Siemens CSI Host Driver User manual

Installation Instructions
Document No. 565-718
December 15, 2009
CSI Host Driver for PXC Modular
These installation instructions cover the connection of
the CSI Host Driver to the CSI System. For hardware
installation of the PXC Modular, see document
number 553-638.
Product Description
The CSI Host Driver enables communication
between the APOGEE®Automation System and the
CSI system.
Product Numbers
PXC00-PE96.A PXC Modular RS-485 or Ethernet
ALN, 96 FLN nodes
PXC00-E96.A PXC Modular with BACnet/IP
ALN and BACnet MS/TP ALN, 96
FLN nodes
PXC100-PE96.A PXC Modular RS-485 or Ethernet
ALN, TX-I/O Support, 96 FLN
nodes
PXC100-E96.A PXC Modular BACnet/IP ALN
and BACnet MS/TP ALN, TX-I/O
Support, 96 FLN nodes
PXX-485.3 Expansion Module, three RS-485
FLN connections
LSM-INT-CSIHOST License for CSI Host PXC
Modular Driver
Accessories
538-670 Trunk Interface II, 115V
538-675 Trunk Interface II, 230V
536-004 Modem Cable, DB-9 Female/DB-25
Male, Serial
Warning/Caution Notations
WARNING:
Personal injury/loss of life may occur if you
do not follow the procedures as specified.
CAUTION:
Equipment damage or loss of data may
occur if you do not follow the procedures
as specified.
Expected Installation Times
The expected installation time is 30 minutes.
Required Tools and Materials
• Flat-blade screwdriver (1/8-inch blade width).
• Wire strippers.
• Cabling and connectors. See the Connecting
the CSI Host Driver to the CSI System section.
CAUTION:
Always wear an electro-static discharge
wrist strap and discharge accumulated
static before touching field panel
components.
Prerequisites
• Driver hardware is installed according to its
respective installation instructions.
•FLNTerm
ination blocks installed, if any.
Depending on the type of installation, other
prerequisites may have to be completed.
Item Number: 565-718, Rev. AA Page 1 of 4

Document No. 565-718
Installation Instructions
December 15, 2009
Connecting the CSI Host Driver to
the CSI System
Follow these steps to connect the CSI Host Driver
to the CSI system:
1. Make cables per diagram in Figure 1 or Figure 2.
2. Install the Trunk Interface II per diagram in
Figure 1 or Figure 2.
3. Connect cables per diagram in Figure 1 or
Figure 2.
4. Plug in the power supply for the Trunk Interface II
per diagram in Figure 1 or Figure 2.
FLN DRIVER
S
-
+
EACH FLN CONNECTOR REQUIRES
RS-485 TRUNK CABLE (MAX 4000 ft/1200 m;
STANDARD 24 AWG LOW CAPACITANCE)
GROUND WIRE TO EARTH
(P/N 538-583)
POWER PACK
TRUNK INTERFACE II
GW1173R3
RS-232 PORT
(25-PIN FEMALE)
RS-232 PORT
(9-PIN MALE)
POWER
TAPE BACK
SHIELD
FLN
S
-
+
IF DRIVER
IS LESS THAN
50 CABLE FEET
(15 m)
FROM CSI PANEL
PLACE THE TRUNK
INTERFACE II
IN THE MBC
ENCLOSURE
237
235
25-PIN MALE TO 9-PIN FEMALE
(P/N 536-004)
CSI DCU or
PCU Controller
with RS-232 Port
CABLE:
Figure 1. Connecting the Driver to the CSI System (Recommended).
Page 2 of 4 Siemens Industry, Inc.

Document No. 565-718
Installation Instructions
December 15, 2009
FLN DRIVER
S
-
+
EACH FLN CONNECTOR REQUIRES
RS-485 TRUNK CABLE (MAX 4000 ft/1200 m;
STANDARD 24 AWG LOW CAPACITANCE)
GROUND WIRE TO EARTH
(P/N 538-583)
POWER PACK
TRUNK INTERFACE II
GW1132R3
RS-232 PORT
(25-PIN FEMALE)
PORT A
POWER
TAPE BACK
SHIELD
FLN
S
-
+
1
2
+
-
IF DRIVER IS
LESS THAN
50 CABLE FEET
(15 m)
FROM CSI PANEL
PLACE THE TRUNK
INTERFACE II
IN THE MBC
ENCLOSURE
23 7
25-PIN MALE TO 9-PIN FEMALE
(P/N 536-004)
TO CSI
LAN
78010 (HOST) TAP
9-PIN RIBBON CABLE
CSI PART #CBL004
NULL MODEM CONNECTOR:
PORT B
TB2
CABLE:
9-PIN (MALE) TO 9-PIN (MALE)
Figure 2. Connecting the Driver to the CSI System via 78010 (Host) Tap.
Siemens Industry, Inc. Page 3 of 4

Document No. 565-718
Installation Instructions
December 15, 2009
Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as
design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners.
© 2009 Siemens Industry, Inc.
Siemens Industry, Inc. Your feedback is important to us. If you have Document No. 565-718
1000 Deerfield Parkway comments about this document, send them to Country of Origin: US
Buffalo Grove, IL 60089-4513 SBT_technical.editor[email protected]. Page 4 of 4
U.S.A.