Sibata QC-10N User manual

CODE 080860-110
Quick Charger QC-10N Operation Manual
Thank you for buying the QC-10N Quick Charger. Before
using the QC-10N, be sure to thoroughly read this manual to
ensure correct use.
Also, keep this manual in a safe place so that it can be
referred to whenever necessary.
- 1 -
14.09.11H (04)
Safety Precautions
The precautionary information that appears in this manual is
for ensuring that the product is used safely and for
preventing injury to you and other people and damage to
equipment.
It is all important for ensuring safety and so be sure to read
it thoroughly before using the product and observe it during
use.
Warning Indications
DANGER: Impending danger is expected
that might result in death or
serious injury.
WARNING: There is an expected risk that
might result in death or serious
injury.
CAUTION: There is an expected risk of
serious injury or property
damage.
- 2 -
DANGER
Misuse might cause electric shock, generation of
heat, fire, or rupturing, which will result in burns,
serious injury or blindness.
• Never use the QC-10N for charging devices other than
the LI-10N. Also, never use the QC-10N for devices other
than the MP-ΣN / MP-ΣNⅡSeries.
• Never connect an AC adapter other than the exclusive AC
adapter (RC60G-12DSBS) (provided) to the QC-10N.
• Do not disassemble or modify the QC-10N and
RC60G-12DSBS.
• Do not insert metal objects inside the product body.
• Do not leave the product near infants.
• Do not immerse the product in water or allow it to get wet.
• If you notice heat generation or abnormal odors,
immediately disconnect the plug from the AC power
outlet.
• Do not place heavy objects on the QC-10N or
RC60G-12DSBS, or subject them to dropping or other
impact.
- 3 -
WARNING
Misuse might cause electric shock, generation of
heat, fire, or rupturing, which will result in burns,
injury or blindness.
• When connecting or disconnecting the LI-10N or MP-ΣN /
MP-ΣNⅡSeries, be sure to do so by holding the connector.
• Do not connect to an electronic type transformer.
• Do not charge a short-circuited LI-10N.
• Do not use the QC-10N near objects that generate heat or
block heat discharge.
• Insert each of the connectors firmly as far as possible.
- 4 -
CAUTION
Misuse might cause obstruction or physical damage.
• Connect connectors correctly.
• Charge indoors within a temperature range of 0 to 40°C.
• Do not charge or store in humid or dusty locations.
• When not charging, be sure to disconnect the
RC60G-12DSBS from the AC power outlet.
- 5 -

Features
zCan charge the LI-10N Battery Unit exclusively for the
MP-ΣN / MP-ΣNⅡseries.
zCan supply power for the MP-ΣN / MP-ΣNⅡseries while
simultaneously charging the LI-10N.
zBuilt-in micro-computer to enhance anti-overcharging and
anti-overheating functions.
zSimple battery voltage check.
zThe battery temperature is detected to charge at the
appropriate temperature (0 to 40°C).
zCompliant with RoHS directives.
- 6 -
Connection Drawings
- 7 -
Connector Specifications
Input side Output side
LED Display
During Charging Simple Voltage Check
Red Green Red Green
Charging UFlashing Normal
voltage {Lit {Lit
Charging
completed {Lit Low voltage {Lit UFlashing
Temperature
standing by {Lit
Error UFlashing UFlashing
- 8 -
Handling Method
(1) When connected as shown in the figure on the left,
charging is started and the red LED flashes.
* When connected with the LI-10N installed on the MP-ΣN
/ MP-ΣNⅡseries, the LI-10N can be charged and the
QC-10N can be driven as the AC power source of the
MP-ΣN / MP-ΣNⅡseries.
When charging is completed, the red LED stops flashing
and the green LED lights up.
* The QC-10N only charges when connected directly to
the charging connector on the LI-10N.
(2) If the red LED is lit even with the QC-10N connected,
charging is not possible since the battery temperature at
the start of charging is out-of-range. In this case,
charging will start automatically as soon as the battery
temperature returns to within the battery temperature
range. The appropriate charging temperature range is 0
to 44 °C.
* Charging will stop midway if the battery temperature falls
out of the temperature range 0 to 46°C. In this case, too,
the red LED will light, and charging will start
automatically as soon as the battery temperature returns
to within the battery temperature range.
- 9 -
(3) When both red and green LEDs are flashing, an error
has occurred. If the cause of the error is unknown,
contact your Sibata agent.
(4) The simple battery voltage check can be performed by
pressing the button on the left of the LEDs.
When both red and green LEDs light after pressing the
button, the voltage is 8.2 V or more, and you can judge
that the battery is about 80% charged.
When the red LED is lit and the green LED is flashing,
the voltage is less than 8.2 V, which means that the
battery must be charged.
* In a fully charged state (with the green LED lit), this
function cannot be used.
- 10 -
Specifications
Item code 080860-110
Model QC-10N
Input voltage range 12 VDC (RC60G-12DSBS must be used)
Output voltage range 8.4 VDC (1.8 A), 12 VDC (1 A)
Operating temperature range 0 to 40°C
External dimensions 85 (W) ×120 (D) ×29 (H) mm
Weight Approx. 150 g
Compliant with RoHS directives
Exclusive AC adapter RC60G-12DSBS [connector shape B type]
Input voltage 100 to 240 VAC 50/60 Hz *
Output voltage 12 VDC (4 A)
External dimensions 53 (W) ×118.4 (D) ×33.5 (H) mm
Weight Approx. 350 g
Standards PSE, UL, CE
Compliant with RoHS directives
*(A power supply cable for Japanese market included)
If the power supply voltage exceeds 100 V, provide a power
supply cable that complies with the laws, regulations, and
safety standards of the country or region where it is being
used.
- 11 -
12 V
To AC power outlet
QC-10N
Exclusive AC adapter
RC60G-12DSBS
Output side
Input side
To MP-ΣN / MP-ΣNⅡ
Series power connector