Siemens SSE161.05U User manual

Electromotoric actuator
SSE161.05U, SSF161.05U
For 2-way & 3-way 599 Series Zone Valves
●Operating voltage AC/DC 24 V, positioning signal DC 0...10 V
●Self-calibrating to the valve stroke
●Direct mounting with coupling nut, no tools required
●Manual override
●Position and actuator motion indication (LED)
●Positioning force 45 lbf (200 N)
●Parallel operation of multiple actuators possible
●3-pin terminal block
A6V12681514_enUS_b
Smart Infrastructure
06/15/2023

2
Siemens
A6V12681514_enUS_b
Smart Infrastructure
06/15/2023
Use
●For 2-way & 3-way 599 Series Zone Valves: 599-00210 - 599-00214, 599-00230 - 599-
00234, 599-00510 - 599-00514, 599-00530 - 599-00534
●Typically in chilled ceiling, VAV and fan coil unit applications
●Max.10 units of SSE161.05U, SSF161.05U can operate in parallel, provided the
controller output suffices.
Technical design
When the actuator is driven by DC 0…10 V positioning signal, it produces a stroke, which is
transmitted to the valve stem.
DC 0...10 V control signal
●The valve opens / closes in proportion to the
control signal at Y.
●At DC 0 V, the SSE161.05U actuator stem is
extended, and the normally open valve is fully
closed.
●At DC 0 V, the SSF161.05U actuator stem is
retracted and the normally open valve is fully open.
●When no power is supplied, the actuator maintains
its current position.
Y = Control signal Y [V]
H = Percentage of calibrated valve stroke
LED indication
Status
LED indication patterns
Variants
SSE161.05U, SSF161.05U
Modulation: Stem retracting
Flashing green in sequence: LED1-->LED2-->LED3 (500 ms each)
Modulation: Stem extending
Flashing green in sequence: LED3-->LED2-->LED1 (500 ms each)
Stem position
At H0 (fully extended for SSE and fully retracted for SSF) - H40:
Constant green (LED3)
At H40 - H60: Constant green (LED2)
At H60 - H100 (fully retracted for SSE and fully extended for SSF):
Constant green (LED1)
Calibration
Flashing green (LED2): 100 ms on, 100 ms off
Error
Constant red (LED2)
Manual operation
Flashing green/red alternatively (LED2): Green 500 ms, red 500 ms

3
Siemens
A6V12681514_enUS_b
Smart Infrastructure
06/15/2023
Type summary
Type
Stock number
Operating
voltage
Running
speed
Running time
2.5 mm
Control signal
Actuator
characteristic
SSE161.05U
S55180-A157
AC/DC 24 V
5 s/mm
12.5 s ±25 %
DC 0...10 V
Linear
SSF161.05U
S55180-A158
AC/DC 24 V
5 s/mm
12.5 s ±25 %
DC 0...10 V
Linear
Ordering
When ordering, specify both type and quantity.
Example:
Type
Stock number
Designation
Quantity
SSE161.05U
S55180-A157
Electromotoric actuator
2
Delivery
Valves and actuators can be ordered assembled in the factory or ordered separately. For
easier valve assembly, actuators ordered separately have the actuator stem fully retracted.
Equipment combinations
Valves
Combinable valves for SSE161.05U and SSF161.05U - 2-way & 3-way 599 Series Zone
Valve
Nominal Line Size
Flow Rate
Connection
Inch
mm
Cv
Kvs
NPT
Sweat
2-Way
0.5
15
1.0
(0.85)
599-00210
599-00510
0.5
15
2.5
(2.15)
599-00211
599-00511
0.5
15
4.0
(3.4)
599-00214
599-00514
0.75
20
4.1
(3.5)
599-00212
599-00512
1
25
7.0
(6.0)
599-00213
599-00513
3-Way
0.5
15
1.0
(0.85)
599-00230
599-00530
0.5
15
2.5
(2.15)
599-00231
599-00531
0.5
15
4.0
(3.4)
599-00234
599-00534
0.75
20
4.1
(3.5)
599-00232
599-00532
1
25
7.0
(6.0)
599-00233
599-00533

4
Siemens
A6V12681514_enUS_b
Smart Infrastructure
06/15/2023
Note: To ensure trouble-free operation of
third-party valves with the SSE/SSF..
actuators, the valves must satisfy the
following requirements:
●Threaded connections with coupling nut
M30 ×1.5.
●Nominal force F ≤ 45 lbf (200 N)
●Dimension X ≥ 0.33 in (8.3 mm)
●Dimension Y ≤ 0.58 in (14.8 mm)
Product documentation
Topic
Title
Document ID
Installation
Mounting instruction
A6V13122037
Standards and directives
CE declarations
A5W00254962A
RCM conformity
A5W00254983A
Environmental compatibility
Environmental declarations
A5W00242127A
Related documents such as the environmental declarations, declarations of conformity, etc.,
can be downloaded from the following Internet address:
www.siemens.com/bt/download
Notes
Engineering
The actuators must be electrically connected in accordance with local regulations (see
"Connection diagrams”).
CAUTION
National safety regulations
Failure to comply with national safety regulations may result in personal injury and property
damage.
●Observe national provisions and comply with the appropriate safety regulations.
Observe permissible temperatures (see "Technical data [▶8]").
Mounting
WARNING
●Do not use pipe wrenches, pliers or similar tools.
●Avoid lateral pressure or (cable) tension on the mounted actuator!
Valve and actuator are easy to assemble on site before commissioning:
●Remove protective cover from the valve body.
●Position the actuator and tighten the union nut manually.
●See "Mounting instruction" for graphical instructions.

5
Siemens
A6V12681514_enUS_b
Smart Infrastructure
06/15/2023
Orientation
Commissioning
When commissioning, check both wiring and functioning of the actuator.
●Actuator stem extends
Normally open valve closes, normally closed
valve opens
●Actuator stem retracts
Normally open valve opens, normally closed
valve closes
NOTICE
The actuator must be commissioned only with a correctly mounted valve in place!
Self-calibration
When operating voltage is applied, the actuator self-calibrates (fully retracted ➙fully
extended ➙setpoint).
CAUTION
Never intervene manually during self-calibration.
NOTICE
●Correct calibration is only possible with valve stroke > 0.05 inch (1.2 mm). Valve stroke
< 1.2 mm results in calibration failure.
●If calibration fails, the actuator performs another calibration automatically after
10 seconds.
●After three failed calibration attempts, the actuator stem remains in the extended
position and the valves are open.
Manual operation
A 3-mm hexagonal wrench can be used to move the actuator to any position.
Power
On
Calibration Y
t
Fully retracted
Fully extended

6
Siemens
A6V12681514_enUS_b
Smart Infrastructure
06/15/2023
To move the actuator stem manually
1. Open the cover using a proper screwdriver.
2. Press and hold down button (a) illustrated below for at least three seconds.
–The actuator ignores any control signal from the controller.
3. Adjust the position of the actuator stem by rotating hexagonal wrench (b) illustrated
below clockwise or counter-clockwise.
–The actuator stem moves down if you rotate clockwise; it moves up if you rotate
counter-clockwise. The manually set position is retained.
4. To exit manual operation mode, press and hold down button (a) illustrated below again
for at least three seconds.
–The actuator runs a self-calibration automatically. Control signal sent from the
controller takes effect.
5. Close the cover.
NOTICE
If operating voltage is applied to actuator, press button (a) before and after manually
adjusting the position of the actuator stem. If no operating voltage and control signal are
applied, manual operation can be done without pressing button (a).
Cabling operation
1. Unscrew cover screw
2. Remove cover
3. Connect or disconnect wire terminals (terminal block is removable)
4. Install the cover
5. Screw in the cover screw
A6V11858278Z10
3 mm
(b)
(a)
> 3s

7
Siemens
A6V12681514_enUS_b
Smart Infrastructure
06/15/2023
Maintenance
The actuators require no maintenance.
WARNING
Operating voltage must be switched off during any maintenance!
NOTICE
When carrying out service work on the plant, note the following:
●Switch off operating voltage.
●If necessary, disconnect electrical connections from the terminals.
●The actuator must be commissioned only with a correctly mounted valve in place!
Repair
The actuators cannot be repaired; the complete unit must be replaced.
Disposal
The device is considered an electronic
device for disposal and may not be disposed
of as domestic waste.
●Dispose of the device through channels
provided for this purpose.
●Comply with all local and currently
applicable laws and regulations.
Warranty
Technical data on specific applications are valid only together with Siemens products listed
under "Equipment combinations". Siemens rejects any and all warranties in the event that
third-party products are used.
Open Source Software (OSS)
Software license overview
These devices use Open Source Software (OSS). All Open Source Software components
used in the product (to include copyrights and licensing agreement) are available at
http://siemens.com/bt/download.
Firmware version
OSS document
Device
Document ID
Title
2.10.0 or above
A6V13503690
Readme OSS for Modulating Room Actuator 200 N, 300 N
All

8
Siemens
A6V12681514_enUS_b
Smart Infrastructure
06/15/2023
Technical data
Power supply
Operating voltage
AC 24 V (±15 %) or DC 24 V (±20 %)
Frequency
50/60 Hz
Power consumption
3 VA (AC); 1.2 W (DC)
Primary fuse or breaker rating
External, 2 A quick blow
Signal input
Control signal
DC 0…10 V
Input impedance
100 kOhm
Parallel operation (number of actuators)
Max. 101)
1) Provided that the controller output is sufficient.
Operating data
Position with de-energized contact Y
See "Technical design [▶2]"
Running speed (time for 2.5 mm)
< 5 s/mm ±25 % (12.5 s ± 25 %)
Positioning force
45 lbf (200 N)
Stroke
0.05 to 0.25 inch (1.2…6.5 mm)
Permissible temperature of medium in the connected
valve
34 to 248°F (1…120℃)
Electrical connection
Permissible length for signal lines
65 ft (20 m)
Wire cross section
18...20 AWG (0.5...0.75 mm²）
Cable diameter
<0.2 inch （5 mm）
Mounting
Connection to valve
Plastic coupling nut M30 × 1.5
Orientation
Above horizontal
Standards
EU conformity declaration (CE)
A5W00254962A
RCM conformity declaration
A5W00254983A
UK conformity declaration (UKCA)
A5W00257055A
Housing protection degree
NEMA 2 / IP20 (EN 60529)
Protection class according to EN 60730
III

9
Siemens
A6V12681514_enUS_b
Smart Infrastructure
06/15/2023
Standards
Pollution degree
2
Overvoltage category
I
Environmental compatibility
The product environmental declaration
(A5W00242127A) contains data on environmentally
compatible product design and assessments (RoHS
compliance, materials composition, packaging,
environmental benefit, disposal).
UL Approval
Federal Communications Commission
UL as per UL60730-1, UL60730-2-14
http://ul.com/database
cUL as per CSA –CAN E60730-1, E730-2-14
FCC CFR 47 Part 15 Class B
ICES003
CAN ICES-3 (B)/NMB-3(B)
FCC regulations
Modification of this device to receive cellular radio telephone service signals is pro-
hibited under FCC rules and federal law.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Housing color
Cover/base
2003, Ti-Gray
Coupling nut
RAL 9017
General ambient conditions
Operation
Transport
Storage
Temperature
34 to 122°F (1…50 ℃)
-13 to 158°F (-25…70 ℃)
-13 to 158°F (-25…70 ℃)
Humidity
5…95 % r.h.
non condensing
< 95 % r.h.
non condensing
5…95 % r.h.
non condensing
Atmospheric
pressure
Min. 700 hPa, corresponding to
max. 3,000 m above sea level
-
-

10
Siemens
A6V12681514_enUS_b
Smart Infrastructure
06/15/2023
Material
Cover/base
PC + ABS
Weight
SSE161.05U
7.7 ounces (217 g)
SSF161.05U
7.6 ounces (216 g)