Siemens SINUMERIK 840DE SL Quick start guide

SINUMERIK
SINUMERIK 840D sl
Basesoftware and operating
software
Commissioning Manual
Valid for
Control:
SINUMERIK 840D sl/840DE sl
Software:
CNC software V4.8 SP2
SINUMERIK Operate V4.8 SP2
12/2017
6FC5397-1DP40-6BA1
Preface
Fundamental safety
instructions 1
SINUMERIK Operate (IM9) 2
Easy XML 3
SINUMERIK Integrate
Access MyMachine / OPC UA 4
SINUMERIK Integrate Run
MyScreens (BE2) 5
NCU operating system 6
PCU base software (IM8) 7
PCU base software (IM10) 8
Appendix A

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: 6FC5397-1DP40-6BA1
Ⓟ 12/2017 Subject to change
Copyright © Siemens AG 2006 - 2017.
All rights reserved

Preface
SINUMERIK documentation
The SINUMERIK documentation is organized into the following categories:
● General documentation/catalogs
● User documentation
● Manufacturer/service documentation
Additional information
You can find information on the following topics at the following address (https://
support.industry.siemens.com/cs/de/en/view/108464614):
● Ordering documentation/overview of documentation
● Additional links to download documents
● Using documentation online (find and search in manuals/information)
If you have any questions regarding the technical documentation (e.g. suggestions,
corrections), please send an e-mail to the following address
(mailto:[email protected]).
mySupport/Documentation
At the following address (https://support.industry.siemens.com/My/ww/en/documentation),
you can find information on how to create your own individual documentation based on
Siemens' content, and adapt it for your own machine documentation.
Training
At the following address (http://www.siemens.com/sitrain), you can find information about
SITRAIN (Siemens training on products, systems and solutions for automation and drives).
FAQs
You can find Frequently Asked Questions in the Service&Support pages under Product
Support (https://support.industry.siemens.com/cs/de/en/ps/faq).
SINUMERIK
You can find information about SINUMERIK at the following address (http://www.siemens.com/
sinumerik).
Basesoftware and operating software
Commissioning Manual, 12/2017, 6FC5397-1DP40-6BA1 3

Target group
This documentation is intended for commissioning personnel.
The plant or system is readily assembled and wired. For the
following steps, e.g. configuring the individual components,
the Commissioning Manual contains all necessary information or at least references.
Benefits
The intended target group can use the Commissioning Manual to test and commission the
system or the plant correctly and safely.
Utilization phase: Setup and commissioning phase
Standard scope
This documentation only describes the functionality of the standard version. Additions or
revisions made by the machine manufacturer are documented by the machine manufacturer.
Other functions not described in this documentation might be executable in the control. This
does not, however, represent an obligation to supply such functions with a new control or when
servicing.
For the sake of simplicity, this documentation does not contain all detailed information about
all types of the product and cannot cover every conceivable case of installation, operation, or
maintenance.
Technical Support
Country-specific telephone numbers for technical support are provided in the Internet at the
following address (https://support.industry.siemens.com/sc/ww/en/sc/2090) in the "Contact"
area.
CompactFlash Cards
● Do not remove the memory card while it is being accessed. This can lead to damage of the
memory card and the SINUMERIK as well as the data on the memory card.
● Insert the memory card carefully and the right way round into the memory card slot (observe
indicators such as arrow or similar). This way you avoid mechanical damage to the memory
card or the device.
● Only use memory cards that have been approved by Siemens for use with SINUMERIK.
Even though SINUMERIK follows general industry standards for memory cards, it is
possible that memory cards from some manufacturers will not function perfectly in this
device or are not completely compatible with it (you can obtain information on compatibility
from the memory card manufacturer or supplier).
● For further information on handling CompactFlash cards, please refer to the NCU manuals.
Preface
Basesoftware and operating software
4Commissioning Manual, 12/2017, 6FC5397-1DP40-6BA1

Table of contents
Preface.........................................................................................................................................................3
1Fundamental safety instructions...................................................................................................................7
1.1 General safety instructions.......................................................................................................7
1.2 Equipment damage due to electric fields or electrostatic discharge......................................11
1.3 Warranty and liability for application examples......................................................................12
1.4 Industrial security...................................................................................................................13
1.5 Residual risks of power drive systems...................................................................................14
2 SINUMERIK Operate (IM9)........................................................................................................................15
3Easy XML.................................................................................................................................................719
4 SINUMERIK Integrate Access MyMachine / OPC UA..............................................................................917
5 SINUMERIK Integrate Run MyScreens (BE2)..........................................................................................987
6 NCU operating system...........................................................................................................................1319
7 PCU base software (IM8).......................................................................................................................1421
8 PCU base software (IM10).....................................................................................................................1559
A Appendix.................................................................................................................................................1733
A.1 Documentation overview SINUMERIK 840D sl..................................................................1733
Basesoftware and operating software
Commissioning Manual, 12/2017, 6FC5397-1DP40-6BA1 5

Table of contents
Basesoftware and operating software
6Commissioning Manual, 12/2017, 6FC5397-1DP40-6BA1

Fundamental safety instructions 1
1.1 General safety instructions
WARNING
Electric shock and danger to life due to other energy sources
Touching live components can result in death or severe injury.
● Only work on electrical devices when you are qualified for this job.
● Always observe the country-specific safety rules.
Generally, the following six steps apply when establishing safety:
1. Prepare for disconnection. Notify all those who will be affected by the procedure.
2. Isolate the drive system from the power supply and take measures to prevent it being
switched back on again.
3. Wait until the discharge time specified on the warning labels has elapsed.
4. Check that there is no voltage between any of the power connections, and between any
of the power connections and the protective conductor connection.
5. Check whether the existing auxiliary supply circuits are de-energized.
6. Ensure that the motors cannot move.
7. Identify all other dangerous energy sources, e.g. compressed air, hydraulic systems, or
water. Switch the energy sources to a safe state.
8. Check that the correct drive system is completely locked.
After you have completed the work, restore the operational readiness in the inverse sequence.
WARNING
Electric shock due to connection to an unsuitable power supply
When equipment is connected to an unsuitable power supply, exposed components may
carry a hazardous voltage that might result in serious injury or death.
● Only use power supplies that provide SELV (Safety Extra Low Voltage) or PELV-
(Protective Extra Low Voltage) output voltages for all connections and terminals of the
electronics modules.
Basesoftware and operating software
Commissioning Manual, 12/2017, 6FC5397-1DP40-6BA1 7

WARNING
Electric shock due to equipment damage
Improper handling may cause damage to equipment. For damaged devices, hazardous
voltages can be present at the enclosure or at exposed components; if touched, this can
result in death or severe injury.
● Ensure compliance with the limit values specified in the technical data during transport,
storage and operation.
● Do not use any damaged devices.
WARNING
Electric shock due to unconnected cable shields
Hazardous touch voltages can occur through capacitive cross-coupling due to unconnected
cable shields.
● As a minimum, connect cable shields and the cores of cables that are not used at one end
at the grounded housing potential.
WARNING
Electric shock if there is no ground connection
For missing or incorrectly implemented protective conductor connection for devices with
protection class I, high voltages can be present at open, exposed parts, which when touched,
can result in death or severe injury.
● Ground the device in compliance with the applicable regulations.
WARNING
Spread of fire from built-in devices
In the event of fire outbreak, the enclosures of built-in devices cannot prevent the escape of
fire and smoke. This can result in serious personal injury or property damage.
● Install built-in units in a suitable metal cabinet in such a way that personnel are protected
against fire and smoke, or take other appropriate measures to protect personnel.
● Ensure that smoke can only escape via controlled and monitored paths.
Fundamental safety instructions
1.1 General safety instructions
Basesoftware and operating software
8Commissioning Manual, 12/2017, 6FC5397-1DP40-6BA1

WARNING
Unexpected movement of machines caused by radio devices or mobile phones
When radio devices or mobile phones with a transmission power > 1 W are used in the
immediate vicinity of components, they may cause the equipment to malfunction.
Malfunctions may impair the functional safety of machines and can therefore put people in
danger or lead to property damage.
● If you come closer than around 2 m to such components, switch off any radios or mobile
phones.
● Use the "SIEMENS Industry Online Support App" only on equipment that has already been
switched off.
WARNING
Fire due to inadequate ventilation clearances
Inadequate ventilation clearances can cause overheating of components with subsequent
fire and smoke. This can cause severe injury or even death. This can also result in increased
downtime and reduced service lives for devices/systems.
● Ensure compliance with the specified minimum clearance as ventilation clearance for the
respective component.
WARNING
Unexpected movement of machines caused by inactive safety functions
Inactive or non-adapted safety functions can trigger unexpected machine movements that
may result in serious injury or death.
● Observe the information in the appropriate product documentation before commissioning.
● Carry out a safety inspection for functions relevant to safety on the entire system, including
all safety-related components.
● Ensure that the safety functions used in your drives and automation tasks are adjusted
and activated through appropriate parameterizing.
● Perform a function test.
● Only put your plant into live operation once you have guaranteed that the functions relevant
to safety are running correctly.
Note
Important safety notices for Safety Integrated functions
If you want to use Safety Integrated functions, you must observe the safety notices in the Safety
Integrated manuals.
Fundamental safety instructions
1.1 General safety instructions
Basesoftware and operating software
Commissioning Manual, 12/2017, 6FC5397-1DP40-6BA1 9

WARNING
Malfunctions of the machine as a result of incorrect or changed parameter settings
As a result of incorrect or changed parameterization, machines can malfunction, which in turn
can lead to injuries or death.
● Protect the parameterization (parameter assignments) against unauthorized access.
● Handle possible malfunctions by taking suitable measures, e.g. emergency stop or
emergency off.
Fundamental safety instructions
1.1 General safety instructions
Basesoftware and operating software
10 Commissioning Manual, 12/2017, 6FC5397-1DP40-6BA1