Siegenia AERO AEROMAT 80 User manual

AERO
Sound absorbing ventilator.
AEROMAT 80
Window systems
Door systems
Comfort systems
ASSEMBLY AND
OPERATING INSTRUCTIONS

Assembly and operating instructions AEROMAT 80
308.2021
Contents
Target group of this documentation................................................................................................................................................ 4
Intended use.................................................................................................................................................................................... 4
Installation ....................................................................................................................................................................................... 5
Unit description ............................................................................................................................................................................... 6
Operation........................................................................................................................................................................................ 7
Maintenance................................................................................................................................................................................... 7
Cleaning.......................................................................................................................................................................................... 7
Accessories ..................................................................................................................................................................................... 9
Technical specifications ................................................................................................................................................................10
Dimensions ....................................................................................................................................................................................10

4
AEROMAT 80 Assembly and operating instructions
08.2021
Target group of this documentation
This documentation is addressed exclusively to specialist companies. All work described in this document is to be performed
exclusively by experienced professionals with training and practice in the assembly, installation and maintenance of
ventilation units. Safe and proper assembly of this unit is not possible without expert knowledge.
Intended use
• The AEROMAT 80 is intended for installation in the exterior windows/walls of permanent structures in accordance with
our installation and design documents as well as the specifications of our assembly instructions and is only suitable for the
ventilation of enclosed rooms.
• Do not use the AEROMAT 80 in environments with corrosive or explosive atmospheres (dust, vapour or gas).
• Use the AEROMAT 80 only with genuine accessories from SIEGENIA.
• Comply with the safety regulations for operating electrical equipment and, if necessary, for ladders, steps and work
overhead or at certain heights.
• Use the AEROMAT 80 only when it is in a technically sound condition.
• Do not modify the unit's components in any way.
• Ventilation openings must be kept free and must not be blocked by other equipment, furniture or objects.
• Please do not put any objects on top of the unit.
• In the event of a fault, only have the AEROMAT 80 repaired by experienced specialists with training and practice in the
maintenance of ventilation units.
• Any use of this product that is not in accordance with its correct use, or any adaptation of or modification to the product
and its associated components for which the express consent of SIEGENIA has not been obtained, is strictly prohibited.
SIEGENIA accepts no liability whatsoever for any material losses or injury to people caused by failure to comply with this
stipulation.

Assembly and operating instructions AEROMAT 80
508.2021
Installation
Prerequisites for installation
• The position from which the outdoor air is drawn in must be selected in such way that any nearby emission sources have
as little impact as possible on the quality of the air being drawn in.
• Installation options:
installation in glazing rebate
AEROMAT
80
installation in impost
AEROMAT
80
Installation sequence
1. Carefully remove AEROMAT 80 from the packaging. We recommend placing the unit on a soft surface (e.g. cardboard
or blanket) during installation.
2. Close the fan flap to prevent contamination (e.g. dust) from entering the unit during installation.
3. Install the AEROMAT 80 in its intended installation position and seal it in accordance with the installation directives
applicable on site.
4. Check AEROMAT 80 for cleanliness prior to starting it up. If necessary, thoroughly clean the unit as described in our
operating instructions.

6
AEROMAT 80 Assembly and operating instructions
08.2021
Unit description
Depending on its version, the AEROMAT 80 is delivered with a left or right-hand operating lever. On the respective opposite
side, there is a small screw for the pressure setting of the fan flap.
1. Pressure setting of the fan flap
2. Fan flap (The airflow is regulated using the operating lever.)
3. Operating lever (The airflow can be continuously set using the operating lever.)
1
3
2
Unit properties
• Sound absorption against external noise
• Weather grille protects against direct snow and rainfall
• Aluminium casing anodised or powder-coated, PVC face plates
• Thermal separation (low heat transfer via the casing)
Pressure differential operation
The room is ventilated as the indoor and outdoor air pressures are equalised.
Normally, air flows from outside into the room.
The air flow into the room varies as the wind pressure changes with the weather.
Rod operating device (optional accessories)
We recommend to use the rod operating device starting at an installation height of 1.80 m or higher (see the "Rod operating
device" and "Accessories" chapters). Do not use any inappropriate auxiliary materials to operate the unit.

Assembly and operating instructions AEROMAT 80
708.2021
Operation
You can shift the operating lever manually. We recommend to use the rod operating device for SIEGENIAat an installation
height of 1.80 m and higher (see chapter "Rod operating device" and "Accessories"). Do not use any inappropriate auxiliary
materials to operate the unit.
Airflow setting
1. Open the fan flap
2. Close the fan flap
1.
2.
Maintenance
If you notice that the ventilator does not close properly or is difficult to open because the compression strength of the fan flap
is not correct, you can adjust the compression strength by means of a small screw on the front panel of the unit.
• Slightly turn the screw into the desired direction using an appropriate screwdriver.
(+ = increase the compression strength; - = decrease the compression strength)
-
+
Besides cleaning it, the AEROMAT 80 does not need any further maintenance. If any malfunctions arise, please contact
SIEGENIA.
Cleaning
Caution!
› Only clean the AEROMAT 80 as to where the unit is accessible safely. Observe the safety regulations for ladders, steps,
works in particular heights etc.
› If required, clean the outer parts of the AEROMAT 80's casing using a suitable cloth, which has been moistened with a
mild soap sud or washing-up liquid.
› Never use cleaning agents that are aggressive or contain solvents, as these may damage the surface of the unit.

8
AEROMAT 80 Assembly and operating instructions
08.2021
Cleaning the front panel and sealing plate
1. Close the fan flap.
2. Lift and remove lid using a flathead screwdriver
1.
2.
3. Lift front panel using a flathead screwdriver
4. Pull out front panel and sealing plate from behind and pull off of the operating lever
3.
4.
5. Lift-off sealing plate and front panel to clean
6. Remove foamed lining, if necessary
7. Make sure that the operating rod (a) does not slip out not of the sealing plate's profile
8. After cleaning, reassemble in the reverse order
5.
6.
a

Assembly and operating instructions AEROMAT 80
908.2021
Accessories
Rod operating device (optional)
The ventilator/fan/blower can be operated using a sliding button on the rod. Push the sliding button up or down to do this.
The sliding button’s "Open" and "Close" positions (or intermediate positions) correspond to the positions of the operating
lever on the unit.
The rodding is mounted on the same door or window element in which the ventilator/fan/blower is mounted. If the ventila-
tor/fan/blower is mounted in a moveable window sash, for example, it is essential to also attach the rodding to the same
sash profile.
Depending on the assembly situation, the pin and the clip must be shortened.
1. Open the fan flap (1.) and plug the pin into the opening of the operating lever (2.).
1.
2.
2. Push the sliding button of the rodding upwards (1.) and plug the top clip over the pin (2.).
1.
1.
2.
3. Push the rodding against the existing profile and hold in place. The upper edge of the rodding must be located 10 mm
above the top edge of the AEROMAT 80.
10 mm
4. Fix the rodding with timber or self-tapping countersunk screws (provided on-site).
The screw holes have the following dimensions:
Ø screw hole = 3.7 mm
Ø counterbore = 7.2 mm

10
AEROMAT 80 Assembly and operating instructions
08.2021
Technical specifications
Specifications for AEROMAT 80
Sound absorption (Rw1.9)40 dB 36 dB 33 dB 21 dB
Sound absorption in accordance with DIN EN ISO
20140-10 (Dn,e,w)47 dB 43 dB 40 dB 28 dB
Air throughput (approx.)
measured with 1,200 mm ventilator
length
2 Pa
4 Pa
5 Pa
7 Pa
8 Pa
10 Pa
20 Pa
7 m³/h
10 m³/h
11 m³/h
13 m³/h
14 m³/h
15 m³/h
23 m³/h
11 m³/h
16 m³/h
18 m³/h
21 m³/h
23 m³/h
26 m³/h
39 m³/h
13 m³/h
18 m³/h
21 m³/h
25 m³/h
26 m³/h
30 m³/h
42 m³/h
38 m³/h
56 m³/h
63 m³/h
76 m³/h
80 m³/h
90 m³/h
132 m³/h
U-value (calculated in accordance with ISO 6946) 1.9 W/m²K
Ventilator length (in mm increments) 300 - 3,000 mm
AEROMAT 80 Type D (without blower), with operating lever right or left (selectable)
Surface EV1 silver or RAL 9016 coated
Dimensions
18,5 mm
80 mm
76,5 mm
5 mm
18 mm
Ventilator length (operating lever, e.g. right)
*Stop profile (accessory for glazing rebate fitting)
*

Contact your dealer:
Head Office:
Industriestraße 1–3
57234 Wilnsdorf
GERMANY
Phone: [phone]
Telefax: [phone]
[e-mail]
www.siegenia.com
SIEGENIA worldwide:
Austria Phone: [phone]
Belarus Phone: [phone]
Benelux Phone: [phone]
China Phone: [phone]
France Phone: [phone]
Germany Phone: [phone]
Great Britain Phone: [phone]
Hungary Phone: [phone]
Italy Phone: [phone]
Poland Phone: [phone]
Russia Phone: [phone]
South Korea Phone: [phone]
Switzerland Phone: [phone]
Turkey Phone: [phone]
Ukraine Phone: [phone]
You can find address details for our
international sites at: www.siegenia.com
H47.FENS012EN/2