Siemens DMS8000 MP4 Series Operating and maintenance instructions

Building Technologies
Fire Safety & Security Products
DMS8000 MP4.xx
Geutebrück MultiScope DVR
Add-on module
Installation
Configuration

3
Building Technologies A6V10067796_a_en
Fire Safety & Security Products 30.06.2013
Table of Contents
1About this document .........................................................................................4
2Safety regulations..............................................................................................7
2.1 Country-specific standards...................................................................................7
2.2 Commissioning and testing..................................................................................7
2.3 Modifications to system design and products ......................................................7
3Introduction ........................................................................................................8
4Installation ..........................................................................................................9
4.1 Software installation.............................................................................................9
4.1.1 Software License ..................................................................................9
4.1.2 Installing the Add-on module..............................................................10
4.1.2.1 Multiple add-on’s installation...............................................................10
4.1.3 Removing the Add-on module............................................................10
5Configuration....................................................................................................11
5.1 Configuration checklist.......................................................................................11
5.2 Configuration procedure.....................................................................................11
6Technical Notes................................................................................................14
6.1 Limitations ..........................................................................................................14

About this document
1
4
Building Technologies A6V10067796_a_en
Fire Safety & Security Products 30.06.2013
1About this document
Purpose
This manual is intended as a guide to the to the installation and configuration for the
integration of Geutebrück Video systems in MM8000 management stations.
This guide is part of the general DMS8000 engineering documentation set which
includes the Composer Technical Manual, the other DMS8000 Connectivity Guides
(the complete list includes: Network, Fire, Intrusion, Access Control, Video, and OPC),
and the Installation, Configuration, and Commissioning manual (ICC) for each specific
product.
Scope
This document applies to the MM8000 Management Station MP4.15 and higher.
Target audience
This documentation is intended for the following users:
 Project Managers
 Project Engineers
 Commissioning Personnel
It is assumed that individuals performing the operations described in this manual have
prior expertise and training in the field of safety and security, at least a moderate level
of familiarity with the Siemens Building Technologies product line, and experience with
the installation, configuration, and commissioning of security management systems.
Documentation resource information
The DMS8000 Documentation Resource Information and Glossary Guide assembles
important information regarding documentation resources. This document contains the
following:
 Comprehensive definitions of the target audiences for Siemens FS DMS
documents
 Training program information including the Siemens intranet link
 A complete list of all available DMS8000 documents
 Instructions for how to obtain a document via the Siemens intranet using the
Siemens Asset Portal
 A map of relevant documents for each target audience group
 Customer Support links & resources
 A glossary containing definitions of all terms and acronyms used in DMS8000
documentation
To access the
DMS8000 Documentation Resource Information and Glossary Guide
(document no. A6V10089056), go to the link and follow the document search
instructions below:
http://assetportal.bt.siemens.com/portal/index.html
1. In the Search column on the left, set:
- Segment: 04 Fire -3F
- Document Type: All

About this document 1
5
Building Technologies A6V10067796_a_en
Fire Safety & Security Products 30.06.2013
- Image Type: All
- Advanced search criterias: Select Brochure No. and enter the document
number to search for (
A6V10089056 ). Alternatively, select Title and enter the
product name (
DMS8000 ).
2. Click Search to start.
3. In the resulting area on the right, click on Contents link to show the list of search
results.
For more information such as Siemens news and announcements, visit the STEP Web
portal at:
https://workspace.sbt.siemens.com/content/00001123/default.aspx
Operational and safety regulations
Before groups of persons begin work on the system, they must have read and
understood the Safety Regulations [➙ 7] section in this manual.
Liability disclaimer for damage or injuries
Before products are delivered, they are tested to ensure they function correctly when
used properly. Siemens disclaims all liability for damage or injuries caused by the
incorrect application of the instructions, or the disregard of danger advisories. This
disclaimer applies in particular to personal injuries or damage caused by:
 Improper and/or incorrect use.
 Disregard of safety instructions in the documentation or on the product.
 Poor maintenance or a lack of maintenance.
We have checked the contents of this manual for agreement with the hardware and
software described. Since deviations cannot be precluded entirely, we cannot
guarantee full agreement. However, the data in this manual are reviewed regularly and
any necessary corrections are included in subsequent editions. Suggestions for
improvement are welcome.
Copyrights and registered trademarks
Brand or product names mentioned in this document may be names protected by
copyright law or registered trademarks of other companies. These are mentioned only
for identification purposes and have no recommendatory character in regard to the
product or manufacturer, unless otherwise stated.
Documentation Conventions
The following table lists conventions to help you use this document in a quick and
efficient manner.
Convention Examples
Numbered Lists (1, 2, 3…) indicate a
procedure with sequential steps.
1. Turn OFF power to the field panel.
2. Disconnect the power cord.
3. Open the cabinet.
One-step procedures are indicated by a bullet
point.
 Expand the Event List.

About this document
1
6
Building Technologies A6V10067796_a_en
Fire Safety & Security Products 30.06.2013
Conditions that you must complete or must be
met before beginning a procedure are
designated with a ⊳.
Results, after completing a step or at the end
of the entire procedure, are designated with a
⇨.
⊳ The report you want to print is open.
1. Click the Print icon .
⇨ The Print dialog box appears.
2. Select the printer and click Print.
⇨ The print confirmation appears.
Bold font in a procedure indicates something
you should select or type.
Type F for Field panels.
Click OK to save changes and close the dialog
box.
Menu paths are indicated in bold. Select File > Text, Copy > Group, which
means from the File menu, then select Text,
Copy and finally Group.
Error and system messages are displayed in
Courier New font.
The message Definition successfully
renamed displays in the status bar.
Italics are used to emphasize a term. The Open Processor continuously executes a
user-defined set of instructions called the
control program .
This symbol signifies a Note. Notes provide
additional information or helpful hints.
Caution
This is a Caution message and indicates that
minor or moderate injury or property damage
may occur if a procedure is not followed.
Warning
This is a Warning message and indicates that
a serious injury or a severe equipment and
property damage may occur if a procedure is
not followed.
Cross references to other information in
printed material are indicated with an arrow
and the page number, enclosed in brackets:
[→92]
For more information on creating flowcharts,
see Flowcharts [→92].
Modification index
Note: For versions more than four years old, please visit the Siemens Asset Portal.
Version Date Notes
A6V10067792_a_en 06.2009 DMS8000 4.20.

Safety regulations
Country-specific standards 2
7
Building Technologies A6V10067796_a_en
Fire Safety & Security Products 30.06.2013
2Safety regulations
This section describes the danger levels and the relevant safety regulations applicable
to the use of the products described in this manual. Please read the following work
instructions as well as the preceding section
About this document thoroughly before
beginning any work.
2.1 Country-specific standards
Siemens products are developed and produced in compliance with the relevant
international and European safety standards. Should additional country-specific, and/or
local safety standards or regulations concerning project planning, installation, and/or
operation of the product(s) apply, then these standards and/or regulations must also be
taken into account, in addition to the safety regulations mentioned in the product
documentation.
2.2 Commissioning and testing
 Activate security-, fire- and third party systems or devices only in the presence of
the person responsible.
 Abide by the safety regulations of the connected sub-systems when working on
management stations. This especially applies when switching-off system
components.
 Inform people before the testing of alarm devices; take the possibility of panic
reactions into account.
 Inform the alarm and fault receiving stations connected to the system before
carrying out any tests.
2.3 Modifications to system design and products
Modifications to a system or to individual products may cause faults or
malfunctioning.
Please request written approval from Siemens Building Technologies, FS-DMS, and
the relevant authorities concerning intended system modifications and system
extensions.

Introduction
3 Modifications to system design and products
8
Building Technologies A6V10067796_a_en
Fire Safety & Security Products 30.06.2013
3Introduction
Geutebrueck Company provides video security solutions, including MultiScope (MSC)
DVR video recording systems that can be integrated in MM8000 management stations.
Geutebrück MultiScope (MSC) DVR
The Geutebrück MultiScope (MSC) is a family of Digital Video Recorders capable of
acquiring the video signals from 4, 8, 16 or 32 cameras, showing the images on a local
monitor, and storing them in digital form on local hard disks.
 Options are also available for video outputs and input/output management
 The host connection is based on a TCP/IP connection on a LAN network
Two basic MultiScope models and a total of 12 variants can be configured in the
MM8000 Video Network. Namely:
 MultiScope II Plus, handling 4, 8, 2x4 dual-speed, 16, 4x4 quad-speed, and 32
video inputs.
 MultiScope III, supporting 4, 8, 2x4 dual-speed, 16, 4x4 quad-speed, and 32 video
inputs.
MSC models and variants only differ on the number of cameras, and their configuration
in Composer is exactly the same (as illustrated in this section).
In the Geutebrück MultiScope DVRs, MM8000 only supports the video and monitoring
functions related to camera inputs.
In case of network-distributed solutions, be aware that DCOM security must be
configured in order to enable the correct communication over the network.
In general, the MM8000 internal user (see MM8000 Installation, Configuration, and
Commissioning manual) must be recognised by the server (i.e. defined locally on the
server computer or at domain level) and granted the DCOM permissions for the Video
server process (DCOMCNFG settings).
Also, the computer running MM8000 should be configured in order to grant access
the user of the video server.

Installation
Software installation 4
9
Building Technologies A6V10067796_a_en
Fire Safety & Security Products 30.06.2013
4Installation
The add-on package is provided in the MM8000 product DVD as add-on. It can be
installed using the standard Add-on Manager.
4.1 Software installation
4.1.1 Software License
MM8000 license must include specific items for the add-on, for the driver, and for the
required DVR units.
Therefore, the required license includes:
 WW8000 Composer (project configuration and download): Composer License or
Service key
 MM8000 core, no. of subsystems.
This license should include the number of DVR units.
 Add-on license
 Geutebrück driver license
Other licenses, covering more MM8000 options, may or may not be used and they are
not related to the add-on module support.

Installation
4 Software installation
10
Building Technologies A6V10067796_a_en
Fire Safety & Security Products 30.06.2013
4.1.2 Installing the Add-on module
The following are the installation procedures for the add-on module.
1. Start the Add-on Manager.
- From the Windows Start menu, select the following:
Start > DMS8000 > Tools > Add-on Manager
 The Add-on Manager window appears.
2. In the list of MM8000 Add-Ons/Name, select the name of the module you wish to
install
-- OR – (if the name of the add-on is not in the list on the screen):
click Browse, locate the installation files of the add-on module, and select the text
file (Extension Product Name.txt) in the root folder.
3. If your installation includes a customized MM8000 internal account , then deselect
the check box Use default MM8000 User account and specify the customized
username and password.
Note: For information about the MM8000 Internal Account, refer to MM8000
internal user account section of the MM8000 ICC, doc.no. A6V10062413_a_en.
4. Click Install (or Update if a previous version was detected).
4.1.2.1 Multiple add-on’s installation
In general, it is possible to install multiple add-on packages and benefit of their
combined functionalities. However, specific incompatibilities might exist. Please check
about possible problems in the documentation of all add-on modules that must be
installed.
4.1.3 Removing the Add-on module
Add-on module cannot be uninstalled.