Siemens SSA911.01TH User manual

A6V11739247_en--_b Smart Infrastructure
2021-09-03
Smart valve actuator
SSA911.01TH
Wireless radiator valve actuator, works with RDS110.R
ƔRF-controlled actuator communication based on THREAD protocol (2.4 GHz,
bidirectional)
ƔConnection and operation with RDS110.R and optionally RCR114.1
ƔBattery-powered by commercially available 1.5 V AA batteries
ƔValve thread connection M30x1.5 mm
ƔNominal stroke 2.5 mm
ƔValve positioning force 90 N
ƔAutomatic adaptation to valve
ƔIntegrated temperature sensor and PI controller
Hindustan Hydraulics & Pneumatics, Chennai - 01.
Phone : [phone]
E-Mail : [e-mail]
Contact person : V. Anandha krishnan - 98409 21885

2
Siemens A6V11739247_en--_b
Smart Infrastructure 2021-09-03
Use
ƔThe SSA911.01TH wireless radiator valve actuator is designed to work on radiator
valves of different manufacturers in HVAC applications using M30x1.5 thread. It operates
the valve to control the water flow and controls the room temperature.
ƔThe valve actuator works only in combination with Siemens Smart Thermostat
RDS110.R and optionally with wireless repeater RCR114.1.
ƔOne RDS110.R can be paired with up to 6 radiator valve actuators in parallel. Up to 3
wireless repeaters RCR114.1 can be used to extend the range of the network.
Smart Thermostat
RDS (Application)
RDS110.R SSA911.01TH RCR114.1
RDS110.R
RCR114.1
SSA911.01TH
Topology with RDS110.R Topology with RCR114.1
Hindustan Hydraulics & Pneumatics, Chennai - 01.
Phone : [phone]
E-Mail : [e-mail]
Contact person : V. Anandha krishnan - 98409 21885

3
A6V11739247_en--_b Siemens
2021-09-03 Smart Infrastructure
Functions
Function Description
Communication The communication protocol used is THREAD.
THREAD is a low-power wireless mesh networking protocol and enables device-to-device
and device-to-cloud communication. THREAD is based on IEEE 802.15.4 radio standard.
Parallel operation Up to 6 actuators can be paired and operated with 1 RDS110.R or RCR114.1
Pairing The pairing process must be started on the Smart Thermostat and via HMI on the
SSA911.01TH
Calibration At first start-up, the SSA911.01TH automatically detects the end positions of the radiator
valve and calculates the available stroke. The actuator uses this information for positioning
between 0 and 100 %
Displaying status
information
Actuator status information is indicated on the display
ƔSetpoint temperature
ƔConnection to Smart Thermostat
ƔRadio signal strength
ƔBattery status (only active when the battery is low)
ƔError codes
Connection test When this function is activated, the actuator sends a signal to the connected Smart
Thermostat. Information about the actuator will be shown on the display of the Smart
Thermostat.
Reset and start
new pairing
The current connection to RDS110.R or RCR114.1 is deleted. A new pairing process to
connect to another Smart Thermostat device starts automatically.
Mechanical
adaptation to valve
This function starts a new calibration of the SSA911.01TH to the attached valve.
Factory reset Reset the actuator to factory settings. Any existing connection to RDS110.R or RCR114.1 is
deleted and the stem is retracted.
Firmware version Shows the running version of the firmware.
Back up mode In case of a loss of communication, the internal PI-controller controls the temperature
according to the last setpoint received from the Smart Thermostat using the internal
temperature sensor.
Low batteries When the battery capacity drops to 20 %, the actuator displays the battery symbol as a pre-
warning.
A command is sent to the Smart Thermostat and a low battery indication is shown on the
RDS110.R.
Once the batteries are empty, the actuator sends a signal to the Smart Thermostat controller
and shuts down operation with a minimum valve position of 15 %.
Error codes In case of an actuator malfunction or communication error with the Smart Thermostat, an
error code is shown on the display of the SSA911.01TH. See Error codes [ڰ9]
Type summary
Type Stock no. Description
SSA911.01TH S55181-A101 Smart radiator valve actuator
Scope of delivery
Every SSA911.01TH is supplied with 2 inserted AA alkaline batteries (LR6) and a Quick
guide (A5W00046617).
Hindustan Hydraulics & Pneumatics, Chennai - 01.
Phone : [phone]
E-Mail : [e-mail]
Contact person : V. Anandha krishnan - 98409 21885

4
Siemens A6V11739247_en--_b
Smart Infrastructure 2021-09-03
Accessories
Adapter AV.. for third-party valves
Type (= stock no.) For radiator valves from:
AV51 Beulco distributor M30x1.0
AV52 Comap
AV53 Danfoss RA-N (RA2000)
AV54 Danfoss RAVL
AV56 Giacomini
Theft protection kit
Type Stock no.
ATN5 S55845-Z244
The theft protection kit secures the actuator; it prevents the batteries from being removed
and the actuator from being unscrewed from the radiator valve without the use of a tool.
Equipment combinations
Siemens valves
The SSA911.01TH is suited for use with the following types of Siemens radiator valves:
Type kVS
[m3/h]
PN Data sheet
VDN1.., VEN1..
Radiator valves 0.25…1.41
10
CE1N2105
VDN2.., VEN2.., VUN2.. CE1N2106
VD1..CLC.. 1.9…2.6 CE1N2103
VPD.., VPE.. MCV radiator valves 0.02…0.48 CE1N2185
VD1.., VE1.. * Radiator valves 0.25…3.4 CE1N2145,
VD2.., VE2.., VU2.. * CE1N2146
For radiator valves with AV.. adapters, see Accessories [ڰ4]
kVS = Nominal flow rate of chilled water (5…30 °C) through the fully opened valve (H100) at a differential
pressure of 100 kPa (1 bar)
* No longer available
Hindustan Hydraulics & Pneumatics, Chennai - 01.
Phone : [phone]
E-Mail : [e-mail]
Contact person : V. Anandha krishnan - 98409 21885

5
A6V11739247_en--_b Siemens
2021-09-03 Smart Infrastructure
Third-party valves without adapter
The SSA911.01TH can operate third-party radiator valves without adapter, provided they
have a M30x1.5 mm connecting thread and meet the following requirements:
Force 90 N nominal
Fully closed x > 9.0 mm
Fully open y 14.5 mm
Valves of the following manufacturers may be used with the SSA911.01TH:
ƔHoneywell MNG
ƔCazzania
ƔHeimeier
ƔTA
ƔFinimetall
ƔOventop M30x1.5 (from 2001 onward)
ƔJunkers
ƔDanfoss
Valve pre-adjustment / kV-limitation
For valve pre-adjustments, refer to the relevant technical documentation on the valves.
Ensure a minimum valve stroke of > 0.5 mm.
Product documentation
Title Contents Document ID
Smart valve actuator
SSA911.01TH
Data sheet: product description A6V11739247
Quick guide Smart Valve
Actuator SSA911.01TH
Instructions for mounting, commissioning and
operating SSA911.01TH
A5W00046617
Mounting instructions Smart
Thermostat RDS110.R
Instructions for mounting RDS110.R A5W90008181
Quick guide Smart Thermostat
RDS110.R
Instructions for commissioning and operating
RDS110.R
A5W90008183
Smart Thermostat Wireless
RDS110.R
Data sheet: product description A6V11562461
RDS110.R Smart Thermostat
Wireless – User Guide
Detailed information on RDS110.R, including
installation, commissioning and operation
A6V11562455
Mounting instructions Smart
Thermostat Receiver RCR114.1
Instructions for mounting RCR114.1 A5W90008182
Quick guide Smart Thermostat
Receiver RCR114.1
Instructions for commissioning and operating
RDS110.R
A5W90008184
Smart Thermostat Receiver
RCR114.1
Data sheet: product description A6V11562464
Related documents such as environmental declarations, CE declarations, etc., can be
downloaded at the following Internet address:
http://siemens.com/bt/download
Hindustan Hydraulics & Pneumatics, Chennai - 01.
Phone : [phone]
E-Mail : [e-mail]
Contact person : V. Anandha krishnan - 98409 21885

6
Siemens A6V11739247_en--_b
Smart Infrastructure 2021-09-03
Notes
Security
CAUTION
National safety regulations
Failure to comply with national safety regulations may result in personal injury and property
damage.
ƔObserve national provisions and comply with the appropriate safety regulations.
WARNING
Burns from hot surface
The screw nut with which the actuator is fastened on the radiator valve will become hot.
Risk of burns from contact with the screw nut.
When servicing the actuator:
ƔSwitch off the radiator.
ƔAllow the radiator to cool off.
WARNING
Explosion due to fire or short circuit, even with discharged batteries
Risk of injury due to flying parts
ƔPrevent the batteries from coming into contact with water.
ƔDo not recharge batteries.
ƔDo not damage or disassemble batteries.
ƔDo not beat batteries over 85 °C.
WARNING
Leakage of electrolyte
Severe burns
ƔHandle damaged batteries only wearing suitable protective gloves.
ƔIn case of contact with electrolyte, rinse eyes immediately with plenty of water. Consult
a doctor.
Observe the following:
ƔObserve the polarities (+/-).
ƔThe batteries must be new and undamaged.
ƔDo not mix new and used batteries.
Store, transport and dispose of the batteries in compliance with local requirements,
regulations and laws. Also observe the instructions of the battery manufacturer.
Hindustan Hydraulics & Pneumatics, Chennai - 01.
Phone : [phone]
E-Mail : [e-mail]
Contact person : V. Anandha krishnan - 98409 21885

7
A6V11739247_en--_b Siemens
2021-09-03 Smart Infrastructure
Mounting
The SSA911.01TH is mounted on the radiator valve. There are no preferred mounting
positions; the actuator SSA911.01TH may be operated in all mounting positions. Make sure
the display is visible and the button is accessible.
WARNING
Falling objects
Overhead installation may result in injury from falling objects.
ƔDo not install the actuator more than 2 m above ground.
Firmly tighten the screw nut by hand. No tools are required to tighten the actuator on the
valve.
Commissioning
Install and commission the RDS110.R and (optionally) the RCR114.1
Choose the “Radiator valve” application on the Smart Thermostat (for documentation,
see Product documentation [ڰ5])
Start the installation and commissioning of the SSA911.01TH (see also Quick guide
A5W00046617)
1. Mechanical mounting of the SSA911.01TH on the radiator valve
– Tighten the threaded screw nut firmly by hand (do not use tools)
2. Remove plastic slip securing the batteries from the SSA911.01TH and wait for the
actuator to start up (approximately 5 s)
3. Press the button on the SSA911.01TH for automatic calibration process (> 2 s) and wait
for the confirmation of the calibration on the display
4. Start the pairing process on the RDS110.R in the advanced setting menu by pressing
“Pair new devices”
5. Press the button on the SSA911.01TH to start pairing (> 2 s). Pairing to Smart
Thermostat will take around 30 s.
ÖIf several devices are used in parallel, make sure only one device at a time is in
pairing mode. Otherwise, the pairing will not be successful.
ÖOnce the SSA911.01TH is paired to the RDS110.R, the display will confirm the con-
nection and switch off.
The SSA911.01TH is now controlled by the Smart Thermostat
Unsuccessful pairing or calibration to the valve is indicated by an error code on the display
(see Error codes [ڰ9]).
Hindustan Hydraulics & Pneumatics, Chennai - 01.
Phone : [phone]
E-Mail : [e-mail]
Contact person : V. Anandha krishnan - 98409 21885

8
Siemens A6V11739247_en--_b
Smart Infrastructure 2021-09-03
Operation
HMI
The interface consists of an LCD display [1] and one push
button [2].
During normal operation, the display is switched off in order
to conserve energy and ensure a long battery life.
Display Function Description
THREAD Communication Blinks during pairing mode with Smart Thermostat
Valve adaptation Shown during adaptation of the actuator to the radiator valve
Confirmation / acknowledgment Confirms a positive result after any successful operation
Low battery status Shown when status information feature is activated if the battery
is low
Connection test Shown for 30 s while a connection test is performed
The ID of the connected device will be shown on the RDS110.R
display
Key lock Shown when pressing the button if key lock mode is activated
In key lock mode, no manipulation on the actuator is possible.
Error Shown with error code when an error has occurred
Disappears when normal status has been reached again
Factory reset Shown during a factory reset process
Setpoint temperature
Temperature unit
Interactive symbols shown during pairing, adaptation and factory reset functions:
Ɣno: appears after choosing function
– short button press (< 1 s) exits the function, turns the display off and sends the actuator
to sleep mode
– long button press (> 2 s) confirms the chosen function
Ɣyes: appears after confirming the function (except during factory reset)
ƔGo: indicates the confirmed function is starting
Hindustan Hydraulics & Pneumatics, Chennai - 01.
Phone : [phone]
E-Mail : [e-mail]
Contact person : V. Anandha krishnan - 98409 21885

9
A6V11739247_en--_b Siemens
2021-09-03 Smart Infrastructure
Error codes
In case of an actuator malfunction or communication error with the Smart Thermostat, an
error code is shown on the display of the SSA911.01TH.
Error codes cannot be acknowledged on the SSA911.01TH. The error code is shown on the
display for as long as the error is active and will disappear once normal status has been
reached.
Error notifications are also sent to the Smart Thermostat and shown on the Smart
Thermostat display. E53 is at first only shown on SSA911.01TH and not immediately shown
on the Smart Thermostat. It will take some time to appear on the Smart Thermostat.
Code Error Cause Measures
Automatic
adaptation failed
ƔThe actuator did not correctly adapt to the valve
or could not detect the end positions of the valve
ƔThe actuator is not connected to a radiator valve
ƔCheck the valve type and stroke
compatibility with the SSA911.01TH and
repeat the adaptation
ƔCheck the mechanical valve connection,
adjust, and repeat the adaption
ƔEnsure that the valve is working correctly
and that the valve stem is not stuck and
repeat the adaptation
Mechanical valve
actuator error
ƔThe movement of the actuator was too short to
detect the end positions of the valve
ƔMotor movement failure
ƔThe actuator is not connected to a radiator valve
ƔThe stroke and/or end positions of the valve are
not compatible with the SSA911.01TH
No controller
found –pairing
failed
ƔNo RDS110.R or RCR114.1 is available to
connect
ƔThe Smart Thermostat is out of range
ƔRF chip failure
ƔCheck and adjust the settings on Smart
Thermostat and re-start the pairing
process
ƔDecrease the distance between the
SSA911.01TH and the Smart
Thermostat and re-start the pairing
process
Connection to
Smart Thermostat
lost
ƔThe current connection to the Smart Thermostat
is not available anymore (RF chip failure)
ƔThe paired RDS110.R or RCR114.1 is not
available anymore (e.g. loss of power)
ƔThe Smart Thermostat is out of range
ƔCheck the power supply and availability
of the Smart Thermostat
ƔDecrease the distance between the
SSA911.01TH and the Smart
Thermostat
No new pairing process is required
to resolve E53. The SSA911.01TH
will automatically re-
connect to the
Smart Thermostat once the
network is available again.
Hindustan Hydraulics & Pneumatics, Chennai - 01.
Phone : [phone]
E-Mail : [e-mail]
Contact person : V. Anandha krishnan - 98409 21885

10
Siemens A6V11739247_en--_b
Smart Infrastructure 2021-09-03
Maintenance
The SSA911.01TH is maintenance free.
The actuator and the Smart Thermostat will indicate when replacing the batteries is required
approximately 2 months before the batteries are completely empty and the actuator switches
off.
Disassembly
NOTICE
Dismounting the Smart Valve Actuator
Dismounting the SSA911.01TH while the stem is extended puts the actuator in an unde-
fined state that makes re-mounting the actuator without damaging it very difficult.
ƔBefore dismounting the SSA911.01TH from the valve, always perform either a new me-
chanical adaptation to the radiator valve or a factory reset to retract the stem.
- Mechanical adaptation to valve: keep the button pressed 9…12 s.
- Factory reset: Keep the button pressed for 12…16 s.
Replacing the batteries
To replace the batteries, the SSA911.01TH should remain mounted on the radiator valve
and the Smart Thermostat should remain on power and switched on.
If it is necessary to remove the actuator from the valve, a factory reset or new adaptation
must first be performed (see above, Disassembly [
ུ
10]).
Replacing the batteries does not require any tools. For optimal performance, the use of high
performance alkaline batteries is recommended.
1. Remove the batteries
– Open the white battery cover [1]
– Remove the metallic slider [2]
– Take the batteries out [3]
Hindustan Hydraulics & Pneumatics, Chennai - 01.
Phone : [phone]
E-Mail : [e-mail]
Contact person : V. Anandha krishnan - 98409 21885