Sharp AR-PE2 User manual

CONTENTS
SHARP CORPORATION This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SERVICE MANUAL
CODE: 00ZARPX3//A1E
PRINTER I/F KIT
AR-PE2
AR-PX3
MODEL AR-PX4
[1] OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[2] SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
PARTS GUIDE

– 1 –
[1] OUTLINE
This unit is used to connect the printer controller with the scanner and
the printer section in the AR-C160.
1. Unit composition
This unit is composed of the following major parts:
AR-PE2
• Controller
• I/F card
• Connection cable
AR-PX3/PX4
• Power supply unit
2. Outline of operations
(Printer mode)
Each color image data of 8bit of Y/M/C/K outputted from the print con-
troller.
(Scanner mode)
Each color image data of R/G/B scanned by the scanner is inputted to
the printer I/F card.
(Circuit system)
High-speed data transmission/reception is performed between the en-
gine and the print controller.
[2] SETUP
Necessary tools: Screwdriver
1. Unpacking
(Parts list)
AR-PE2
AR-PX3/PX4
2. Parts assembly
1) Remove the operation unit.
Left side Right side
2) Remove the left and right upper cabinet.
3) Remove the ICU PWB shield plate.
4) Remove the CCD flat cable connector.
No. Part name Quantity
1 Controller 1
2 I/F card 1
3 Flat cable 1
4 Wake up harness 1
No. Part name Quantity
1 Power supply unit 1
2 Screw (M4) 8
3 Caution label (Only EU) 1
FOR USE WITH COMPATIBLE SHARP COPIERS.
SEE SHARP COPIER INSTALLATION MANUAL TO DETERMINE SUITABILITY.
AR-PE2/PX3/PX4 Installation Manual

– 2 –
5) Open the scanner (reading) unit and fix it with the hold shaft.
6) Remove the interface cabinet.
7) Remove the cover plate on rear cabinet.
Removed screw is used for attach the printer I/F card.
8) Connect engine side I/F cable.
9) Attach the printer I/F card with the accessory screw, and connect
the wake up signal harness and clock harness.
10) Attach the printer power supply unit, and connect printer PS cable.
Wake up signal harness
Clock harness

– 3 –
11) Remove the top cover of the printer controller and attach the
printer controller.
12) Connect controller side I/F cable and DC cable.
13) Attach the top cover of the printer controller.
14) Install all the parts that were removed to their original positions.
15) Attach the caution label to the cabinet. (Only EU version)
3. Setting
1) Turn on the power of the unit.
2) Enter the simulation 26-1 mode.
3) Press "PRN: AR-PE2" button. (Communication between the unit
and the printer controller is allowed.)
4) Cancel the simulation mode.

PARTS GUIDE
1電源ﾕﾆｯﾄ (Power supply unit)
NO. PARTS CODE JAPAN ONLY
ORDER CODE
PRICE RANK NEW
MARK
PART
RANK DESCRIPTION
Ex. Ja.
1
XBPSD30P16000 541 970 1103 AA DD C Screw (3×16) ﾋﾞｽ
2
! RDENC0009FCZZ 578 685 0519 BL HL N E Power supply PWB (100V Series) 電源基板
! RDENC0010FCZZ 578 685 0520 BS MJ N E Power supply PWB (200V Series) 電源基板
3
DHAI-3325FC11 572 542 2055 AN EG N C PRT power supply harness PRT 電源ﾊｰﾈｽ
4
DHAI-3321FC11 572 542 2054 AM EG N C DC harness DC ﾊｰﾈｽ
5
PSPAZ0382FCZZ 572 413 0295 AA DD C Spacer for BCL (100V Series) BCL ﾖｳｽﾍﾟｰｻｰ
6
XBPSD30P08K00 541 970 0014 AA DD C Screw (3×8S) ﾋﾞｽ
7
LBNDJ0013FCZ1 572 201 0118 AA DJ C Band ﾊﾞﾝﾄﾞ
8
LSUPP0109FCZZ 572 233 0127 AC DJ C Spacer ｽﾍﾟｰｻｰ
9
LPLTM5950FCZZ 578 221 0686 AN EG N C PRT power supply fixing plate PRT 電源押えﾌﾟﾚｰﾄ
10
CPWBN1512FC51 572 684 3841 BK HC N E PRT power supply relay PWB (100V Series) PRT ﾃﾞﾝｹﾞﾝﾘﾚｰ基板
CPWBN1512FC52 572 684 3842 BL HG N E PRT power supply relay PWB (200V Series) PRT ﾃﾞﾝｹﾞﾝﾘﾚｰ基板
11
LSUPP0086FCZZ 572 233 0116 AB DJ C Supporter (LCBS-6) ｻﾎﾟｰﾀｰ
1電源ﾕﾆｯﾄ (Power supply unit)
2梱包 &付属品 (Packing Material & Accessories)
NO. PARTS CODE JAPAN ONLY
ORDER CODE
PRICE RANK NEW
MARK
PART
RANK DESCRIPTION
Ex. Ja.
1
SPAKA6200FCZZ 578 902 0308 AE DS N D Spacer B ｽﾍﾟｰｻｰ B
2
SPAKA399ACCZZ 505 902 5004 AB DD D Vinyl bag ﾎﾟﾘ袋
3
SSAKA0006UCZZ 541 906 1016 AA DD D Vinyl bag (50×60) ﾎﾟﾘ袋
4
XHBSD40P08000 578 970 0074 AA DD C Screw (4×8) ﾋﾞｽ
5
XBBSE40P10000 572 970 0641 AA DD C Screw (4×10) ﾋﾞｽ
6
TLABZ4173FCZZ 572 917 3365 AG DX D Caution label (Europe,U.kingdom,Australia,Newzealand) 注意ﾗﾍﾞﾙ
7
SPAKA6199FCZZ 578 902 0307 AL EB N D Spacer A ｽﾍﾟｰｻｰ A
8
SPAKC6198FCZZ 578 901 0544 AM EG N D Packing case (JAPAN) ﾊﾟｯｷﾝｸﾞｹｰｽ
SPAKC6198FC11 578 901 0545 AM EG N D Packing case (U.S.A/CANADA) ﾊﾟｯｷﾝｸﾞｹｰｽ
SPAKC6198FC12 578 901 0546 AM EG N D Packing case (Other countries) ﾊﾟｯｷﾝｸﾞｹｰｽ
2梱包 &付属品 (Packing Material & Accessories)
8
F
F
F
8
9
10
11
12
1
2
3
4
5
6
7
11
FCP04931
A
A
B
B
B
C
CC
A
D
D
D
E
E
E
10
2
6
6
200V Series
2
8
FCP04932
1
4
5
3
67

All rights reserved.
Printed.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic; mechanical; photocopying; recording or otherwise
without prior written permission of the publisher.
Trademark Acknowledgments
Microsoft Windows, MS-DOS, Windows NT, Windows 2000 are trademarks of Microsoft
Corporation in the U.S.A.and other countries.
Macintosh, Power Macintosh, Mac OS, LaserWriter, and AppleTalk are registered trademarks of
Apple Computer, Inc.
IBM, PC/ AT, and PowerPC are trademarks of International Business Machines Corporation.
Pentium is a registered trademark of Intel Corporation.
PCL is a trademark of the Hewlett- Packard Company.
PostScriptis a registered trademark of Adobe Systems Incorporated.
NetWare is a registered trademark of Novell, Inc.
All other trademarks and copyrights are the property of their respective owners.
Digital Document Systems Group
Quality & Reliability Control Center
Yamatokoriyama, Nara 639-1186, Japan
2001 June Printed