Siemens SIMATIC Industrial Flat Panel IFP2200 Administrator guide

IFP2200 INOX MT ETH
SIMATIC
HMI devices
IFP2200 INOX MT ETH
Compact Operating Instructions
Translation of the original instructions
07/2021
A5E42185570
-AD
Preface
Overview
1
Safety instructions and
further information
2
Installing and connecting
the device
3
Maintenance and care
4
Technical specifications
5
Technical Support
A
List of abbreviations
B

Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E42185570-AD
Ⓟ
07/2021 Subject to change
Copyright © Siemens AG 2021.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

IFP2200 INOX MT ETH
Compact Operating Instructions, 07/2021, A5E42185570-AD 3
Preface
Scope of validity
These compact operating instructions apply to the following INOX device:
•SIMATIC IFP2200 INOX MT ETH, article number 6AV7485-6BE00-0AA0
The INOX device is based on the following standard device:
•SIMATIC IFP2200, article number 6AV7863-4MA20-0AA0
With regard to electronics and interfaces, the device is based on the Ethernet monitor
IFP2200 ETH with capacitive multi-touch screen and corresponding functionality. You can
find a description of the IFP2200 ETH in the operating instructions "Industrial Flat Panel
IFP1500, IFP1900, IFP2200, IFP1900 PRO, IFP1900 ETH, IFP2200 ETH
(http://support.automation.siemens.com/WW/view/en/65288650)", on which these compact
operating instructions are based.
The compact operating instructions provided here describe the technical differences as
compared to the IFP2200 ETH standard device.
Unless otherwise described in this document, all specifications in the underlying operating
instructions for IFP2200 ETH, which means specifications regarding hardware, software,
maintenance and service, apply to this device.
However, the information in these compact operating instructions take precedence over
statements in the underlying operating instructions, in the release notes and in the online
help.
Note
This document belongs to the devi
ce and will also be required for repeat commissioning.
Keep all supplied and supplementary documentation for the entire service life of the device.
Pass on all of these documents to a future owner of the device.

Preface
IFP2200 INOX MT ETH
4Compact Operating Instructions, 07/2021, A5E42185570-AD
Style conventions
Style Convention
Scope
"Add screen"
•Terms that occur in the user interface, for example, dialog name, tab,
button, menu command
•Necessary entries, for example, limit value, tag value
•
Path specification
"File > Edit"
Operating sequences, for example, menu item, shortcut menu command
<F1>, <Alt+P>
Designation of a key on a keyboard
You should also observe notes that are marked as follows:
Note
A note contains important information about the product
described in the document and its
handling, or a specific section of the document to which you should pay particular attention.
Naming conventions
Term
Applies to
System
•System
•Machining center
•One or more machines
Device, built-in device,
Ethernet monitor
•SIMATIC IFP2200 INOX MT ETH
MT
Multitouch
ETH
Ethernet monitor
Touch HMI device
Device with capacitive multi-touch screen
Touch screen
Multi-touch screen
Touch operation
Multitouch
Figures
This document contains illustrations of the described devices. The figures can deviate from
the particularities of the delivered device.

IFP2200 INOX MT ETH
Compact Operating Instructions, 07/2021, A5E42185570-AD 5
Table of contents
Preface ................................................................................................................................................... 3
1 Overview................................................................................................................................................ 7
1.1 Product overview................................................................................................................. 7
1.2 Scope of delivery ................................................................................................................. 8
1.3 Device configuration............................................................................................................ 8
1.4 Interfaces ............................................................................................................................ 9
1.5 Accessories.......................................................................................................................... 9
2 Safety instructions and further information ....................................................................................... 10
2.1 Intended use ..................................................................................................................... 10
2.2 General safety instructions................................................................................................. 10
2.3 Operating the capacitive multi-touch screen....................................................................... 12
2.4 Notes about usage............................................................................................................. 14
2.5 Use in hazardous areas ...................................................................................................... 16
3 Installing and connecting the device .................................................................................................. 17
3.1 Preparing for installation.................................................................................................... 17
3.1.1 Check the scope of delivery................................................................................................ 17
3.1.2 Checking the operating conditions..................................................................................... 17
3.1.3 Permitted mounting positions............................................................................................ 17
3.1.4 Notes on installation.......................................................................................................... 19
3.1.5 Checking clearances .......................................................................................................... 19
3.2 Inserting the mounting seal ............................................................................................... 20
3.3 Mounting the device.......................................................................................................... 22
3.4 Connecting the device ....................................................................................................... 25
3.4.1 Securing the cables............................................................................................................ 25
3.4.2 Securing cables for use in hazardous areas ......................................................................... 26
4 Maintenance and care ......................................................................................................................... 27
4.1 Cleaning and maintenance ................................................................................................ 27
4.2 Working with pressure washers.......................................................................................... 29
4.3 Working with stainless steel surfaces.................................................................................. 30
4.4 Clean screen for Touch HMI devices ................................................................................... 31
4.5 Chemical Resistance .......................................................................................................... 31
4.6 Calibrate touch screen ....................................................................................................... 32
4.7 Recycling and disposal ....................................................................................................... 32

Table of contents
IFP2200 INOX MT ETH
6Compact Operating Instructions, 07/2021, A5E42185570-AD
5 Technical specifications....................................................................................................................... 33
5.1 Software license agreements ............................................................................................. 33
5.2 Certificates and approvals .................................................................................................. 33
5.3 Dimension drawings .......................................................................................................... 36
5.3.1 Dimension drawing 22" device........................................................................................... 36
5.3.2 Dimension drawing 22" clamping frame............................................................................. 37
5.4 Rating plate ....................................................................................................................... 37
5.5 Technical specifications ..................................................................................................... 38
5.6 Ambient conditions ........................................................................................................... 39
5.6.1 Transport and storage conditions ....................................................................................... 39
5.6.2 Operating conditions ......................................................................................................... 40
5.6.3 Electromagnetic compatibility............................................................................................ 41
5.6.4 Information on insulation tests, protection class and degree of protection.......................... 43
A Technical Support................................................................................................................................ 44
A.1 Service and support ........................................................................................................... 44
B List of abbreviations ............................................................................................................................ 45
Index.................................................................................................................................................... 46

IFP2200 INOX MT ETH
Compact Operating Instructions, 07/2021, A5E42185570-AD 7
Overview
1
1.1 Product overview
The SIMATIC INOX HMI devices with touch screen and glass front are designed for use in the
food and beverage industry and the pharmaceutical industry.
Features
•Scratch-resistant glass surface with hardness 6 on the Mohs hardness scale
•Resistant glass and sturdy stainless steel front with minimized grooves and crevices
•Optimized frame design with minimized protrusions to the control cabinet and for
automatic runoff of liquids
•Stainless steel surface polished with grain size 240
•Degree of protection, front: IP66K 1, IP69 1 (IP69 is comparable to IP69K)
•Hardened glass with impact resistance IK08
•Chemical resistance to cleaning agents and disinfectants as described in section "Chemical
Resistance (Page 31)".
•Replaceable, food-grade built-in seal
•Rear clamping frame for even application pressure of the mounting gasket
•Mounting cutout, interfaces and functionality correspond to those of the standard device.
1For use in hazardous areas of Zones 2 and 22: on the front at least IP65, see section
"Information on insulation tests, protection class and degree of protection (Page 43)".

Overview
1.2 Scope of delivery
IFP2200 INOX MT ETH
8Compact Operating Instructions, 07/2021, A5E42185570-AD
1.2 Scope of delivery
The scope of delivery includes:
•1 × device
•1 × accessory pack with the following contents:
–1 mounting gasket
–1 clamping frame
–1 power supply connector
–Mounting clips (see section "Mounting the device (Page 22)")
•Product information, mounting instructions
•Product information (approvals, explosion protection)
1.3 Device configuration
Front and side view
①
Recesses for one mounting clip each
②
Display with touch screen

Overview
1.4 Interfaces
IFP2200 INOX MT ETH
Compact Operating Instructions, 07/2021, A5E42185570-AD 9
1.4 Interfaces
①
X80
Connection for 24 V DC power supply
②
X1
Ethernet interface
③
Reset button
④
X70
DisplayPort port
⑤
X61/X62
USB Type A
⑥
X60
USB Type B
1.5 Accessories
Accessories can be ordered on the Internet at:Expansion components and accessories
(http://www.automation.siemens.com/mcms/pc-based-automation/en/industrial-
pc/expansion_components_accessories)
•For the replacement of the built-in seal or as spare parts for mounting hardware:
Service pack, article number 6AV7675-4JE20-0AA0
•Fasteners:
"Die-cast aluminum" mounting clips, article number 6AV2185-8MA00-0AA0.
See also
Inserting the mounting seal (Page 20)
Mounting the device (Page 22)

IFP2200 INOX MT ETH
10 Compact Operating Instructions, 07/2021, A5E42185570-AD
Safety instructions and further information
2
The general safety instructions in the "SIMATIC HMI Industrial Flat Panels IFP, IFP PRO, IFP
ETH" operating instructions apply to all devices with a capacitive multi-touch screen and
Ethernet monitors.
2.1 Intended use
The SIMATIC INOX HMI device with glass front is designed to be used for high-performance
visualization tasks (operator control and monitoring) and in ambient conditions such as those
found in the food, beverage, and pharmaceutical industries.
The devices are generally designed for use in open processes (according to DIN EN 1672-2)
and are primarily intended for use in splash zones. In addition, the touch HMI devices can be
used for indirect contact with acidic, alcoholic or dry food. Indirect contact means alternating
contact of the device and food in the process by the operating personnel.
Any use that deviates from this intended use is prohibited. Also see the information in the
section "Cleaning and maintenance (Page 27)".
Particular attention has been paid during design of the HMI devices to ensure that the front
panel is easy to clean and can be disinfected when needed. The devices with stainless steel
front have therefore been developed according to DIN EN 1672-2 "Food Processing
Machinery - Safety and Hygiene Requirements".
2.2 General safety instructions
Installation according to the instructions
WARNING
The device may only be used in machines which comply with the Machinery Directive
The "Machinery Directive" governs, among other things, the precautions to be taken when
commissioning and operating machines within the European Economic Area.
Failure to follow these precautions is a breach of the Machinery Directive. Such failure may
also cause personal injury and damage depending on the machine operated.
The machine in which the HMI device is to be operated must conform to Directive
2006/42/EC.

Safety instructions and further information
2.2 General safety instructions
IFP2200 INOX MT ETH
Compact Operating Instructions, 07/2021, A5E42185570-AD 11
Open equipment and control cabinet
WARNING
The device constitutes open equipment on the back side
The device constitutes open equipment on the back side. This means that you must
integrate the device in an enclosure or cabinet where the device is operated via its front
side. The enclosure, the cabinet or the electrical operating rooms must provide protection
against electric shock and the spread of fire. The requirements regarding the mechanical
strength must also be considered.
Access to the enclosure or cabinet in which the device is installed should only be possible by
means of a key or tool and for trained and qualified personnel.
Electrocution risk when control cabinet is open
When you open the control cabinet, there may be a dangerous voltage at certain areas or
components.
Touching these areas or components can cause electrocution.
Always disconnect the cabinet from the mains before opening it.
Observe the safety and accident prevention instructions applicable to your application in
addition to the safety instructions given in the device documentation.
Notes on the touch screen
WARNING
Danger of explosion in hazardous areas, personal injury or property damage due to
defective touch screen
Massive force applied to the front panel is not an intended use of the device and can destroy
its touch screen, e.g. break the glass front. In hazardous areas, there is then a risk of
explosion, injury and food contamination with further consequential and health damages.
Make sure that excessive force cannot be applied to the front panel.
If the touch screen of the device is defective, follow these steps:
•Stop production.
•Immediately shut down the affected machine and label it accordingly.
•Handle any potentially contaminated product in accordance with legal regulations.
•Replace the device immediately. When replacing the device, please note the section
"Installing and connecting the device (Page 17)".
•
Clean the machine before putting it back into operation.
ESD
Electrostatically sensitive components include almost all electrical, electronic, optoelectronic
and electromechanical components. These components are sensitive to overvoltage for
technical reasons and their function may be impaired or destroyed by electrostatic discharge.
Observe the regulations governing the handling of ESD components.

Safety instructions and further information
2.3 Operating the capacitive multi-touch screen
IFP2200 INOX MT ETH
12 Compact Operating Instructions, 07/2021, A5E42185570-AD
Pulse-shaped interference
IFP2200 MT devices have been tested for high-energy single pulses (surge) in accordance
with IEC 61000-4-5.
An external protective circuit is required for operation with 24 V DC; see function manual
"SIMATIC S7-1500, ET 200MP, ET 200SP, ET 200AL Designing interference-free controllers",
section 7 "Lightning protection and overvoltage protection", which is available on the Internet
(https://support.industry.siemens.com/cs/ww/en/view/59193566).
The following lightning protection element was used during the testing of the Industrial Flat
Panel:
Dehn BVT AVD 24" (Order No. 918 422)
2.3 Operating the capacitive multi-touch screen
You operate the multi-touch screen with one or multiple fingers. You can also operate it
using gestures with up to five fingers at a time.
WARNING
Personal injury or property damage due to no earth connection
An inadequate earth connection or the lack of one may cause malfunction of the capacitive
touch screen. Functions may not work properly. This can result in personal injury or property
damage.
•Always connect the device to an earth conductor.
•The earth conductor from the device must be connected directly to earth with low
impedance (short connection, minimum cross-section 2.5 mm
2
).
WARNING
Personal injury or property damage due to maloperation
Incorrect operation of devices with a touch screen can occur. This can result in personal
injury or property damage.
Take the following precautions:
•Configure the plant so that safety-related functions are not operated with the touch
screen.
•
Switch off the device for cleaning and maintenance.

Safety instructions and further information
2.3 Operating the capacitive multi-touch screen
IFP2200 INOX MT ETH
Compact Operating Instructions, 07/2021, A5E42185570-AD 13
WARNING
Danger of malfunction due to improper execution of gestures on the touch screen
If gestures are executed incorrectly on the touch screen with multi-touch function, these
gestures may not be recognized or could be recognized incorrectly. The entries made are
then not implemented by the device or are implemented incorrectly or in an unintended
manner.
Incorrect execution of multi-touch functions can lead to errors in the operation of the plant
and thus to physical injury.
Note the following when operating the touch screen with multi-touch function:
•The touch screen reacts to contact on its surface, not to pressure.
•When using a touch pen: Operate the touch screen only with a touch pen for capacitive
touch.
•Avoid unintended multiple touches, for example, with your knuckles.
Before you start to operate the device, make sure you are familiar with the multi-touch
functions of the Windows operating system, as well as with the application to be used and
its functions. Ensure that the gestures which the user executes on the multi-touch display
are recognized by the application. It is possible that certain gestures need to be trained
beforehand.
Notes on operation
Note
Do not touch the
touch screen during startup
The device automatically calibrates the capacitive multi
-touch screen during startup. The
touch screen is locked during calibration.
Do
not touch the touch screen during startup. Make sure that you do not rest on the touch
scree
n with the palm of your hand during startup.
Make sure that there are no conductive liquids on the touch screen during startup.
Note when operating the multi-touch screen:
•Surface contact with a diameter of about 5 to 20 mm is required for an operator action to
be detected.
•An operation with gloves with a material thickness of <2 mm is detected in most cases.
However, check the usefulness of the gloves you are using.
•To avoid incorrect operation, certain inputs are ignored and blocked from further entry:
–Simultaneous operation with more than 5 fingers.
–Surface contact with a diameter of > 3 cm, for example, resting the palm of the hand
on the touch screen
–As soon as the touch screen is no longer touched, input is possible again.

Safety instructions and further information
2.4 Notes about usage
IFP2200 INOX MT ETH
14 Compact Operating Instructions, 07/2021, A5E42185570-AD
Functions of the multi-touch screen
General functions
•Detection of up to 5 finger touches at a time.
•Detection of gestures that are supported by the operating system or the software installed
on the device.
Note
Multi
-touch operation can provide advanced features or pose limitations depending on
the operating system and the software installed on the device. Read the corresponding
documentation.
•You do not need to calibrate the touch screen. Some operating systems do offer touch
calibration. However, this calibration does not result in an improvement of the accuracy.
Security functions in an industrial environment
The touch screen is locked for security reasons when following happens:
•There is a conductive liquid on the touch screen with ground contact via the enclosure or
the operator, for example.
•Electromagnetic interference is present that exceeds the specification according to EN
61000-4-2.
Once the interference is over, the touch screen is no longer locked.
2.4 Notes about usage
Installation location
The touch operating panel is designed for use in open processes and is primarily intended for
use in splash zones (according to DIN EN 1672-2).
NOTICE
The HMI device is approved for indoor use only.
The HMI device may be damaged if it is operated outdoors.
Operate the HMI device indoors only.
Note
Operate the device only in a normal atmospheric environment
The technical characteristics of the device described in the operating
instructions are
guaranteed if you operate the device in normal ambient air conditions with usual air
composition.

Safety instructions and further information
2.4 Notes about usage
IFP2200 INOX MT ETH
Compact Operating Instructions, 07/2021, A5E42185570-AD 15
Note
The device is intended for operation in an SELV/PELV circuit according to IEC/EN
61010-2-201
in a dry environment, which means a
dry environment on the rear of the device.
You can find additional information in the section "Operating conditions (Page 40)".
Industrial applications
The HMI device is designed for industrial applications. It conforms to the following standards:
•Requirements for emissions EN 61000-6-4: 2007 +A1:2011
•Requirements for interference immunity EN 61000-6-2: 2005
Use in mixed-use zone
Under certain circumstances, you can use the HMI device in a mixed-use zone. A mixed-use
zone is used for housing and commercial operations that do not have a significant impact on
residents.
When you use the HMI device in a mixed-use zone, you must ensure that the limits of the
generic standard EN 61000-6-3 regarding emission of radio frequency interference are
observed. Suitable measures for achieving these limits for use in a mixed-use zone include:
•Installation of the HMI device in grounded control cabinets
•Use of filters in electrical supply lines
Individual acceptance is required.
Use in residential areas
Note
HMI device not intended for use in residential area
The HMI device is not intended for use in residential areas. Operation of an HMI device in
residential areas can have a negative influence on radio or TV reception.

Safety instructions and further information
2.5 Use in hazardous areas
IFP2200 INOX MT ETH
16 Compact Operating Instructions, 07/2021, A5E42185570-AD
Use with additional measures
The HMI device should not be used at the following locations unless additional measures are
taken:
•In locations with a high degree of ionizing radiation
•In locations with severe operating conditions, for example, due to:
–Corrosive vapors, gases, oils or chemicals
–Strong electrical or magnetic fields of high intensity
•In systems that require special monitoring, for example, in:
–Elevators
–Systems in especially hazardous rooms
2.5 Use in hazardous areas
The following warnings apply to operating a device with Ex approval in hazardous areas.
WARNING
Explosion Hazard
Do not disconnect while circuit is live unless area is known to be non-hazardous.
Substitution of components may impair suitability for Class I, Division 2 or Zone 2.
Risque d'Explosion
Ne pas déconnecter pendant que le circuit est sous tension, sauf si la zone est non-
dangereuse. Le remplacement de composants peut compromettre leur capacité à satisfaire
à la Classe I, Division 2 ou Zone 2.
WARNING
Do not plug or pull connectors in potentially explosive atmospheres
When you plug or pull the plug-in connector during operation, there is a risk of an arcover.
An explosion can be triggered in the hazardous area due to sparkover, and death or serious
bodily injury can occur.
Pulling or plugging of plug-in connectors, for example, a 24 V DC power supply connector as
well as the memory card is prohibited in the hazardous area.
Plug or pull a plug-in connector only when one of the following two requirements is met:
The area is no longer hazardous or the device and its plug-in connections are de-energized.
To switch off the device, close all open programs or the current project, and switch off the
power to the device.
Also read the enclosed documentation for use in potentially explosive atmospheres and the
information in the section "Certificates and approvals (Page 33)".

IFP2200 INOX MT ETH
Compact Operating Instructions, 07/2021, A5E42185570-AD 17
Installing and connecting the device
3
3.1 Preparing for installation
3.1.1 Check the scope of delivery
Check the scope of delivery for visible signs of damages caused during transport and for
completeness, see chapter "Scope of delivery (Page 8)".
NOTICE
Damaged parts
A damaged part can cause device malfunctions.
Do not install damaged parts.
In the case of damaged parts or incomplete delivery, contact your Siemens representative.
3.1.2 Checking the operating conditions
Note the following aspects before installing the device:
1. Familiarize yourself with the standards, approvals, EMC parameters and technical
specifications for operation of the device. This information is available in the following
chapters:
–Certificates and approvals (Page 33)
–Electromagnetic compatibility (Page 41)
2. Check the mechanical and climatic ambient conditions for operation of the device; see
Ambient conditions (Page 39).
3. Follow the notes on use in the operating instructions.
3.1.3 Permitted mounting positions
The device is suitable for installation in:
•Mounting cabinets
•Control cabinets
•Switchboards
•Consoles
In the following, all of these mounting options are referred to by the general term "cabinet".
The device is self-ventilated and approved for inclined mounting at angles up to +/-35° in
stationary cabinets.

Installing and connecting the device
3.1 Preparing for installation
IFP2200 INOX MT ETH
18 Compact Operating Instructions, 07/2021, A5E42185570-AD
NOTICE
Damage due to overheating
Inclined installation reduces the convection by the device and therefore the maximum
permitted ambient temperature for operation.
If there is sufficient forced ventilation, the device can also be operated in the inclined
mounting position up to the maximum permitted ambient temperature for vertical
installation. The device may otherwise be damaged and its certifications and warranty will
be rendered null and void.
For information on permitted ambient temperatures, refer to the section Operating
conditions (Page 40).
Mounting position
Select one of the approved mounting positions for your device. The approved mounting
positions are described in the following sections.
Mounting in horizontal format
The device is intended for installation in landscape format.
A maximum ambient temperature of +45 °C is permissible for vertical installation.
Mounting in vertical format
You can also install the device in portrait format.
A maximum ambient temperature of +40 °C is permissible for vertical mounting (0° tilt
angle); a maximum of +35 °C is permitted for inclined mounting.

Installing and connecting the device
3.1 Preparing for installation
IFP2200 INOX MT ETH
Compact Operating Instructions, 07/2021, A5E42185570-AD 19
3.1.4 Notes on installation
Mounting cutout
The HMI device can be installed in control cabinets (see table for material thickness). No
special tools are required for mounting. The HMI device can be operated both in landscape
and portrait format with a vertical inclination of up to +/-35°. Due to the surrounding beveling
of the stainless steel front of 45°, liquids are able to drain off even in an inclined installation
position of +/-35°.
The following conditions apply to the mounting cutout:
The front material has to consist of sheet steel or material of a strength that corresponds to at
least the stability of sheet steel.
Mounting cutout
Dimensions
Material thickness
1.5 to 6 mm
Permitted deviation from plane
This condition must be fulfilled for the mounted HMI device.
≤ 0.5 mm
Permitted surface roughness in the area of the mounting seal
≤120 µm (Rz120)
3.1.5 Checking clearances
The following clearances are required around the device to ensure adequate self-ventilation:
•At least 15 mm to the right and left of the mounting cutout (in x direction) to allow for
insertion of the mounting clips during installation
•At least 50 mm above and below the mounting cutout (in y direction) for ventilation
•At least 10 mm behind the rear panel of the device (in z direction)
The figure below shows the clearances required with horizontal and vertical installation of
the device:
①
Clearance for horizontal installation (all devices)
②
Clearance for vertical installation (monitor and touch versions only)
x
At least 15 mm distance
y
At least 50 mm distance
z
At least 10 mm distance

Installing and connecting the device
3.2 Inserting the mounting seal
IFP2200 INOX MT ETH
20 Compact Operating Instructions, 07/2021, A5E42185570-AD
Note
Ensure that the maximum ambient temperature is not exceeded when mounting the device
in a cabinet and especially in a closed enclosure.
3.2 Inserting the mounting seal
To prevent the mounting seal from being inserted in the wrong direction, it has an
asymmetric coding tap. The coding tap is located at the bottom left of all mounting seals of
the INOX devices, relative to the rear of the device.
Note
Use a new mounting seal for each installation, because the promised degree of protection
cannot be guaranteed otherwise.
Procedure
1. Look for the coding tap on the mounting seal. Turn the mounting seal so that the coding tap
is on the bottom left as seen in the figure below:
①
Coding tap
②
Positioning hooks
③
Seal corner