Unit (MX-51GUSA) or
OPC Drum (MX-51GRSA).
Main Charge Unit (MX-510MK).
x
Sim 24-05 Clear K (Black) Developer Counter.
x
Sim 24-04 Clear K (Black) Drum CTRG Counter.
x
Clear K (Black) Main Charger Counter.
x
Clear K (Black) Drum Blade Counter.
x
Clear Maintenance [ALL] Counter.
x
Sim 25-02 Toner Concentration Auto Adjustment - Select K.
Notes:
If ALL developer is replaced at the same time, select CMYK.
When Sim 25-02 is executed, the Developer Counter (Sim 24-05) is
also cleared automatically.
x
Caution: Ensure ALL toner cartridges are removed, prior to executing Sim 25-02.
Image Quality Adjustments (for CMYK):
Sim 44-02 Image Density & Registration Sensor Adjustment.
Sim 50-22 Drum Position & Registration Adjustment - select ALL.
Sim 44-06 Process Control execution.
Sim 46-74 Automatic Colour Balance Adjustment (Copy & Printer).
Sim 46-01 Adjust Copy Exposure Density (Colour).
Sim 46-02 Adjust Copy Exposure Density (B/W).

SHARP
MAINTENANCE
15
Description
150K
Maintenance Schedule A:
Process Section:
In addition to Black Consumable schedule (and/or colour schedule if indicated):-
Check Waste Toner Container (MX-510HB).
Replace Ozone Filter Kit (MX-C31FL).
Sim 24-04 Clear Ozone Filter Counter.
Paper Feed & Transport:
Replace Paper Dust Removal Unit (MX-310PD).
Check/Clean all Paper Path Sensors (including Duplex unit).
Check/Clean/Replace PF Rollers (check tray counter using Sim 22-09).
Sim 24-04 Clear PS Paper Counter.
General:
Clean all optics, CCD, and white reference plate.
Clean all DSPF sensors.
200K
Maintenance Schedule B:
Fuser Section:
Replace Fusing Belt Kit (MX-361FB or MX-510FB)
Replace Fusing Pressure Roller Kit (MX-510LH).
Replace Web Cleaning Kit (MX-510WB).
Check & Clean Upper and Lower Thermistors.
Check & Clean Fuser Separator Pawls.
Sim 24-04 Clear Fusing Belt Counter.
Clear Separation Clean Roller.
Clear Fusing Belt Counter.
Clear Fusing Roller Counter.
Clear Press Roller Counter.
Clear Fusing Web Counter.
Perform the following, only when replacing the following fuser parts available
via service parts:-
Replace Fusing Separation Pawl Lower [PTME-0313FCZZ x4]
Sim 24-04 Clear Separate Pawl Counter.
Replace Fuser Separation Plate Upper [CPLTM8010FC03]
Sim 24-04 Clear Separate Plate Counter.
300K
Maintenance Schedule C:
In addition to Maintenance Schedule A and Maintenance Schedule B every 600k
only, perform the following:-
Process Section:
Replace PTC unit (MX-230CU).
Sim 24-04 Clear PTC Counter.

MAINTENANCE
SHARP
16
300K
Maintenance Schedule C: (Cont’d)
Transfer Section:
Replace Primary (Image) Transfer Belt Kit (MX-510B1).
Replace Primary Transfer Cleaning Blade Kit (MX-510TL).
Replace Secondary Transfer Belt Kit (MX-310B2).
Clean ID & Registration Sensors.
Sim 24-04 Clear TC1 Belt Counter.
Clear Trans Blade Counter.
Clear TC2 Belt Counter.
Sim 50-22 Drum Position & Registration Adjustment - select ALL.

SHARP
OPERATING SYSTEM SUPPORT
17
MX-4111N, MX-5111N
MX-4111N
MX-5111N
Windows Client
Windows Server
Apple OSX
8.1
8
7, Vista
2008
2008R2
2012
2012R2
10.8
10.9
10.10
32/64
32/64
32/64
32/64
64
64
64
Sharp Advanced
Printer Language




PCL5
PCL6

WHQL

WHQL

WHQL

WHQL

WHQL

WHQL

WHQL
PS
*1
WHQL
*1
WHQL
*1
WHQL
*1
WHQL
*1
WHQL
*1
WHQL
*1
WHQL
PPD
*1
WHQL
*1
WHQL
*1
WHQL
*1
WHQL
*1
WHQL
*1
WHQL
*1
WHQL
*1
*1
GPD (PCL)
XPS

*V
WHQL

PC-Fax
*2
*2
*2
*2
*2
*2
*2
Sharpdesk v3.3
Composer




SAP
Use SH1DN050 (PCL) or SH1HN050 (PS *1) Device Type
Airprint (Native)
Button Manager
Twain Scan
[Network]

WHQL

WHQL

WHQL

WHQL

WHQL

WHQL

WHQL
Scan to
Sharpdesk v3.3




Scan to Folder







*3
*3
Scan to FTP









Sharp OSA
Network Scan Tool
*4
*4
*4
*4
*4
*4
*4
SRDM







Notes:
*1 MX-PK11 is required.
*2 MX-FX11 is required.
*3 Supported on Mac OSX 10.4 to 10.8 therefore, operation is not guaranteed.
*4 MX-AMX2 is required –Client is not supported on Windows Server OS.
*V XPS Driver is only supported on Windows Vista (32/64bit) - MX-PUX1 & MX-ARSM10 required.

ELECTRICAL
SHARP
18
High Voltage Settings
Note: The adjustment value of each colour mode is specified on the information label attached to the
MC/DV High Voltage Power PWB.
Using Simulation 8-01 (DV Bias Setting) & Sim 8-02 (MC Grid Bias Setting), enter the values
specified, especially after replacing the PCU PWB, EEPROM or following U2 trouble.
DV BIAS VOLTAGE –SIMULATION 08-01
Item
Mode
Adjustment
Range
Actual Voltage
MX-4111N
MX-5111N
Middle Speed
DV Bias Voltage
K
0-600
-450 +/- 5V
C
M
Y
Low Speed
DV Bias Voltage
K
-450 +/- 5V
C
-430 +/- 5V
M
-430 +/- 5V
Y
-430 +/- 5V
MAIN CHARGE GRID VOLTAGE –SIMULATION 08-02
Item
Mode
Adjustment
Range
Actual Voltage
MX-4111N
MX-5111N
Middle Speed
MC Grid Voltage
K
150-850
-630V +/- 5V
-640V +/- 5V
C
M
Y
Low Speed
MC Grid Voltage
K
-620V +/- 5V
-620V +/- 5V
C
-600V +/- 5V
-600V +/- 5V
M
-600V +/- 5V
-600V +/- 5V
Y
-600V +/- 5V
-600V +/- 5V

SHARP
COIN VEND INTERFACE
19
All MX series machines have a coin vend interface located on the PCU Main PWB. The vending device
activates various signals to indicate paper sizes and operation.
Connector Manufacture: JST (www.jst.com)
Connector Type PND series
Connector Part Code (Wire Side) PNDP-16V-Z
Before connecting a third party auditor, the device should confirm to the following:-
1. The auditor interface should be optically isolated from the copier.
2. The device should be Power Supply Unit independent.
3. The device power supply unit should be a plug top adapter, not internal.
4. The plug top adapter should have a reinforced insulation barrier.
5. The audit device MUST comply and display the relevant safety approval mark (C-Tick, CE
or equivalent).
To enable coin vend function, test simulation 26 –03 should be set as required:-
Coin Vendor Mode
Diagnostic
Setting
The specified
quantity is
completed.
Remainder of money
is left
Insufficient money during copy job
The specified
quantity is
completed.
No money
remaining
Black/Colour
(No money
remaining)
Colour
(Remainder of
money left)
Condition 1
Condition 2
Condition 3
Condition 4
MODE 1
Operation 1
Operation 2
Operation 2
Operation 1
MODE 2
Operation 1
Operation 1
Operation 2
Operation 1
MODE 3
Operation 1
Operation 3
Operation 2
Operation 3
OPERATION 1 Wait for auto clear setting time
(Default 60sec –can be changed by the system setting)
OPERATION 2 Auto clear is not made.
OPERATION 3 Setting is immediately cleared.
Cont’d

COIN VEND INTERFACE
SHARP
20
Connector Signals
Pin No.
PCU PWB (CN23)
1
+ 24v
Out
2
GND
Out
3
CV_B/W_COPY
In
4
CV_COUNT
Out
5
CV_START
Out
6
CV_CA
Out
7
CV_COLOUR_ COPY
In
8
CV_COLOUR1
Out
9
CV_STAPLE
Out
10
CV_COLOUR0
Out
11
CV_DUPLEX
Out
12
5v
Out
13
CV_SIZE0
Out
14
CV_SIZE1
Out
15
CV_SIZE2
Out
16
CV_SIZE3
Out
Colour Signals
Colour Mode
(CL-COLOR1)
(CL-COLOR0)
B/W
0
0
Full Colour
1
1
Others
(Single/Two Colour)
0
1
Paper Size Signals
SIZE3
SIZE2
SIZE1
SIZE0
PAPER SIZE
0
0
0
0
NIL
0
0
0
1
A3
1
0
1
1
A3W
0
0
1
0
A4
0
0
1
1
LT
0
1
0
0
B4
0
1
0
1
LG
0
1
1
0
WLT
0
1
1
1
INV
1
0
0
0
B5
1
0
1
0
A5
1
0
0
1
EXTRA