Siemens SIMATIC NET CP 442-1 RNA Technical Document

CP 442-1 RNA
SIMATIC NET
S7-400 - Industrial Ethernet
CP 442
-1 RNA
Equipment Manual
Manual Part B
03/2022
C79000
-G8976-C318-05
Preface
Application and functions
1
Performance data
2
Requirements for use
3
LEDs
4
Installation, wiring,
commissioning, removal
5
Configuration and
operation
6
Diagnostics and
maintenance
7
Technical specifications
8
Approvals
9
PRP-compatible devices
A
Documentation references
B

Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C318-05
Ⓟ
04/2022 Subject to change
Copyright © Siemens AG 2013 - 2022.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

CP 442-1 RNA
Equipment Manual, 03/2022, C79000-G8976-C318-05 3
Preface
Legend:
①
X = Placeholder for hardware version
②
Firmware version
③
LEDs
④
Ethernet interface: Interface X1P1 with 1 x 8-pin RJ-45 jack
⑤RNA interface: Ports X2P1 / X2P2 with 2 x 8-pin RJ-45 jacks
Designed for a redundant subnet
⑥
Label with MAC addresses
Figure 1 CP 442-1 RNA
Validity and product names
This description contains information on the following product
CP 442-1 RNA
Article number 6GK7 442-1RX00-0XE0
Hardware version 2
Firmware version V1.5
Communications processor for SIMATIC S7-400 / S7-400H

Preface
CP 442-1 RNA
4Equipment Manual, 03/2022, C79000-G8976-C318-05
New in this edition
•New hardware version
•New firmware version, with improvements including security-relevant product
improvements.
•New approvals (CCC / UKEX)
•Editorial revision
Replaced manual issue
Replaced manual edition: 03/2019
Current version of the manual and information on the Internet
You will find the current version of this document and additional information (e.g. FAQs) on
using the CP on the Internet at the following address:
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15355)
Select the appropriate entry type in the filter settings.
Manual on DVD
You can find the documentation on the product and the configuration on the "SIMATIC NET
Manual Collection" or "SIMATIC Communication Products" DVD. This DVD contains the
product manuals valid at the time it is created.
Structure of the documentation
The documentation for this device consists of the following parts:
•Manual Part A: Configuration manual "Configuring and Commissioning S7CPs for
Industrial Ethernet", see references /1/ (Page 73).
•Manual Part B: Manual "CP 442-1 RNA" (this manual)
•Program blocks for SIMATIC NET S7 CPs - programming manual, see references /4/
(Page 74)
Contains the detailed description of the program blocks for the following services:
–Open communications services
–Access coordination with FETCH/WRITE
–Connection and system diagnostics

Preface
CP 442-1 RNA
Equipment Manual, 03/2022, C79000-G8976-C318-05 5
Compatibility with other modules - service and maintenance
Note
Read the information regarding extended functions and restrictions in section
Replacing the
modules used with CP 442-1 RNA (Page 58) of this manual!
Address label: Unique MAC address preset for the CP
The CP is supplied with a total of 2 default MAC addresses with the following assignment:
•Ethernet interface
•RNA interface
The two MAC addresses of the Ethernet interface and the RNA interface are printed on the
housing.
If you configure a MAC address (ISO transport connections), we recommend that you use the
MAC address of the relevant interface printed on the module for module configuration!
•This ensures that you assign a unique MAC address in the subnet!
•If you replace a module, the MAC address of the predecessor is adopted when you load
the configuration data; configured ISO transport connections remain operable.
Notes on this document
Abbreviations and names
•CP / device / module
Designations for the full product name
•STEP 7
Name for the STEP 7 V5.5 and STEP 7 Professional configuration tools
Cross-references
In this manual, there are often cross-references to other sections. To return to the original
page after jumping to a cross-reference, some PDF readers support the command <Alt>+<Left
arrow>.
Search
To display all instances of a search term in a list, some PDF readers support the command
<Ctrl>+<Shift>+<F>.

Preface
CP 442-1 RNA
6Equipment Manual, 03/2022, C79000-G8976-C318-05
License conditions
Note
Open source software
Read the license conditions for open source software carefully before using the product. The
acceptance of the disclaimers of liability and warranty it contains is a clear precondition of
the use of open source software.
You will find the license condition
s on the same data medium as this manual under the
following file name:
OSS_CP44x1RNA_86.pdf
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary
and only when appropriate security measures (e.g. firewalls and/or network segmentation)
are in place.
For additional information on industrial security measures that may be implemented, please
visit
Link: (http://www.siemens.com/industrialsecurity)
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers’ exposure to
cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
Link: (https://www.siemens.com/cert)
Firmware
The firmware is signed and encrypted. This ensures that only firmware created by Siemens
can be downloaded to the device.
Note on firmware/software support
Check regularly for new firmware/software versions or security updates and apply them. After
the release of a new version, previous versions are no longer supported and are not
maintained.

Preface
CP 442-1 RNA
Equipment Manual, 03/2022, C79000-G8976-C318-05 7
Device defective
If a fault develops, please send the device to your Siemens representative for repair. Repairs
on-site are not possible.
Decommissioning
Shut down the device properly to prevent unauthorized persons from accessing confidential
data in the device memory.
To do this, restore the factory settings on the device.
Recycling and disposal
The product is low in pollutants, can be recycled and meets the requirements of the WEEE
directive 2012/19/EU "Waste Electrical and Electronic Equipment".
Do not dispose of the product at public disposal sites. For environmentally friendly recycling
and the disposal of your old device contact a certified disposal company for electronic scrap
or your Siemens contact.
Keep to the local regulations.
You will find information on returning the product on the Internet pages of Siemens Industry
Online Support:
Link: (https://support.industry.siemens.com/cs/ww/en/view/109479891)
SIMATIC NET glossary
The SIMATIC NET glossary describes terms that may be used in this document.
You will find the SIMATIC NET glossary in the Siemens Industry Online Support at the
following address:
Link: (https://support.industry.siemens.com/cs/ww/en/view/50305045)
Training, Service & Support
You will find information on training, service and support in the multilanguage document
"DC_support_99.pdf" on the Internet pages of Siemens Industry Online Support:
Link: (https://support.industry.siemens.com/cs/ww/en/view/38652101)

Preface
CP 442-1 RNA
8Equipment Manual, 03/2022, C79000-G8976-C318-05

CP 442-1 RNA
Equipment Manual, 03/2022, C79000-G8976-C318-05 9
Table of contents
Preface ................................................................................................................................................... 3
1 Application and functions.................................................................................................................... 11
1.1 Properties of the CP............................................................................................................ 11
1.2 Communication services .................................................................................................... 12
1.3 Network topology with redundancy (PRP)........................................................................... 13
1.4 Further services and characteristics of the CP...................................................................... 16
2 Performance data ................................................................................................................................ 19
2.1 General characteristic data................................................................................................. 19
2.2 Characteristics of S7 communication.................................................................................. 19
2.3 SEND/RECEIVE interface ..................................................................................................... 20
2.3.1 Characteristic data ............................................................................................................. 20
2.3.2 Number of simultaneous SEND/RECEIVE calls...................................................................... 21
2.4 Characteristics of open TCP/IP communication.................................................................... 23
2.5 Characteristic data of TCP connections for HTTP.................................................................. 23
3 Requirements for use .......................................................................................................................... 25
3.1 Configuration limits ........................................................................................................... 25
3.2 System environment.......................................................................................................... 25
3.3 Project engineering............................................................................................................ 27
3.4 Program blocks .................................................................................................................. 27
4 LEDs ..................................................................................................................................................... 29
5 Installation, wiring, commissioning, removal ..................................................................................... 33
5.1 Important notes on using the device .................................................................................. 33
5.1.1 Notices on use in hazardous areas...................................................................................... 33
5.1.2 Notes on use in hazardous areas according to ATEX / UKEX / IECEx / CCC-Ex ........................ 33
5.1.3 Notes on use in hazardous areas according to UL HazLoc and FM........................................ 34
5.2 Installation, removal and repairs in hazardous areas ........................................................... 35
5.3 Installing and connecting................................................................................................... 36
5.4 Commissioning.................................................................................................................. 38
5.4.1 Commissioning - procedure................................................................................................ 38
5.4.2 Controlling the mode......................................................................................................... 38
5.5 Disassembly....................................................................................................................... 39
6 Configuration and operation............................................................................................................... 41
6.1 Security recommendations................................................................................................. 41

Table of contents
CP 442-1 RNA
10 Equipment Manual, 03/2022, C79000-G8976-C318-05
6.2 Switching over interfaces................................................................................................... 44
6.3 Memory reset / reset to factory defaults ............................................................................. 44
6.4 Network settings ............................................................................................................... 46
6.4.1 Reserved MAC address....................................................................................................... 46
6.4.2 Transmission properties of the Ethernet and RNA interfaces ............................................... 46
6.5 IP configuration ................................................................................................................. 48
6.5.1 Setting the IP address......................................................................................................... 48
6.5.2 Detecting duplicate IP addressing in the network................................................................ 48
6.6 Time-of-day synchronization.............................................................................................. 49
6.7 Recommendation for use with a high communications load ............................................... 49
6.8 SNMP agent....................................................................................................................... 50
6.9 Interface in the user program............................................................................................. 52
6.9.1 Call interface for open communications services SEND/RECV............................................... 52
6.9.2 Open TCP/IP communication .............................................................................................. 52
6.10 Ping: Permitted length of ICMP packets .............................................................................. 53
6.11 Communication in PRP mode ............................................................................................. 54
7 Diagnostics and maintenance ............................................................................................................. 55
7.1 Diagnostics options............................................................................................................ 55
7.2 The CP as Web server ......................................................................................................... 56
7.3 Loading new firmware....................................................................................................... 57
7.4 Replacing the modules used with CP 442-1 RNA................................................................. 58
7.5 Replacing a module without a programming device ........................................................... 60
8 Technical specifications....................................................................................................................... 61
9 Approvals............................................................................................................................................. 63
A PRP-compatible devices....................................................................................................................... 69
B Documentation references.................................................................................................................. 73
Index.................................................................................................................................................... 77

CP 442-1 RNA
Equipment Manual, 03/2022, C79000-G8976-C318-05 11
Application and functions
1
1.1 Properties of the CP
Application
The CP is intended for use in an S7400 or S7400H (faulttolerant) automation system. It allows
the S7400 / S7400H to be connected to Industrial Ethernet.
The CP has the following interfaces:
•Ethernet interface
The CP has a 100 Mbps Ethernet interface. The Ethernet interface can be used as an
alternative to the RNA interface. The Ethernet interface can, for example, be used to
connect to a PG/PC or to a higherlevel company network.
For special situations, each port can be set to a fixed mode manually using STEP 7, for
example 10 or 100 Mbps half duplex / full duplex.
•RNA interface
The RNA interface has 2 ports. These two ports are used as follows:
–PRP mode with both ports as a redundancy solution
–Port 1 as the only used port of the RNA interface with 100 Mbps full duplex (port 2 is
disabled)
The RNA interface only supports the "automatic setting" mode with 100 Mbps full duplex.
The communications partner must use the same settings.
Each port supports autocrossing and autonegotiation and is equipped with a combined
RXD/TXD / LINK dual LED for simple diagnostics.
Note
Interfaces can only operated as alternatives
The Ethernet interface or the RNA interface can only be enabled as alternatives (one or the
other). Simultaneous use of both interfaces is not possible. These are activated during
configuration with STEP 7. Note
further information in the section Switching over interfaces
(Page 44)

Application and functions
1.2 Communication services
CP 442-1 RNA
12 Equipment Manual, 03/2022, C79000-G8976-C318-05
①
Connection to port X1P1 of the Ethernet interface (ISO transport)
②
Connection of the RNA interface to a PRP network
③
Connection to port X2P1 of the RNA interface (ISO transport / ISO-on-TCP / TCP)
Figure 1-1 CP 442-1 RNA - connection variants
1.2 Communication services
Depending on the interface being used, the CP supports the following communications
services:
•S7 communication with the following functions:
–PG functions;
–Operator monitoring and control functions;
–Data exchange over S7 connections.
•Open communication services with the following functions:
–SEND/RECEIVE interface over ISO transport connections;
–SEND/RECEIVE interface over TCP connections, ISOonTCP and UDP connections;
With the SEND/RECEIVE interface via TCP connections, the CP supports the socket
interface to TCP/IP available on practically every end system.
UDP frame buffering on the CP can be disabled during configuration. When necessary,
this allows you to achieve a shorter reaction time between the arrival of a UDP frame
and its evaluation on the CPU.
–Multicast over UDP connection
The multicast mode is made possible by selecting a suitable IP address when
configuring connections.
–FETCH/WRITE services (server services; corresponding to S5 protocol) via ISO transport
connections, ISOonTCP connections and TCP connections;
Here, the SIMATIC S7400 with the CP is always the server (passive connection
establishment) while the fetch or write access (client function with active connection
establishment) is always initiated by a SIMATIC S5 or a device from another range / PC.
–LOCK/UNLOCK with FETCH/WRITE services (CPUdependent; see section Requirements
for use (Page 25));

Application and functions
1.3 Network topology with redundancy (PRP)
CP 442-1 RNA
Equipment Manual, 03/2022, C79000-G8976-C318-05 13
•Open TCP/IP communication
Open TCP/IP communication provides a program interface for the transfer of connection-
oriented and connectionless services. The establishment and termination of connections is
initiated here only via the "dynamic" program interface.
STEP 7 provides a UDT for the connection parameter assignment as well as four FBs for
high-speed data exchange.
The CP supports communication via ISO-on-TCP connections for this interface.
Interfaces used and communications services
The following table provides an overview of the services available at the interfaces.
Communications service
Ethernet interface
RNA interface
S7 communication
PG functions; operator control and monitoring
functions (ISO)
x
x
PG functions; operator control and monitoring
functions (ISO-on-TCP)
-
x
Data exchange over S7 connections (ISO)
x
x
Data exchange over S7 connections (TCP)
-
x
Open communications
services using
SEND/RECEIVE
interface
ISO transport connections
x
x
TCP connections, ISOonTCP and UDP connections
-
x
Multicast over UDP connection
-
x
FETCH/WRITE services (ISO)
x
x
FETCH/WRITE services (RFC, TCP)
-
x
Open TCP/IP
communication
-
x
Time of day
NTP mode and SIMATIC mode
-
x
H connections
via ISO
x
x
via TCP
-
x
1.3 Network topology with redundancy (PRP)
Redundant Network Access (RNA)
In Siemens Industry, Redundant Network Access (RNA) stands for devices and software that
support the redundancy protocol "Parallel Redundancy Protocol" (PRP). RNA allows the
connection of devices to redundant Ethernet network structures.
The product names of the RNA devices end with "RNA".
Some devices of the SCALANCE X-200RNA product line also support the redundancy protocol
"High-availability Seamless Redundancy" (HSR).

Application and functions
1.3 Network topology with redundancy (PRP)
CP 442-1 RNA
14 Equipment Manual, 03/2022, C79000-G8976-C318-05
Parallel Redundancy Protocol (PRP)
The Parallel Redundancy Protocol (PRP) is a redundancy protocol for Ethernet networks. It is
specified in IEC 62439-3.
The areas of application of PRP are distributed applications with high reliability demands that
depend on the high availability of the network. Compared with classic fault-tolerant
networks, bumpless path redundancy is possible with PRP.
PRP has the advantage that it uses parallel, separate networks made up of standard network
components. End devices that use this method are connected to both networks via two ports
of an interface of the device or via a SCALANCE X-200RNA or a RUGGEDCOM RS950G. This
means that data of the end device can be transferred at the same time via both networks. If a
transmission path is interrupted, the data reaches the communications partner via the second
parallel path.
If a network is interrupted, communication can be maintained with PRP via the second
network without any interruption. Reconfiguration times required with the other redundancy
protocols (e.g. MRP) do not therefore apply.
An end device with PRP capability can be connected to redundant networks by using the PRP
protocol. An end device that does not have PRP capability can be connected to a redundant
network via a SCALANCE X-200RNA or RUGGEDCOM RS950G that does have PRP capability.
This means that PRP can also be used by end devices without PRP capability.
Devices with PRP capability are located in two independent networks with the same MAC and
IP address.
Communication with PRP
PRP is only possible when two end devices are connected via two independent networks (LAN
A and LAN B).
Each end device is represented in both networks LAN A and LAN B with the same MAC and IP
address.
PRP communication is handled using the following mechanisms:
•Send
An end device with PRP capability duplicates each frame to be sent on the PRP interface.
The two duplicates are sent via the 2 ports of the PRP interface via the two separate
networks LAN A and LAN B to the communications partner.
If the end device does not have PRP capability, the frame to be sent is duplicated by an X-
200RNA to which the end device is connected and sent via LAN A and LAN B to the
communications partner.
•Received
The two duplicates are received by an end device with PRP capability via LAN A and LAN B
on the two ports of the PRP interface.
If the end device does not have PRP capability, the receiving end device must be preceded
by an X-200RNA. The X-200RNA forwards the first frame to arrive to the addressee. The
second frame is discarded ((N-1) redundancy).

Application and functions
1.3 Network topology with redundancy (PRP)
CP 442-1 RNA
Equipment Manual, 03/2022, C79000-G8976-C318-05 15
Connecting up and cabling
Each frame duplicate sent using the PRP mechanisms is given in identifier that specifies
whether it is sent via LAN A or LAN B.
Note
Cabling
Make sure that all the PRP ports of the node
s and the SCALANCE X204RNA / RUGGEDCOM
RS950G on LAN A and LAN B are connected correctly. A frame with the identifier "LAN A"
must be received at the corresponding port.
The PRP ports of SIMATIC NET devices have the following identifiers. The CP ports are the
ports of the interface with PRP capability.
•Ports for connection to LAN A
–CPs: X2/P1
–SCALANCE X204RNA: PRP A
•Ports for connection to LAN B
–CPs: X2/P2
–SCALANCE X204RNA: PRP B
How is a redundant PRP network set up?
A network topology in which the Parallel Redundancy Protocol is used (PRP network) consists
of two separate Ethernet subnets. The structure of the two subnets does not need to be
identical.
A PRP network can be set up both with end devices with PRP capability as well as with
standard components. The following devices can be used:
•End devices with PRP capability (Double Attached Nodes PRP, Double Attached Node
implementing PRP, DANP), for example:
–CP 443-1 RNA
–PC with SOFTNET-IE RNA
–SIPROTEC protective devices with PRP capability
•Standard components (Singly Attached Nodes, SAN)
Standard components without PRP functionality, for example, can be connected to a PRP
network via SCALANCE X-200RNA or RuggedCom RS950G.
SANs can, however, also be connected to a PRP network without supporting the PRP
functionality.
All devices that are intended to use the PRP function in redundant networks must be able to
process frames with length of up to 1532 bytes (oversize frames). If this function is not
supported, data may be lost.

Application and functions
1.4 Further services and characteristics of the CP
CP 442-1 RNA
16 Equipment Manual, 03/2022, C79000-G8976-C318-05
Example of a configuration for a PRP network
The following figure shows the options for connecting devices in a network topology in
which the Parallel Redundancy Protocol (PRP) is used.
Figure 1-2 Example of the configuration of a network topology with PRP
1.4 Further services and characteristics of the CP
•Timeofday synchronization over the RNA interface using the following configurable
modes:
–SIMATIC mode
The CP receives MMS timeofday messages and synchronizes its local time.
You can choose whether or not the time of day is forwarded. You can also decide on
the direction in which it is forwarded.
or
–NTP mode (NTP: Network Time Protocol)
The CP sends timeofday queries at regular intervals to an NTP server and synchronizes
its local time of day.
The time can also be forwarded automatically to the CPU modules in the S7 station
allowing the time to be synchronized in the entire S7 station.
•Addressable with the factoryset MAC address
To assign the IP address to a new CP (direct from the factory), it can be accessed using the
preset MAC address on port X2P1 of the RNA interface. Online address assignment is
made in STEP 7.

Application and functions
1.4 Further services and characteristics of the CP
CP 442-1 RNA
Equipment Manual, 03/2022, C79000-G8976-C318-05 17
•SNMP agent on the RNA interface
The CP supports data queries over SNMP in version V1 (Simple Network Management
Protocol). It delivers the content of certain MIB objects according to the MIB II standard
(RFC 1213), PRP-MIB IEC62439 (IEC-62439-3-MIB) and Automation MIB.
•Module access protection
To protect the module from accidental or unauthorized access, protection can be
configured at various levels.
•IP access protection on the RNA interface (IPACL)
Using IP access protection gives you the opportunity of restricting communication over
the CP of the local S7 station to partners with specific IP addresses.
•Web diagnostics on the RNA interface
With the aid of Web diagnostics, you can read out the diagnostics data from a station
connected via the CP to a PG/PC with a Web browser.
The Web pages contain the following information:
–Module and status information
•Diagnostics buffer extract request
With the aid of a Web browser, the CP supports the option of obtaining an extract of the
diagnostics buffer containing the most recent diagnostics events of the CPUs and CPs
located in the same S7 station as the CP.
•Connection diagnostics with the AG_CNTEX program block
With the AG_CNTEX program block, you can diagnose connections.
–When necessary, you can activate or deactivate connections or initiate reestablishment
of a connection.
–You can check the reachability of the connection partners using the PING function (on
the RNA interface).
–You can find out which connection types are set up on the RNA interface for the SEND /
RECEIVE function.
•S5/S7 addressing mode
The addressing mode can be configured for FETCH/WRITE access as the S7 or S5
addressing mode (S7 addressing mode only for data blocks / DBs).
•Detecting IP double addressing in the network on the RNA interface
To save you timeconsuming troubleshooting in the network, the CP detects double
addressing in the network.
For more detailed information, see section Detecting duplicate IP addressing in the
network (Page 48)

Application and functions
1.4 Further services and characteristics of the CP
CP 442-1 RNA
18 Equipment Manual, 03/2022, C79000-G8976-C318-05
•Support in the fault-tolerant system (H system)
S7 communication is supported in the H system with the following protocols:
–Ethernet interface
ISO transport
–RNA interface
ISO transport and ISO-on-TCP (RFC1006)

CP 442-1 RNA
Equipment Manual, 03/2022, C79000-G8976-C318-05 19
Performance data
2
2.1 General characteristic data
Characteristic
Explanation / values
Total number of connections on Industrial Ethernet
128
The value applies to the total number of connections of the
following types:
•S7 connections
•SEND/RECEIVE connections
Example
You can, for example, operate the following combination of connections:
•62 S7 connections or 62 H connections
•30 ISO-on-TCP connections
•10 TCP connections
•10 UDP connections
•8 ISO transport connections
2.2 Characteristics of S7 communication
S7 communication provides data transfer via the ISO Transport or ISO-on-TCP protocols.
Characteristic
Explanation / values
Total number of S7 connections on Industrial
Ethernet
128 max.,
of those max. 62 H connections
LAN interface - data field length generated by CP
per protocol data unit
•sending
•receiving
480 bytes / PDU
480 bytes / PDU
•Number of PG connections
•Number of OP connections
2 max.
30 max.

Performance data
2.3 SEND/RECEIVE interface
CP 442-1 RNA
20 Equipment Manual, 03/2022, C79000-G8976-C318-05
Note
Effects of connections in the SPEED SEND/RECV mode
Note the effects of connections on the SEND/RECEIVE interface that are used in the SPEED
SEND/RECEIVE mode.
The maximum configuration limits of S7 communication are reduced by each configured
connection using the SPEED SEND/RECV mode.
2.3 SEND/RECEIVE interface
2.3.1 Characteristic data
The SEND/RECEIVE interface provides access to communication over TCP, ISOonTCP, ISO
transport and UDP connections.
The following characteristics are important:
Characteristic
Explanation / values
Number of SEND/RECEIVE connections •TCP connections: 1...64 1)
•ISO-on-TCP connections: 1...64
•ISO transport connections: 1...64
•Total number of UDP connections (specified and free) that can be
configured: 1 to 64 (of those up to 48 in multicast mode)
•Max. number of connections in total:
(ISO transport and ISOonTCP
+ TCP + UDP) <= 64
Refer to the example in section 5.1 (Page 19)
Notes:
•1) Avoid overload at receiving end
The flow control on TCP connections cannot control permanent
overload of the recipient. You should therefore make sure that the
processing capabilities of a receiving CP are not permanently exceeded
by the sender (approximately 150200 messages per second).
Number of SEND/RECV connections in SPEED
SEND/RECV mode The number depends on the CPU type being used.
•Per CPU 412/414 maximum 30
•Per CPU 416/417 maximum 62
Maximum data length for AG_SEND and
AG_RECV program blocks
AG_SEND and AG_RECV were shipped with other CPs of the S7-400 family
and allowed the transfer of user data with a length of 1 to 240 bytes. The
version of the CP described here continues to support these program
blocks.