Shure UHF-R Wireless User manual

Model UHF-R®Wireless Systems
User Guide
©2013 Shure Incorporated
27A20021 (Rev. 3)
Printed in U.S.A.
Model UHF-R®Wireless Systems
모델 UHF-R® Wireless 사용자 안내서
モデル UHF-R® ワイヤレス 取扱説明書
Panduan untuk Pengguna Wireless Model UHF-R®
UHF-R® 无线系统 型号用户指南
N108

3
English
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila-
tion and install in accordance with the manufacturer’s instructions.
8. DO NOT install near any heat sources such as open flames, radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open
flame sources on the product.
9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wider blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replace-
ment of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve-
nience receptacles, and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified by the manu-
facturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long
periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required when the ap-
paratus has been damaged in any way, such as power supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with
liquids, such as vases, on the apparatus.
16. The MAINS plug or an appliance coupler shall remain readily operable.
17. The airborne noise of the Apparatus does not exceed 70dB (A).
18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a
protective earthing connection.
19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture.
20. Do not attempt to modify this product. Doing so could result in personal injury and/or
product failure.
21. Operate this product within its specified operating temperature range.
This symbol indicates that dangerous voltage constituting a risk of
electric shock is present within this unit.
This symbol indicates that there are important operating and mainte-
nance instructions in the literature accompanying this unit.
WARNING: This product contains a chemical known to the State of California to cause cancer and birth
defects or other reproductive harm.
WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualied service personnel. The
safety certications do not apply when the operating voltage is changed from the factory setting.
重要安全事项!
1. 必须阅读这些注意事项。
2. 必须保留这些注意事项。
3. 必须注意所有警告内容。
4. 必须遵循所有注意事项。
5. 不要在靠近水的地方使用本设备。
6. 只能用干布擦拭设备。
7. 不要堵塞任何通风口。留出足够的距离，确保充分通风，并安装在符合制造
商要求的位置。
8. 不要将本设备安装在任何热源（如明火、散热器、调温器、火炉或包括功率
放大器在可的其它可能产生热量的装置附近。不要将任何明火火源放置在产
品上。
9. 不要破坏带极性或接地类型插头的安全功能。极性插头带有两个插片，其中一
个比另一个宽。接地类型插头带有两个插片和第三个接地插脚。较宽的插片或
第三个插脚是为安全目的设置的。如果提供的插头无法插入您的插座，请向电
工咨询如何更换合适的插座。
10. 保护电源线防止被脚踩踏或被夹紧，尤其是在插头、方便插座和机身电源线
的引出处。
11. 只能使用制造商指定的连接部件/附件。
12. 只能使用制造商指定的或随设备售出的手推车、支座、三角架、托
架或支撑台。如果使用手推车，在移动装有设备的手推车时应注意
安全，避免设备翻落。
13. 在雷电天气或长时间不使用情况下，应拔下设备插头。
14. 所有维修均应由合格的维修人员执行。如果设备因下列情况损坏，应进行维
修：电源线或插头损坏、液体泼溅到设备上或异物进入设备，设备暴露在雨水
或潮湿环境中而无法正常工作，或摔落到地上。
15. 不要将本设备暴露在可能滴水和溅水的地方。不要将装有液体的容器（如花瓶
等）放在本设备顶部。
16. 电源插头或电器转接头应保持在随时可用的状态。
17. 本装置的空气噪声不超过 70dB (A)。
18. 应将符合 I 类标准的设备连接到带有接地保护装置的主电源插座。
19. 为降低起火或电击危险，不要将本设备暴露在雨中或潮湿环境下。
20. 不要尝试改装本产品。否则可能会导致人身伤害和/或产品故障。
21. 应在技术规格指定的温度范围内操作此产品。
这个符号表示本设备中存在可能导致触电的危险电压。
这个符号表示本设备附带的说明书中具有重要的操作和维护
说明。

Shure UHF-R Wireless
4
중요 안전 지침
1. 이 지침을 정독해 주십시오.
2. 이 지침을 잘 보관해 주십시오.
3. 모든 경고에 유의하십시오.
4. 모든 지침을 준수하십시오.
5. 이 기기를 물 가까이에 두고 사용하지 마십시오.
6. 마른 수건으로만 닦으십시오.
7. 통풍구를 막지 마십시오. 적합한 환기를 위해 충분히 거리를 두고 제조업체의 안내
서에 따라 설치하십시오.
8. 개방된 화염, 난방기, 방열 조절기, 스토브, 기타 열을 발산하는 기기 (앰프포함) 등
의 열원 근처에 설치하지 마십시오. 제품 위에 개방된 화염원을 올려 놓지 마십시오.
9. 안전을 위해 유극 또는 접지 타입의 플러그를 반드시 사용하십시오. 유극 유형의 플
러그는 넓은 핀과 좁은 핀, 두 개의 핀으로 구성되어 있습니다. 접지형 플러그에는
두 개의 핀과 하나의 접지 단자가 있습니다. 넓은 핀이나 접지 단자는 사용자의 안전
을 위한 것입니다. 제공된 플러그가 콘센트에 맞지 않으면 전기 기사에게 문의하여
콘센트를 교체하십시오.
10. 전원 코드는 밟히지 않도록 주의하고 특히 전원 플러그 사이, 접속 소켓 및 기기에서
나오는 부분에 전원 코드가 끼이지 않도록 보호하십시오.
11. 제조업체가 지정한 부속품/액세서리만 사용하십시오.
12. 제조업체에서 지정하거나 기기와 함께 판매되는 카트, 스탠드, 받침대, 브
라켓 또는 테이블에서만 사용하십시오. 카트를 사용하는 경우, 이동 시 카
트와 기기가 넘어져 부상을 입지 않도록 주의하십시오.
13. 낙뢰시 또는 장기간 사용하지 않을 때는 기기의 전원을 빼놓으십시오.
14. 모든 서비스는 자격을 갖춘 서비스 전문가에게 의뢰하십시오. 전원 코드나 플러그
가 손상된 경우, 기기 안으로 액체가 들어가거나 물건을 떨어뜨린 경우, 기기가 비나
물에 젖은 경우, 기기가 정상적으로 작동하지 않는 경우 또는 기기를 떨어뜨린 경우
와 같이 기기가 손상되었을 때는 서비스를 받아야 합니다.
15. 기기에 물을 떨어뜨리거나 뿌리지 마십시오. 화병과 같이 물이 담긴 물체를 기기 위
에 올려놓지 마십시오.
16. MAINS 플러그나 기기용 커플러는 작동가능한 상태로 남아 있어야 합니다.
17. 기기의 공기매개 잡음은 70dB을 초과하지 않아야 합니다.
18. CLASS I 구조의 기기는 MAINS 소켓 콘센트에 보호 접지 연결 방식으로 연결되어
야 합니다.
19. 화재나 감전 위험을 줄이려면 이 기기를 빗물 또는 습기에 노출시키지 마십시오.
20. 이 제품을 고치려고 시도하지 마십시오. 그렇게 하면 사람이 다치거나 제품이 고장
을 일으킬 수 있습니다.
21. 이 제품은 명시된 작동 온도 범위내에서 사용하십시오.
이 기호는 기기에 전기 쇼크 위험을 유발하는 위험한 전압이
흐른다는 것을 의미합니다.
이 기호는 이 기기와 함께 제공된 문서에 중요한 작동 및 유지
보수 지침의 내용이 들어 있다는 것을 의미합니다.
PETUNJUK PENTING KESELAMATAN
1. BACA petunjuk ini.
2. SIMPAN petunjuk ini.
3. PATUHI semua peringatan.
4. IKUTI semua petunjuk.
5. JANGAN gunakan perangkat ini dekat dengan air.
6. CUKUP DIBERSIHKAN dengan kain lap kering.
7. JANGAN halangi semua bukaan ventilasi. Biarkan jarak yang cukup dengan lubang
udara yang cukup dan pasang sesuai petunjuk pabrik.
8. JANGAN pasang dekat dengan sumber panas seperti radiator, kisi-kisi tungku pemanas,
kompor, atau perangkat lain (termasuk amplifier) yang menghasilkan panas. Jangan
taruh sumber api terbuka pada produk ini.
9. JANGAN gagalkan tujuan keamanan steker terpolarisasi atau jenis pembumian. Steker
terpolarisasi memiliki dua bilah di mana bilah yang satu lebih lebar dari yang lain. Steker
jenis pembumian memiliki dua bilah dan tonjolan pembumian ketiga. Bilah yang lebih
lebar atau tonjolan ketiga disediakan untuk keselamatan Anda. Jika steker yang dise-
diakan tidak cocok dengan stopkontak Anda, hubungi petugas listrik untuk penggantian
stopkontak yang sudah lama itu.
10. LINDUNGI kabel listrik agar aman dari injakan atau jepitan, terutama pada steker, stop-
kontak terbuka, dan titik yang menonjol dari perangkat itu.
11. HANYA GUNAKAN kelengkapan/aksesoris yang ditetapkan pabrik.
12. GUNAKAN hanya dengan kereta dorong, penyangga, tripod, braket atau
meja yang ditetapkan oleh pabrikan, atau yang dijual bersama perangkat
tersebut. Bila menggunakan kereta dorong, gunakan secara hati-hati ketika
memindahkan secara bersama-sama kereta dorong/perangkat tersebut untuk
menghindari cedera karena perangkat terguling.
13. CABUT perangkat ini selama petir atau bila tidak digunakan untuk waktu yang lama.
14. SERAHKAN semua servis ke petugas ahli. Servis diperlukan apabila perangkat tersebut
sudah rusak dalam cara apapun, seperti kabel catu daya atau steker rusak, cairan ter-
tumpah atau ada benda yang jatuh ke dalam perangkat, perangkat sudah terpapar hujan
atau lembab, tidak bekerja normal, atau perangkat pernah jatuh.
15. JANGAN paparkan perangkat dengan tetesan dan percikan. JANGAN letakkan benda
yang penuh dengan cairan, seperti pot bunga di atas perangkat tersebut.
16. Steker INDUK atau tusuk kontak harus tetap siap digunakan.
17. Kebisingan Perangkat ini yang bersumber dari udara tidak melebihi 70dB (A).
18. Perangkat dengan konstruksi KELAS I harus dihubungkan ke stopkontak soket INDUK
dengan sambungan pembumian untuk pengaman.
19. Untuk mengurangi resiko kebakaran atau sengatan listrik, jangan paparkan perangkat ini
dengan hujan atau lembab.
20. Jangan coba-coba memodifikasi produk ini. Melakukannya dapat menyebabkan cedera
diri dan/atau kerusakan produk.
21. Jalankan produk ini di dalam jarak suhu kerja yang ditetapkan.
Simbol ini menunjukkan bahwa voltase yang berbahaya menimbulkan
resiko atau sengatan yang ada di dalam unit ini.
Lambang ini menunjukkan bahwa terdapat petunjuk kerja dan pemeli-
haraan penting pada bacaan yang melengkapi unit ini.

5
English

Shure UHF-R Wireless
6
Feature Overview
The UHF-R®Wireless Microphone System uses the latest wireless technology, delivers outstanding audio clarity, and is rugged and reliable. It is easy to
set up and operate with advanced features for professional installations requiring multiple wireless microphone systems.
Frequency Band Selection
Shure offers wireless systems in a selection of bands that conform to the different government regulations of specific nations or geographic
regions. These regulations help limit radio frequency (RF) interference among different wireless devices and prevent interference with local public
communications channels, such as television and emergency broadcasts.
The system’s band and frequency range are identified on the face of the receiver and transmitter. For example, “H4 518–578 MHz.”
For information on bands available in your area, consult your local dealer or phone Shure. More information is also available at
Shure’s website (www.shure.com).
Groups and Channels
To transmit audio through a wireless system, the transmitter and receiver must be set to the same radio frequency, or channel. A wide selection of channels
allows more microphones to be used at the same time, since each microphone must operate on a different channel. It also provides a greater choice of
open channels—those that are free from interference from television broadcasts, electronic devices, or other wireless systems.
Agroup is a selection of compatible channels. Wireless microphones work better together when set to channels in the same group.
Automatic Frequency Selection
The following features scan the RF environment to find the best group and channel settings for a particular installation.
• Group Scan—finds the group with the most open channels, then sets all networked receivers to channels in that group.
• Channel Scan—finds the first open channel in the currently selected group and sets the receiver to that channel.
Follow the steps on page 11 for instructions on using these features.
Automatic Transmitter Sync
This feature automatically transfers the group and channel settings from a receiver to a transmitter. You can also program other transmitter settings on a
receiver and transfer those settings too. See page 16.
Interface Lock
This feature locks the receiver and transmitters so that users cannot change settings. The transmitter power switch can also be disabled so that the
transmitter remains on if the power switch is accidentally toggled during a performance.
Audio Gain Structure
The following settings allow you to adjust audio gain throughout the system:
• Sensitivity (bodypack only). A 25 dB range of gain adjustment at the bodypack transmitter input.
• Transmitter Gain. A 30dB range of audio gain adjustment within the transmitter (affects audio level at the receiver, as indicated by the Audio
LEDS.)
• Output Level. 32 dB of attenuation at the receiver output, plus a mute setting.
• Mic/Line switch. –30 dB pad for matching audio levels at the receiver XLR output.
Networking
Each receiver has an RJ-45 port on the back for connecting to other receivers over an Ethernet network. Networking receivers allows you to automati-
cally set channels for all the receivers with a single group scan command. You can also control and monitor all networked receivers through the Shure
Wireless Workbench PC software.
RF Distribution Ports
Use the RF distribution ports to share the signal from a single pair of antennas with up to 10 single or dual receivers within the same frequency band.
The RF ports eliminate the need for antenna splitters or distribution amplifiers. Active circuitry minimizes insertion losses, preserving signal quality.
Input filtering keeps the signal free from out-of-band interference. Distribution circuitry is active only when additional receivers are connected to the RF
distribution ports. When not used, the port circuitry is bypassed, allowing the receiver to be used as a stand-alone component.
Shure Wireless Workbench Software
The Shure Wireless Workbench software on the supplied CD includes a variety of useful tools for installing and managing multiple wireless systems.
Simply install the software on your computer and connect it to a network of receivers to monitor and control receivers and transmitters throughout the
network. (See page 12 for more information on networking).
Instructions on using the Wireless Workbench software are available in the online help files after you install the software.

7
English
System Components
All systems include:
UR4S+ or UR4D+ Receiver
(UR4D+ pictured)
2 Antenna hole plugs
4 Rack Mount Screws with Washers
AA or AAA Batteries
Two Antenna Cables
Two 1/2 Wave Antennas
IEC Power Extension Cable
Ethernet Network Cable with “Ruggedized” plug
Shure’s Wireless Workbench Software
Transmitter Carrying Case
Handheld Systems Include:
Microphone Head (choice of SM58®, SM86, Beta 58A®,
Beta 87A™, Beta 87C™ or KSM9/BK, KSM9/SL)
UR2 handheld transmitter
 Microphone clip
Bodypack Systems Include:
• UR1 Bodypack Transmitter
or
• UR1M Micro Bodypack Transmitter
• Threaded TA4F Adapter



Threaded TA4F Adapter
Two RF Distribution Cables
UR1 UR1M
IEC Power Cable

Shure UHF-R Wireless
8
Receiver Controls and Connectors
antenna A in
12.7V out
150mA
receiver outputs
lift
GND
line
mic
sync
RF Audio
OL
A B
XX YYY-ZZZ MHz Navigate
ENTER
EXIT
OFF
push
Control POWER
Monitor
Monitor Clip
push
antenna B in
12.7V out
150mA
2
3
4 5
6 7 8
10 11 11 12 13 14 15 16
17
UR4S+
Wireless Receiver
with Audio Reference Conpanding
17

18
189
200Ω
balanced low Z
RF B out RF A out
networking
ethernet
RJ-45
network
activity
 SYNC Infrared (IR) port. Transmits group, channel, and other
settings to a transmitter. See page 16.
Squelch LEDs.
• Blue (On) = Transmitter signal detected
• Off = no signal or signal squelched because of poor reception or
no tonekey
NOTE: The receiver will not output audio unless at least one
blue LED is illuminated.
RF LEDs. Indicate RF signal strength from the transmitter at
each antenna and diversity condition.
• Amber = normal
• Red = overload (greater than –25 dBm)
4 Audio LEDs. Indicate audio signal strength from transmitter.
• Green = signal present
• Yellow = normal peak
• Red = overload
To correct this level, adjust the transmitter gain.
5 Indicates the name and range of receiver frequency band.
LCD Interface. Provides a convenient way to program the
receiver from the front panel (see detail on next page).
7 Monitor. 1/4” output jack and volume knob for headphones.
• Monitor Clip LED indicates headphone audio is clipping.
• Dual models: Push the knob to switch from receiver one to
receiver two.
 Power switch.Powers the unit on and off.
 AC mains power input, IEC connector. 100–240 Vac.
 AC mains power passthrough (unswitched). Use IEC
extension cables to connect up to five UR4+ receivers to a
single AC power source.
 Diversity antenna inputs A and B.
Note: Antenna inputs are DC biased. Use only antenna
combiners and accessories listed in page 21. Some types of
antenna splitters or other products may short the DC power
and damage the receiver.
 Mic/Line switch. Changes output level 30 dB (XLR output only).
 Electrically balanced XLR output jack
 Lift/GND switch. Lifts ground from Pin 1 of the XLR connector
(default = GND).
 Impedance balanced 1/4” output jack (200Ω)
 RJ-45 jack for Ethernet network interface. Accepts both regular
and “ruggedized” RJ-45 plugs.
 Temperature-activated fan ensures top performance in high
temperature environments. Clean fan screen as needed to
remove dust.
 The RF distribution ports pass the RF signal from one receiver to
the next, allowing a maximum of 10 receivers to share a single
pair of antennas.
Note: The diagram above represents the UR4S single channel receiver. The UR4D dual channel receiver is functionally identical to the UR4S, adding a
second LCD interface and set of output jacks for channel 2.

9
English
Receiver LCD Interface
Menu Access
Press the Navigate key next to the menu
item you want to select.
Radio
Audio
Util
SHURE
G: 3 Ch: 1 Out: -0dB
+12 dB
+Hi
524-025 MHz TV: 32
Sync
F, P, FP
Accept Changes
After changing a parameter, the ENTER button flashes. Press
it to save the value.
Cursor Control
Push the Control wheel to move the
cursor to the next item.
Turn the Control wheel to change a
parameter value.
Exit/Cancel
Press the Exit button to cancel changes and
return to the previous menu.
Transmitter Status Display
Everything under the dotted line reflects the
settings for the transmitter, if present. (main
title screen only).
Receiver Parameters
Use the following instructions to set parameters through the LCD interface.
NOTE: After adjusting a parameter, you must press the flashing ENTER button to accept the change.
Group and Channel
Menu: Radio
• Push the Control wheel to move the cursor to the Group (G)
or Channel (Ch) parameter.
• Turn the Control wheel to change the parameter.
Frequency
Menu: Radio
• Push the Control wheel to move the cursor to the integer
value (524.025 MHz) or fractional value (524.025).
• Turn the Control wheel to change the value.
Automatic Transmitter Sync
Menu: Sync
• See page 16.
Receiver Name
Menu: Util
• Turn the Control wheel to change the letter.
• Push the Control wheel to move to the next letter.
Output Level
Menu: Audio
This setting adjusts the signal level at the XLR and 1/4” audio output jacks.
• Turn the Control wheel to change the relative level in dB.
(0 dB to –32 dB).
• Turn the wheel all the way down to mute the outputs.
Squelch
Menu: Radio >Squelch
• Turn the Control wheel to change the parameter
Receiver Lock
When locked, the receiver settings cannot be changed from the front
panel. However, you can still navigate the LCD menu to view the settings
(and turn the lock off).
Menu: Util >Lock
• Turn the Control wheel to toggle the lock on or off (ON or
OFF).
LCD View
Menu: Util >Title
• Turn the Control wheel to mark an item for display.
• Push the Control wheel to move to the next item.
LCD Contrast
Menu: Util > Contrast
• Turn the Control wheel to increase or decrease contrast.
Tonekey
Menu: Radio > Squelch > Tonekey
Tonekey squelch mutes the outputs unless the receiver detects a
transmitter. Tonekey should be left on (On) except for certain
troubleshooting operations.

Shure UHF-R Wireless
10
Network Parameters
NOTE:
• The receiver reboots after you press ENTER to accept network
parameter changes
• In dual models (UR4D+), these settings affect both receivers
(the dual receiver is treated as a single network device).
Set the Receiver Network Mode
Menu: Util > Network
1. Push the Control wheel to move the cursor to the Mode
parameter.
2. Turn the Control wheel to set the receiver to one of the
following values:
• DHCP: use this setting when connecting the receiver to a DHCP
server.
• Manual: allows you to set the receiver to a specific IP address
or subnet.
IP Address and Subnet
Menu: Util > Network
NOTE: To change these settings, the network mode
must be set to Manual.
1. Push the Control wheel to move the cursor to any of the
following parameters:
• IP (IP address)
• Sub (Subnet mask)
2. Turn the Control wheel to change the value.
Device ID
Assists in identifying receivers through the Wireless Workbench Software
(has no effect on network identification).
Menu: Util > Network
1. Push the Control wheel to move the cursor to the DevID
parameter.
2. Turn the Control wheel to set the receiver to change the value.
Custom Groups This feature allows you to create your own groups of
frequencies.
Creating new groups...
Menu: Radio > Custom
1. Turn the Control wheel to select a custom group number (U1,
U2, U3, etc.)
2. Push the Control wheel to move to the Channel parameter
and turn it to select a channel (01, 02, 03, etc.)
3. Push the Control wheel to move to the Freq parameter and
select a frequency for that channel.
4. Push the NEXT menu key to select a frequency for the next
channel in that group.
To Antenna ATo Antenna B
Connecting Multiple Receivers to the RF Distribution Ports
The RF distribution ports pass the RF signal from one receiver to the next, allowing a maximum of 10 single or dual receivers to share a single pair of
antennas.
Use the supplied RF distribution cables to connect the ports of each receiver as shown.
NOTE: All receivers must be operating in the same frequency band.
First Receiver
Additional Receivers
Last Receiver
Antenna A in
RF A out
Antenna A in
RF A out
Antenna A in
RF A out

11
English
Automatic Frequency Selection
Follow these steps to use the channel scan and group scan features.
Before you begin...
• Install the receivers in the location where they will be used and power them on.
• Mute all inputs on mixing devices connected to receivers.
• Turn off all bodypack or handheld transmitters for the systems you are setting up.
• Turn on potential sources of interference such as other wireless systems or devices, computers, CD players, effects processors, and digital
rack equipment so they are operating as they would be during the presentation or performance.
Single Receiver
1. Select Radio > Scan > Chan Scan using the Navigate keys on the receiver LCD interface.
2. Turn the Control wheel to select a group.
3. Press Chan Scan. The display indicates that the receiver is searching. Once it has finished, it displays the selected channel.
4. Press the flashing ENTER button to accept the suggested channel.
5. Sync the transmitter (see page 16).
Networked or Dual Receivers
With networked or dual receivers, you can take advantage of the group scan feature to set group and channel settings for all the receivers at the same
time. (See page 11 for instructions on networking.)
Perform a group scan from any receiver...
1. Select Radio > Scan> Group Scan using the Navigate keys on the receiver LCD interface. The display indicates that the receiver is
searching (Scan In Progress). Once it has finished, it displays the group with the most open channels.
2. If you wish, turn the Control wheel to change groups. The number of open channels for each group is displayed.
3. Press the flashing ENTER button to set all receivers to open channels in that group.
NOTE: The group scan feature only works for receivers in the same frequency band. For example, if you did a group scan on a “H4” band
receiver, all “H4” band receivers would be set up, but not “J5” band receivers.
Multiple Receivers—Not Networked
If your receivers are not networked (or in different bands), the group scan cannot automatically set their group and channel settings. However, you can
still take advantage of the group scan feature to find the group with the most open channels and the channel scan feature to find open channels in that
group.
Find the group with the most open channels...
Perform a group scan using the steps for a networked receiver (above). However, make a note of the selected group before pressing the flashing ENTER
button to accept it.
Set the receivers to open channels in that group...
Perform a channel scan on the remaining receivers using the steps for a single receiver (above). Make sure to select the same group for each receiver
before performing the channel scan.
IMPORTANT: After setting the channel for the first receiver, immediately sync the transmitter for that receiver and leave it on so that the
next receiver detects that channel during its channel scan. Otherwise, all the receivers will be set to the same open channel.
NOTE: Receivers in different bands (H4, J5, L3, etc.) do not need to be set to the same group.

Shure UHF-R Wireless
12
Networking Receivers
Basic Network
Connect receivers to an Ethernet router with DHCP service. Use Ethernet switches to
extend the network for larger installations.
Use the receiver’s default network setting
(Util > Network > Mode = DHCP).
Accessing the Network with a Computer
If you want to use the Wireless Workbench software, connect your computer to the
network and install the software from the CD that came with the receiver. Make sure
your computer is configured for DHCP (from Control Panel, click Network Connections.
Double-click on Local Area Connection. Select Internet Protocol (TCP/IP) and click
Properties. Select Obtain IP address automatically and Obtain DNS server address
automatically and click OK).
NOTE: Some security software or firewall settings on your computer can
prevent you from connecting to the receivers. If using firewall software, allow
connections on port 2201.
Static IP Addressing
The receiver also supports static IP addressing. Assign your own IP addresses ( Util > Network > Mode = Manual). See “Network
Parameters” on page 10.
NOTE: Dual receivers use a single IP address, which may be set through either LCD interface.
Router with DHCP
Computer
(optional)
Switch
Switch
Ethernet
Router with DHCP
Computer
(optional)

13
English
Handheld and Bodypack Transmitter Controls and Connectors













Interchangeable microphone head (BETA 87A pictured).
LCD Panel.
 Power Switch.
 Control buttons for LCD interface.
 Infrared (IR) port. See page 16.
 Battery compartment.
 Flexible Antenna.
 Power LED.
 4-Pin Microphone Input Jack.
 Reversible Belt Clip. UR1M
UR1M Micro bodypack Transmitter
The following specifications apply to the UR1M micro bodypack only.
Features:
• Same audio performance as UR1
• Rapid two-way infrared (IR) data transmission
• User-adjustable RF output level (10 mW or 50 mW)
• Operates with three types of primary batteries: alkaline, lithium
or NiMH
• Audio signal is input through a TA4F connector (UR1M) or a
LEMO connector (UR1MLEMO3)
• Selectable battery metering by battery type
• Audio metering on UR1M transmitter
Battery Life (Typical):
Alkaline: 6 hours (normal RF power)
4 hours (high RF power)
Lithium primary: 9 hours (normal RF power)
7 hours (high RF power)
NiMH 1000 mAH: 6 hours (normal RF power)
4 hours (high RF power)
Select Battery Type:
Set the micro bodypack transmitter switch to on
Press enterkey, then scroll using button to select battery type.
Press enterkey to confirm.
Note: For the most accurate battery metering and
performance, make sure to select the correct battery type.
To open the micro bodypack transmitter, see illustrations below:
Slide arrow down
RF Carrier Frequency Range
470-865, 944-952 MHz depending on region
Working Range
150 m (500 ft.), under typical conditions 500 m
(1600 ft.) line-of-sight, outdoors for a single system
NOTE: Actual working range depends on RF signal
absorption, reflection and interference
RF Power Output
Selectable 10 mW or 50 mW depending on region
Power Requirements:
Two 1.5V AAA alkaline, lithium primary, and NiMH batteries
Current Drain:
130 mA max. at 3V (normal RF power setting)
200 mA max. at 3V (high RF power setting)
Gain Adjustment Range
–20 to +35 dB
–10 dB recommended for guitars
Overall Dimensions
47.5 mm L x 63 mm W x 17mm D (1.9 x 2.5 x 0.67 in)
Net Weight
64 g (2.3 oz.) without batteries

Shure UHF-R Wireless
14
Transmitter Batteries
Transmitters operate on standard AA batteries. Turn off the transmitter before changing the batteries.
The battery fuel gauge displayed on the transmitter LCD gives an indication of remaining battery life, as shown below.
UR1, UR2:
Transmitter Display Approximate Hours Remaining (alkaline batteries)
UR1/UR2 (Normal Power) UR1/UR2 (High Power*) UR1M
7.5 to 9.5 5 to 6 5
5.75 to 7.5 4 to 5 4
4 to 5.75 3 to 4 3
2 to 4 1.5 to 3 2
15 minutes to 2 hours 10 minutes to 1.5 hours 1
* High power setting not available with models sold in countries that prohibit its use.
Transmitter LCD Interface
Main Menu
Up Arrow Key. Scroll up
or increase a value.
enter Key. Press to select parameters
and accept the selected value.
Down Arrow Key. Scroll
down or decrease a value.
exit Key. Move to the left, or exit
without saving changes.
779.475MHz

15
English
Transmitter Parameters
Press ENTER from the main menu to access the following parameters:
SHURE INC.
G:34 Ch:21
779.475MHZ
Gain +20dB
Group (G) and Channel (Ch). Must match the receiver’s settings.
Frequency (MHz). Manual frequency selection in 0.025 MHz increments.
Gain (Gain). Adjusts audio level from –10 dB to +20 dB
Sensitivity (Sens) (bodypack only).
Sets audio input to +15 dB, 0 dB, or –10 dB recommended for guitars.
Name Display. 12-digit ASCII.
Use the following key combinations to access additional features and parameters:
LCD Panel
Changes LCD Panel
Frequency Lock
Toggles setting. When enabled, frequency cannot be changed, and a transmitter sync will
not overwrite the frequency setting.
Power Lock
Toggles power lock. When locked, power switch does not turn off transmitter.
RF power level setting*
Use the arrow keys to select normal (10 mW) or high power (50/100 mW**). Use the normal power setting to conserve
batteries or prevent RF overload at the receiver.
* High power setting not available with models sold in countries that prohibit its use.
** High power value varies with model.
Lock Indicators
Power Lock
Frequency Lock
Setting Transmitter Gain
Adjust the transmitter gain and input sensitivity so that the Audio LEDs on the receiver peak within the yellow range during use. On the bodypack
transmitter, you can change the sensitivity setting to compensate for different audio levels when connecting different instruments or microphones to the
input.
To adjust gain, turn on the transmitter and press the enter button. Scroll down to the Gain parameter or the Sens parameter (bodypack only) and
press enter again. Use the arrow keys to adjust the setting and press enter to save it (Exit cancels without saving).
RF Safety Mode
This special feature temporarily mutes RF broadcast. This allows you to change frequency settings on a transmitter without accidentally “cutting in” on a
channel being used by another transmitter.
1. Turn the transmitter off.
2. Hold down exit key while turning on the transmitter power (for handheld microphones, you need to pull the battery cover off the handle). The
LCD flashes while the unit is in RF safety mode.
3. Change group and channel settings as you normally would—the transmitter will not broadcast.
4. Power the transmitter off and on to exit RF safety mode.
TapHold
TapHold
TapHold
TapHold

Shure UHF-R Wireless
16
Automatic Transmitter Sync
This feature automatically updates a bodypack or handheld transmitter’s group and channel settings to match those of a selected receiver.
To perform a transmitter sync...
1. Open the transmitter battery cover to display the infrared (IR) port.
2. With the IR port exposed to the receiver, select Sync > sync from the receiver LCD interface.
The display on the receiver indicates whether the sync was successful. If the sync fails, try again, making sure that the IR port on the transmitter is
exposed and directly faces the IR port on the receiver.
NOTE: Close the battery door before performing a sync on other transmitters.
Audio ABJ 779-810 MHz NavigateRF
OL OL
Audio ABJ 779-810 MHz NavigateRF
®
UR4D+
Wireless Receiver
with Audio Reference
Companding
sync
Control Monitor Power
sync
Monitor Clip
ENTER
EXIT
push
1
2
To transfer other transmitter settings...
Optionally, you can transfer other transmitter settings from a receiver when you perform a sync. Use the following steps:
1. Select Sync > Setup from the receiver LCD interface.
2. Turn the Control wheel to change parameter settings.
3. Push the Control wheel to move to the next parameter.
4. Push the flashing ENTER button to save the settings.
The transmitter settings you set on the receiver remain for future syncs.
NOTE: If you don’t want the sync to send a setting, set the parameter to No Change
Available Settings...
The following settings are available from the Sync > Setupmenu:
• Sensitivity (Sens) bodypack only
• Gain (Gain)
• RF Power (Pwr)
• Power and Frequency Lock (Lock), which has the following values:
Power lock only: (Pwr Only)
Frequency lock only: (Freq only)
Both: (Freq and Pwr)
Neither: (Unlocked)
• Custom Groups (CG):
On (ON): Send custom groups to transmitters during sync
Off (OFF): Do not send custom groups (reduces sync time)

17
English
Troubleshooting
Issue See Solution...
No sound Power, Cables, or RF
Faint Sound or Distortion Gain
Lack of range, unwanted noise bursts, or drop outs RF
Cannot turn transmitter off or change frequency settings, or can’t program receiver Interface Locks
Excessive hum or buzzing Ground lift
Power
Make sure that the transmitter and receiver are receiving sufficient
voltage. The receiver requires at least 90 Vac. Check the battery indicator
on the transmitter and replace battery if necessary.
Gain
Adjust the transmitter gain and sensitivity settings (see page 15) or the
receiver output level (page 9), or toggle the mic/line switch on the back
of the receiver.
Cables
Check that all cables and connectors are in working order.
Ground Lift
Lifting the ground on pin 1 of the XLR output on the receiver can
sometimes remove hum or buzz in the audio signal. Set the GND/LIFT
switch on the receiver to LIFT if you are using the XLR connector.
Interface Locks
Both the transmitter and receiver can be locked to prevent accidental
changes. On transmitters, look for a lock symbol on the LCD and use the
key combinations illustrated on page 15 to turn it off.
To turn off the receiver interface lock, see page 9.
Increasing Range
If the transmitter is more than 6 to 60 m (20 to 200 ft) from the receiver
antenna, you may be able to increase range by doing one of the following:
• Reduce interference (see above)
• Increase transmitter RF power level (see page 15).
• Use an active directional antenna, antenna distribution system, or
other antenna accessory to increase RF range (see page 21).
Radio Frequency (RF)
Using the RF LEDs
If neither blue RF LED is illuminated, then the receiver is not detecting the
presence of a transmitter.
The amber RF LEDs indicate the amount of signal being received. This
signal could be from the transmitter, or it could be from an interfering
source, such as a television broadcast. Turn the transmitter off. If more
than one or two of the amber RF LEDs are still illuminated, then that
channel has too much interference, and you should try a different channel.
The red RF LED indicates RF overload. This will usually not cause a
problem unless you are using more than one system at the same time, in
which case, it can cause interference between systems.
Eliminating RF Overload
If you see the red RF LED on a receiver, reduce the transmitter RF
power level (see page 15) or move the transmitter further away from the
receiver—at least 6 m (20 ft). If you are using active antennas, reduce
antenna or amplifier gain.
Compatibility
• Perform a transmitter sync, or make sure the transmitter and
receiver are set to the same group and channel.
• Look at the label on the transmitter and receiver to make sure
they are in the same band (H4, J5, L3, etc...).
Reducing Interference
• Use a different channel or perform an automatic group or channel
scan (see page 11).
• For multiple systems, check that all systems are set to channels
in the same group (systems in different bands do not need to be
set to the same group).
• Maintain a line of sight between transmitter and receiver
antennas
• Move receiver antennas away from metal objects or other
sources of RF interference (such as CD players, computers,
digital effects, network switches, network cables and Personal
Stereo Monitor (PSM) wireless systems).
• Eliminate RF overload.

Shure UHF-R Wireless
18
RF Carrier Frequency Range
470-865, 944-952 MHz depending on region
Working Range
UR1, UR2
150 m (500 ft.), under typical conditions
500 m (1600 ft) line-of-sight, outdoors for a single system.
NOTE: Actual working range depends on RF signal absorption, reflection
and interference.
Audio Frequency Response
40 – 18,000 Hz, (+1 dB, –3 dB).
NOTE: Overall system frequency response depends on the microphone
element
Gain Adjustment Range
UR1: –20 to +35 dB
–10 dB recommended for guitar
UR2: –10 to +20 dB
Modulation
FM (45 kHz max. deviation), compander system with pre- and de-emphasis
RF Power Output
See table above.
maximum variation of -1.5 dB
Dynamic Range
>105 dB, A-weighted
Image Rejection
>110 dB typical
SPECIFICATIONS
Band Range Transmitter power (Nominal mW)
Handheld
UR2
BodyPack
UR1
Bodypack
UR1M
G1 470-530 MHz 10 / 50 10 / 100 10 / 50
G1E 470-530 MHz 10 / 50 10 / 50 10 / 50
G7C 470.125–509.875 MHz 10 / 50 10 / 50 10 / 50
H4 518-578 MHz 10 / 50 10 / 100 10 / 50
H4E 518-578 MHz 10 / 50 10 / 50 10 / 50
J5 578-608, 614-638 MHz 10 / 50 10 / 100 10 / 50
J5E 578-638 MHz 10 / 50 10 / 50 10 / 50
K4E 606-666 MHz 10 / 50 10 / 50 10 / 50
L3 638-698 MHz 10 / 50 10 / 100 10 / 50
L3E 638-698 MHz 10 / 50 10 / 50 10 / 50
M5E 694-758 MHz 10 / 50 10 / 50 10 / 50
P8 710–790 MHz 10 / 50 10 / 50 10 / 50
P9 710–787 MHz 10 / 50 10 / 50 10 / 50
Q5 740-814 MHz 10 / 50 10 / 50 10 / 50
R9* 790-865 MHz 10 / 50 10 / 50 10 / 50
Q6 740-752 MHz 10 10 10 / 50
A24 779-788 / 797-806 MHz 10 10 10
JBX 806-810 MHz 10 10 10
Q10A 740-787 MHz 10 / 50 10 / 50 10 / 50
R16 794-806 MHz 10 / 50 10 / 50 10 / 50
R18 794-806 MHz 10 only 10 only 10
X1 944-952 MHz 10 / 50 10 / 100 10 / 50
RF Sensitivity
UR4S+ UR4D+
–110 dBm Typical
12 dB SINAD
–107 dBm Typical
12 dB SINAD
–105 dBm Typical
30 dB SINAD
–102 dBm Typical
30 dB SINAD
Spurious Rejection
>90 dB typical
Ultimate Quieting (ref. 45 kHz deviation)
>100 dB, A-weighted
Signal Polarity
Positive pressure on microphone diaphragm (or positive voltage applied to
tip of WA302 phone plug) produces positive voltage on XLR output pin 2
with respect to XLR pin 3 and on the tip of the 1/4-inch output jack.
System Distortion (ref. ± 45 kHz deviation, 1 kHz modulation)
<0.3% Total Harmonic Distortion typical
Power Requirements
UR1, UR2: Two 1.5V AA batteries
UR1M: Two 1.5V AAA batteries
UR4+:100 to 240 VAC, 50/60 Hz
Current Drain
UR1, UR2: 180 mA max. (normal RF power setting)
240 mA max. (high RF power setting)
UR4D+, UR4S+: 0.8 Amps max.
Battery Life (Typical)
UR1, UR2: 9.5 hours (normal RF power),
6 hours (high RF power)
UR1M: 5 hours (normal RF power)
3 hours (high RF
Operating Temperature Range
–18° to +57° C (0° to +135°F)
NOTE: Battery characteristics may limit this range
NOTE: Electrical safety approval is based on a maximum ambient
temperature of 35°C (95°F)
NOTE
This Radio equipment is intended for use in musical professional entertainment
and similar applications.
This Radio apparatus may be capable of operating on some frequencies not
authorized in your region. Please contact your national authority to obtain
information on authorized frequencies and RF power levels for wireless
microphone product
Overall Dimensions
UR1: 98 mm L x 60 mm W x 17 mm D (3.84 x 2.38 x 0.66 in.)
UR2/SM58: 261 mm L x 51 mm Dia. (10.27 x 2 in.)
UR2/SM86: 261 mm L x 51 mm Dia. (10.27 x 2 in.)
UR2/SM87A: 254 mm x 51 mm Dia. (10 x 2 in.)
UR2/KSM9/BK, UR2/KSM9/SL: 250 mm x 49 mm Dia. (9 7/8 x 1 15/16 in.)
UR2/BETA 58: 258 mm L x 51 mm Dia. (10.15 x 2 in.)
UR2/BETA 87A, UR2/BETA 87C: 254 mm x 51 mm Dia. (10 x 2 in.)
UR4S+/UR4D+: 44 mm H x 483 mm W x 366 mm D
(1.72 x 19.00 x 14.39 in.)
Net Weight
UR1: 97 g (3.4 oz.) without batteries
UR2/SM58: 356 g (12.6 oz.) without batteries
UR2/BETA 58: 314 g (11.1oz.) without batteries
UR2/SM86: 317 g (11.2 oz.) without batteries
UR2/SM87A: 298 g (10.5 oz.) without batteries
UR2/KSM9/BK, UR2/KSM9/SL: 410 g (14.5 oz.) without batteries
UR2/BETA 87A, U2/BETA 87C: 325 g (11.5 oz) without batteries
UR4S+: 4.8 kg (10.6 lbs)
UR4D+: 5.0 kg (11.0 lbs)
Housing:
UR1, UR1M: Cast magnesium
UR2: Aluminum die-cast handle and aluminum machined battery cup
UR4S+, UR4D+: Galvanized steel

19
English
Inputs and Outputs
UR1 Transmitter Audio Input
Connector: 4-Pin male mini connector (TA4M)
Input Configuration: Unbalanced, active
Maximum Input
Level:
(1 kHz, 1% THD)
+10 dBu (sensitivity 0 dB)
+20 dBu (sensitivity –10 dB)
TA4M Connector Pin
Assignments:
Pin 1: Ground
Pin 2: +5 Vdc bias
Pin 3: Audio, 200 kΩ
Pin 4: Tied through active load (on main board)
to Ground.
(On instrument adapter cable, Pin 4 floats)
UR1M Transmitter Audio Input:
Connector: 4-Pin male mini connector (TA4M)
3-Pin female mini connector (LEMO XRB.00.303)
Input Configuration: Unbalanced, active
Maximum Input
Level:
(1 kHz, 1% THD)
+5 dBu (sensitivity 0 dB)
+15 dBu (sensitivity –10 dB)
TA4M Connector Pin
Assignments:
Pin 1: Ground
Pin 2: +5 VDC bias
Pin 3: Audio, 200 kΩ
Pin 4: Tied through active load (on main board)
to ground.
(On instrument adapter cable, Pin 4 floats)
LEMO Connector Pin
Assignments:
Pin 1: Ground
Pin 2: +5 VDC bias
Pin 3: Audio
(8.2 kΩ between pin 2 and 3, internal to UR1M)
UR2 Transmitter Audio Input
Input Configuration: Unbalanced, active
Actual Impedance: >1 MΩ
Maximum Input Level:
1 kHz, 1% THD
+4.8 dBu
UR1, UR1M Transmitter RF Output
Connector: SMA
Actual Impedance: 50 Ω
Pin Assignments: Shell = Ground
Center = Signal
LEMO Connector
Connector
Connector
UR1M LEMO BOARD
Audio
Ground
Microphone Element
Wiring for TA4F:
MICROPHONE
ELEMENT TA4F
Connector
TA4M
Connector
NOTE: LAVALIER MIC TIES PINS 3 AND 4 TOGETHER—GUITAR CABLE DOES NOT.
UR1 MIC JACK BOARD
Active Load
Audio
Ground
Receiver Audio Output
Monitor (1/4”
Headphone)
1/4” Phone XLR
Output
Configuration:
Unbalanced
mono, 1/4 inch
Impedance
Balanced
Electrically
Balanced
Actual
Impedance:
50 Ω200 Ω200 Ω (active
balanced)
(150 Ω mic)
Maximum
Output Level:
1 Watt @ 63 Ω+18 dBu +24 dBu
(–6 dBu mic)
with 100 Hz
modulating tone
Pin
Assignments:
Tip = Hot
Ring = Hot
Sleeve = Gnd
Tip = Hot
Ring = no signal
Sleeve = Gnd
1 = Ground
2 = Audio +
3 = Audio –
Phantom Power
Protection:
No Yes Yes
Receiver Input
Antenna Power
Connector Type: BNC IEC
Actual Impedance: 50 Ω-
Nominal Input
Level:
–95 to –30 dBm 100-240 VAC, 50/60 Hz
Maximum Input
Level:
–20 dBm 240 VAC, + 10%, 50/60 Hz
Pin Assignments: Shell = Ground
Center = Signal
IEC Standard
Bias Voltage* 12 Vdc @ 150 mA
maximum
N/A
* For remote antenna amplifiers
Computer/Network Interface
Ethernet
RJ45
RF Distribution Ports
RF IN RF OUT
Connector Type BNC BNC
Vdc Bias 12 Vdc @ 150 mA N/A
NOTE: The RF distribution circuitry is activated only if connected to an RF
input that has 12 Vdc bias.
Each UR4+ RF antenna input port provides 12 Vdc bias @ 150 mA.
The 12V dc bias is present only when the UR4+ receiver is powered on.
Therefore, if a cascaded UR4+ Receiver is powered off, the RF signal will
not appear in the UR4+ receivers that follow the powered-off receiver.

Shure UHF-R Wireless
20
1/4" Phone 1/4" Monitor/headphone
XLR
Switch
GND
Lift