Siemens SIRIUS 3RA2711 Technical Document

Industrial switchgear
Switchgear
SIRIUS 3RA2711 function modules
for IO-Link
Equipment Manual
08/2022
A8E96801709001A/RS-AD/006
Introduction 1
Standards 2
Safety notes 3
Product description 4
Application planning 5
Con󹪝guring the IO-Link 6
Parameters 7
Process image 8
Installing 9
Connecting 10
Operator control 11
Diagnostics 12
Appendix A

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Quali󹪝ed Personnel
The product/system described in this documentation may be operated only by personnel quali󹪝ed for the speci󹪝c
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Quali󹪝ed personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance
are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identi󹪝ed by ® are registered trademarks of SiemensAG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Smart Infrastructure
Electrical Products
Postfach 10 09 53
93009 Regensburg
GERMANY
A8E96801709001A/RS-AD/006
Ⓟ 10/2022 Subject to change
Copyright © SiemensAG 2009.
All rights reserved

Table of contents
1 Introduction ........................................................................................................................................... 7
1.1 Responsibility of the user for system con󹪝guration and functionality..................................... 7
1.2 Purpose of the manual......................................................................................................... 8
1.3 Required basic knowledge.................................................................................................... 9
1.4 Scope of the manual .......................................................................................................... 10
1.5 Siemens Industry Online Support ....................................................................................... 11
1.6 Further documentation...................................................................................................... 13
1.7 DataMatrix code ................................................................................................................ 14
1.8 Siemens Industry Online Support app................................................................................. 16
1.9 Recycling and disposal ....................................................................................................... 17
1.10 Support Request ................................................................................................................ 18
2 Standards............................................................................................................................................. 19
2.1 Standards .......................................................................................................................... 19
2.2 Requirements for switching high-e󹪟ciency motors............................................................. 20
2.3 Voltages ............................................................................................................................ 21
2.4 Notes on the protection of device connections ................................................................... 22
2.5 Approvals, test certi󹪝cates, characteristics .......................................................................... 23
3 Safety notes ......................................................................................................................................... 25
3.1 Current information about operational safety ..................................................................... 25
3.2 Security information .......................................................................................................... 28
4 Product description.............................................................................................................................. 29
4.1 Properties .......................................................................................................................... 29
4.2 Scope of supply ................................................................................................................. 30
4.3 Technical data.................................................................................................................... 34
4.3.1 Technical data in Siemens Industry Online Support............................................................. 34
4.3.2 Overview tables ................................................................................................................ 34
5 Application planning ........................................................................................................................... 35
5.1 Product combinations ........................................................................................................ 35
5.2 Assembly of function modules for IO-Link, direct starting ................................................... 45
5.3 Assembly of function module for IO-Link, reversing starting................................................ 46
5.4 Assembly of function modules for IO-Link, star-delta starting.............................................. 47
SIRIUS 3RA2711 function modules for IO-Link
Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006 3

6Con󹪝guring the IO-Link ....................................................................................................................... 49
6.1 Combinations .................................................................................................................... 49
6.2 Con󹪝guring with STEP 7 and the S7-PCT Port Con󹪝guration Tool ......................................... 50
6.2.1 Basic procedure and prerequisites ...................................................................................... 50
6.2.2 Con󹪝guration..................................................................................................................... 51
6.3 Con󹪝guring with the S7-PCT port con󹪝guration tool (stand-alone) ...................................... 52
6.3.1 Application ........................................................................................................................ 52
6.3.2 Basic procedure and prerequisites ...................................................................................... 52
6.3.3 Con󹪝guration..................................................................................................................... 52
6.4 Block library for IO-Link (LIOLink) ....................................................................................... 54
6.5 Replacing an IO-Link device................................................................................................ 55
6.5.1 Introduction....................................................................................................................... 55
6.5.2 Replacing an IO-Link device according to the IO-Link communication speci󹪝cation V1.0 ...... 55
6.5.2.1 Procedure .......................................................................................................................... 55
6.5.2.2 Procedure with PG/PC......................................................................................................... 55
6.5.2.3 Procedure without PG/PC.................................................................................................... 56
6.5.3 Replacing an IO-Link device according to the IO-Link communication speci󹪝cation V1.1 ...... 56
7 Parameters........................................................................................................................................... 59
7.1 Parameters for starters 1 to 4 ............................................................................................. 60
7.1.1 "Starter type" parameter..................................................................................................... 60
7.1.2 "Starter available" parameter .............................................................................................. 60
7.1.3 Parameter "Operation at Preset <> Actual Operation".......................................................... 61
7.2 Parameters for the operator panel ...................................................................................... 63
7.2.1 "Operator panel available" parameter ................................................................................. 63
7.2.2 Parameter "Operation at Preset <> Actual Operation".......................................................... 63
7.3 Parameters for IO-Link devices (according to IO-Link communication speci󹪝cation V1.1) ..... 65
7.3.1 "Parameter (write) access inhibition" parameter.................................................................. 65
7.3.2 "Data storage inhibition" parameter.................................................................................... 65
8 Process image ...................................................................................................................................... 67
8.1 Process image input (PII) .................................................................................................... 67
8.2 Process image output (PIQ) ................................................................................................ 68
9 Installing .............................................................................................................................................. 69
9.1 Installing function modules for IO-Link ............................................................................... 69
9.2 Connecting IO-Link starters................................................................................................ 73
9.3 Mounting an operator panel .............................................................................................. 75
9.4 Removing function modules for IO-Link.............................................................................. 77
9.5 Mounting the cover sealing................................................................................................ 79
10 Connecting .......................................................................................................................................... 81
10.1 Connection via terminals.................................................................................................... 81
10.2 Connecting function modules for IO-Link ........................................................................... 84
10.3 Input for local shutdown .................................................................................................... 88
Table of contents
SIRIUS 3RA2711 function modules for IO-Link
4Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006

10.4 EMERGENCY STOP.............................................................................................................. 90
11 Operator control .................................................................................................................................. 91
11.1 Settings on the function modules for IO-Link ...................................................................... 91
11.2 Operation using the operator panel.................................................................................... 92
12 Diagnostics .......................................................................................................................................... 97
A Appendix.............................................................................................................................................. 99
A.1 CAx data............................................................................................................................ 99
A.2 Dimension drawings ........................................................................................................ 100
A.3 Circuit diagrams............................................................................................................... 105
A.3.1 Main circuit...................................................................................................................... 105
A.3.2 Control circuit .................................................................................................................. 108
A.4 Data sets.......................................................................................................................... 110
A.4.1 Structure of the data sets ................................................................................................. 110
A.4.2 IO-Link communication parameters.................................................................................. 110
A.4.3 Device-speci󹪝c parameters ............................................................................................... 111
A.4.4 Identi󹪝cation data............................................................................................................ 112
A.4.5 Group diagnostics - data set (index) 90............................................................................. 113
A.4.6 Actual con󹪝guration - data set (index) 105 ....................................................................... 116
A.4.7 Preset con󹪝guration - data set (index) 130........................................................................ 119
A.5 References....................................................................................................................... 122
A.5.1 References....................................................................................................................... 122
A.5.2 Manuals - SIRIUS Modular System..................................................................................... 123
A.6 ESD Guidelines................................................................................................................. 124
A.7 Electromagnetic compatibility (EMC) according to IEC 60947-4-2 ..................................... 126
Index .................................................................................................................................................. 127
Table of contents
SIRIUS 3RA2711 function modules for IO-Link
Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006 5

Table of contents
SIRIUS 3RA2711 function modules for IO-Link
6Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006

Introduction 1
1.1 Responsibility of the user for system con󹪝guration and
functionality
The function modules described here have been developed to carry out communication tasks as
part of a plant or machine. The function modules for IO‑Link are available for direct starting,
reversing starting and star-delta starting.
Siemens AG, its regional o󹪟ces, and associated companies (hereinafter referred to as
"Siemens") cannot guarantee all the properties of an overall installation or machine that
has not been designed by Siemens.
Nor can Siemens assume liability for recommendations that appear or are implied in the
following description. No new guarantee, warranty, or liability claims beyond the scope
of the Siemens general terms of supply are to be derived or inferred from the following
description.
Note
Comply in each case with the valid national assembly regulations and standards when
con󹪝guring the system.
SIRIUS 3RA2711 function modules for IO-Link
Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006 7

1.2 Purpose of the manual
This manual describes the function modules for IO-Link. It provides overview information for
integrating the function modules into the system environment and describes the hardware and
software components of the modules.
The information in this manual enables you to commission the function modules for IO-Link.
Introduction
1.2Purpose of the manual
SIRIUS 3RA2711 function modules for IO-Link
8Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006

1.3 Required basic knowledge
To understand these operating instructions you should have a general knowledge of automation
engineering and low-voltage switchgear.
Introduction
1.3Required basic knowledge
SIRIUS 3RA2711 function modules for IO-Link
Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006 9

1.4 Scope of the manual
This manual is valid for the available function modules for IO-Link. It describes the components
that are valid at the time of publication.
Introduction
1.4Scope of the manual
SIRIUS 3RA2711 function modules for IO-Link
10 Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006

1.5 Siemens Industry Online Support
Information and Service
In Siemens Industry Online Support, you can obtain up-to-date information from our global
support database quickly and simply. To accompany our products and systems, we o󹪜er a wealth
of information and services that provide support in every phase of the lifecycle of your machine
or plant – from planning and implementation, through commissioning, up to maintenance and
modernization:
• Product support
• Application examples
• Services
• Forum
• mySupport
Link: Siemens Industry Online Support (https://support.industry.siemens.com/cs/ww/en/)
Product support
You will 󹪝nd here all the information and comprehensive know-how covering all aspects of your
product:
•FAQs
Our answers to frequently asked questions.
•Manuals/operating instructions
Read online or download, available as PDF or individually con󹪝gurable.
•Certi󹪝cates
Clearly sorted according to approving authority, type and country.
•Characteristic curves
For support in planning and con󹪝guring your system.
•Product announcements
The latest information and news concerning our products.
•Downloads
You can 󹪝nd here updates, service packs, HSPs and much more for your product.
•Application examples
Function blocks, background and system descriptions, performance statements,
demonstration systems, and application examples, clearly explained and represented.
•Technical data
Technical product data for support in planning and implementing your project.
Link: Product support (https://support.industry.siemens.com/cs/ww/en/ps)
mySupport
With "mySupport", your personal workspace, you get the very best out of your Industry Online
Support. Everything to enable you to 󹪝nd the right information every time.
Introduction
1.5Siemens Industry Online Support
SIRIUS 3RA2711 function modules for IO-Link
Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006 11

The following functions are now available:
•Personal messages
Your personal mailbox for exchanging information and managing your contacts
•Inquiries
Use our online form for speci󹪝c solution suggestions, or send your technical inquiry directly
to a specialist in Technical Support
•Noti󹪝cations
Make sure you always have the latest information - individually tailored to your needs
•Filters
Simple management and re-use of your 󹪝lter settings from Product Support and the Technical
Forum
•Favorites / Tags
Create your own knowledge database by assigning "Favorites" and "Tags" to documents –
simply and e󹪟ciently
•Entries last viewed
Clear presentation of your last viewed entries
•Documentation
Con󹪝gure your individual documentation from di󹪜erent manuals – quickly and without
complications
•Personal data
Change personal data and contact information here
•CAx data
Simple access to thousands of items of CAx data such as 3D models, 2D dimension drawings,
EPLAN macros and much more
Introduction
1.5Siemens Industry Online Support
SIRIUS 3RA2711 function modules for IO-Link
12 Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006

1.6 Further documentation
To install and connect the contactors, you require the operating instructions of the contactors
used.
The Appendix"References (Page122)" has a list of the operating instructions.
You can 󹪝nd more information about Siemens IO-Link masters in the corresponding manuals
for the electronic modules 4SI IO‑Link and 4SI SIRIUS (IP20), as well as for ET 200eco PN (IP65).
The range of technical documentation for the various SIMATIC products and automation
systems is available on the Internet (http://www.siemens.com/simatic-tech-doku-portal).
This application example (http://support.automation.siemens.com/WW/view/en/38006560)
describes how to read and write process data and parameterization data of IO‑Link masters
and IO‑Link switching devices.
Introduction
1.6Further documentation
SIRIUS 3RA2711 function modules for IO-Link
Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006 13

1.7 DataMatrix code
A DataMatrix code is lasered on the front of all units of the function modules for IO‑Link, on the
left on the basic module.
In the case of basic and coupling modules, there is a further DataMatrix code behind the labeling
plate.
DataMatrix codes are standardized in ISO/IEC 16022. The DataMatrix codes on Siemens
devices use ECC200 coding for powerful error correction.
The following device information is encoded in the front DataMatrix code as a bit stream:
• Article number
• Serial number (abbreviated)
This information is stored in the following format in the DataMatrix code:
1P Article number + S
Data identi󹪝er Net content Separator Serial number
The following device information is encoded in the front DataMatrix code behind the labeling
plate as a bit stream:
• Article number
• Serial number
• Where appropriate, MAC address
This information is stored in the following format in the DataMatrix code:
1P Article number + S
Data identi󹪝er Net content Separator Serial number
(+ 23S MAC address)
The following device information is encoded in the side rating plate as a bit stream:
• Article number
• Serial number
• Where appropriate, MAC address
This information is stored in the following format in the DataMatrix code:
1P Article number + S
Data identi󹪝er Net content Separator Serial number
(+ 23S MAC address)

Note
The information content is displayed without spaces.
This machine-readable information simpli󹪝es and accelerates handling of the respective
devices.
Introduction
1.7DataMatrix code
SIRIUS 3RA2711 function modules for IO-Link
14 Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006

As well as fast access to the serial numbers of the respective devices for unique identi󹪝cation,
the DataMatrix codes simplify communication with Siemens Technical Support.
Introduction
1.7DataMatrix code
SIRIUS 3RA2711 function modules for IO-Link
Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006 15

1.8 Siemens Industry Online Support app
Siemens Industry Online Support app
The Siemens Industry Online Support app provides you access to all the device-speci󹪝c
information available on the Siemens Industry Online Support portal for a particular article
number, such as operating instructions, manuals, data sheets, FAQs etc.
The Siemens Industry Online Support app is available for Android and iOS:
Android iOS
Introduction
1.8Siemens Industry Online Support app
SIRIUS 3RA2711 function modules for IO-Link
16 Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006

1.9 Recycling and disposal
The available function modules for IO-Link can be recycled, as they are low in pollutants. For
environmentally-friendly recycling and disposal of your electronic waste, please contact a
company certi󹪝ed for the disposal of electronic waste.
Introduction
1.9Recycling and disposal
SIRIUS 3RA2711 function modules for IO-Link
Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006 17

1.10 Support Request
After you have registered, you can use the Support Request form in the online support to send
your question directly to Technical Support:
Support Request: Internet (https://www.siemens.com/support-request)
Introduction
1.10Support Request
SIRIUS 3RA2711 function modules for IO-Link
18 Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006

Standards 2
2.1 Standards
Applicable standards
The function modules comply with the following standards:
Table 2-1 Standards - function modules
Device standards • IEC/EN60947‑1 "Low-voltage switchgear and controlgear: General rules"
• IEC/EN 60947‑4‑1 "Contactors and motor-starters: Electromechanical contac‐
tors and motor-starters"
• IEC/EN60947‑5‑1 "Control circuit devices and switching elements: Electro‐
mechanical control circuit devices"; VDE0660 "Low-voltage switchgear"
• DINEN50042 "Terminal marking"
EMC standard1) • IEC/EN 61000‑6‑2 "Generic standards - Immunity for industrial environments"
• IEC/EN61000‑6‑4 "Generic standards - Emission standard for industrial envi‐
ronments"
Resistance to ex‐
treme climates
• IEC60721‑3‑3 "Classi󹪝cation of environmental conditions"
The function modules are climate-proof according to IEC60721‑3.
Touch protection • IEC/EN60529 "Degrees of protection provided by enclosures"
The function modules are safe to touch in accordance with IEC/EN60529.
1) This is a device of Class A. When used in domestic areas, the device can cause radio interference. Users
may have to take suitable measures.
Reference
SIRIUScomponents have been approved by a whole range of bodies for various sectors (e.g.
shipbuilding). An up-to-date list of approvals appears in the appendix of the Catalog IC10 -
SIRIUS "Industrial Controls" (http://www.siemens.com/sirius/catalogs), and more information,
as well as an option to download certi󹪝cates, can be obtained on the Internet (http://
www.siemens.com/sirius/support).
SIRIUS 3RA2711 function modules for IO-Link
Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006 19

2.2 Requirements for switching high-e󹪟ciency motors
The increased requirements for protection devices and switchgear when switching high-
e󹪟ciency motors are covered by the new utilization categoryAC‑3e introduced in
theIEC60947‑4‑1 product standard.
The utilization category AC‑3e takes into account the higher switch-on characteristic of
e󹪟ciency-enhanced motors. This is re󹪞ected, for example, in a higher starting current when
starting squirrel-cage motors.
All SIRIUS protection devices and switchgear that are subject to the IEC60947‑4‑1 product
standard meet the increased requirements in accordance with utilization categoryAC‑3e and
are suitable for use with high-e󹪟ciency motors.
Standards
2.2Requirements for switching high-e󹪟ciency motors
SIRIUS 3RA2711 function modules for IO-Link
20 Equipment Manual, 08/2022, A8E96801709001A/RS-AD/006