Siemens SIMATIC IPC MD-34A User manual

© Siemens AG 2023. All rights reserved
A5E52426055-AA, 05/2023 1
SIMATIC IPC MD-34A Battery Charger
Product Information
Package Content
Scope of delivery:
•Dual-bayBattery Charger × 1
•19V ACAdapter × 1
•Power Cord × 1
Design of product
Device in desk docking
Front view of battery charger
Interfaces
①Dual-bay Battery docking connector
④Dual-bay Battery Docking connector
②19V DC IN
⑤Buzzer
③LED Indicator
⑥Battery Cradle

SIMATIC IPC MD-34A Battery Charger
2A5E52426055-AA, 05/2023
LED Indicator Definition
LED Color
Definition
Solid Red
The battery charger is powered and ready for charging
Amber
Charging
Green
Battery capacity is higher than 95% full
Flashing Red
Charging Error
Buzzer Behavior
Sound
Behavior
Single Short Beep
Power input detected / Battery pack detected
Repeating Double
Beeps
Charging Error
Note
The default setting for built
-in buzzer is OFF.
To enable this feature or to adjust the volume of warning sound, refer to the switch at the bottom side of charging station.
Volume Switch
Graphic
Switch
Behavior
3, 4
Mute
1, 2
Maximum Volume
2, 4
Middle Volume
1, 3
Minimum Volume

SIMATIC IPC MD-34A Battery Charger
A5E52426055-AA, 05/2023 3
Powering the battery Charger
WARNING
To reduce the risk of electric shock or damage to your equipment:
•Plug the power cord into a grounded (earthed) outlet that is easily accessible at all times.
•Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
•Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
CAUTION
Always use the AC adapter that came with the Battery Docking
Perform the following steps:
1. Plug the power adapter with power cord to the battery charger.
2. The charging station beeps when the power input is detected (buzzer default off), and the LED indicator will be on in RED to
show the battery charger is ready to use.
Inserting the Battery Pack
Safety precautions
•Do not operate charger with damaged cord or plug. Have cord replaced immediately.
•Use proper adapters to connect battery charger to power outlet.
•Always unplug the charger if it is not being used.
•Do not expose charger to rain or snow.
•NEVER charge a frozen battery. If battery fluid (electrolyte) is frozen, bring into a warm area to thaw before charging.
•Be sure there is good ventilation in a room where the battery is being charged.
•Do not get the battery wet or immerse it in water.
•The battery should be charged at least every three months to avoid shortening the battery life.
•Do not squeeze or puncture the battery so as to avoid electrolyte leakage of lithium-ion battery.

SIMATIC IPC MD-34A Battery Charger
4A5E52426055-AA, 05/2023
Procedures
1. Put the battery connector down and align the battery edge to the sideway on charging slot. Insert the battery pack until the
battery connector is firmly connected to the charging pins.
2. The charging station beeps when the battery is well detected (buzzer default off). The LED in-dicator will then turn to AMBER
and the battery charger will start charging automatically.
Removing the Battery Pack
Perform the following steps:
1. The LED indicator turns to GREEN when the battery capacity is higher than 95% full.
2. The battery charger will stop charging when the battery packs are full charged.
3. Remove the battery pack directly.
SIMATIC IPC MD-34A Battery Charger
A5E52426055
-AA, 05/2023
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY