Siemens MMI User manual

Installation Instructions
Document No. 545-407
February 7, 2003
MMI Extension Cable
Item Number: 545-407-04, Rev. 010 Page 1 of 2
Product Description
The MMI Extension Cable (Figure 1) is an accessory
that allows you to connect a computer to an Open
Processor, Controller Module, or Gateway Module
and use the computer when the enclosure door is
closed or locked. The cable can be used with a
Modular Building Controller (MBC), Remote Building
Controller (RBC), or the Controller Board of a Floor
Level Network (FLN) Controller.
NOTE: See the following manuals for further
information about system installation and
programming constraints:
• Smoke Control Application and
Engineering Manual (125-1806)
• APOGEE Automation Technical
Reference on InfoLink
Product Numbers
545-712 MMI Extension Cable Assembly
(includes RJ-11 plug and RJ-11 jack)
Required Tools
• Flat-blade screwdriver
Figure 1. MMI Extension Cable.
Expected Installation Time
3 minutes
Prerequisites
• None
Installation
1. Use a screwdriver to tap on the MMI extension
cable knockout until it is removed.
See Figure 2 for an MBC/RBC enclosure, or
Figure 3 for an FLN Controller enclosure.
2. Insert the RJ-11 jack of the extension cable
(Figure 1) into the knockout and snap the jack
in place.
Figure 2. Installing an Extension Cable (MBC/RBC).
FLN0018R1
F
L
N
1
F
L
N
2
F
L
N
3
B
L
N
-
S
+-
S
+-
S
+-
S
+
12
VDC
RJ-11
PLUG
RJ-11
PLUG
KNOCKOUT
MMI
Modem
Port
MMI
Port
Controller Board
BPS (Bits per second)
BLN # Field Panel No./Name Memory
FLN1
FLN2
FLN3
MMI
Modem
MMI
BLN
WARNING:
Power must be ON
when replacing the
battery, otherwise
the cabinet will
coldstart.
TIU
Enabled
Product Part No. 545-793
Refer to Installation Instructions, Part No. 545-429
Adhere Bar Code Label in this space.
Underwriters Laboratories Inc.
®
LISTED
SMOKECONTROL SYSTEM EQUIPMENT SUBASSEMBLY.
Alsosuitable for use as:
ENERGYMANAGEMENT SUBASSEMBLY.
Alsosuitable for use as:
SIGNALSYSTEM UNIT SUBASSEMBLY.
Alsosuitable for use as:
PROCESSMANAGEMENT EQUIPMENT SUBASSEMBLY.
IssueNo.
Foruse with System 600 as part of an engineered
smokecontrol system in accordance with NFPA 92A.
C
¤¤
WARNING: Risk of static discharge.
Turn OFF power before removing or servicing
boards. Use ESD wrist strap when servicing unit.
Figure 3. Installing an Extension Cable
(FLN Controller).

Document No. 545-407
Installation Instructions
February 7, 2003
Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and
models as design improvements are introduced. Other product or company names mentioned herein may be the trademarks of their
respective owners. © 2003 Siemens Building Technologies, Inc.
Siemens Building Technologies, Inc.
1000 Deerfield Parkway
Buffalo Grove, IL 60089-4513
U.S.A.
Your feedback is important to us. If you have
comments about this document, please send
them to [e-mail]
Document No. 545-407
Printed in the U.S.A.
Page 2 of 2
MBC/RBC
Insert the RJ-11 plug of the extension cable
into the MMI port on the right side of the Open
Processor or Controller Module (Figure 4 and
Figure 5).
The installation is now complete.
Figure 4. MBC/RBC P2 MMI Ports
Open Processor or Controller Module.
Figure 5. MBC/RBC Stand-alone MMI Ports
Open Processor or Controller Module.
FLN Controller
Insert the RJ-11 plug of the extension cable
into the MMI port located on the right side of
the installed Controller Board (Figure 6).
The installation is now complete.
FLN0007R1
12
VDC
MMI
PORT
MMI
MODEM
PORT
POWER
SWITCH
ON 1
OFF 0
GROUNDING
SPADE
JP2
Figure 6. FLN Controller Board MMI Ports.