Siemens SITRANS AID IQ User manual

SITRANS AID IQ
Digitalization
Analyzer Intelligence Director
Operating Instructions
7KU0001-0... (SITRANS AID IQ with up to 6 bus nodes)
7KU0001-1... (SITRANS AID IQ with up to 10 bus nodes)
05/2022
A5E51328515-AA
Introduction 1
System design 2
Commissioning 3
Service and maintenance 4
Troubleshooting 5
Technical data 6
Ordering data 7
Product documentation and
support A
Parameter lists and events
from the software B

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage
to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices
referring only to property damage have no safety alert symbol. These notices shown below are graded according to
the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Quali󹪝ed Personnel
The product/system described in this documentation may be operated only by personnel quali󹪝ed for the speci󹪝c
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Quali󹪝ed personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance
are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identi󹪝ed by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may
be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E51328515
Ⓟ 05/2022 Subject to change
Copyright © Siemens AG 2022.
All rights reserved

Table of contents
1 Introduction ........................................................................................................................................... 5
1.1 Purpose of this documentation ............................................................................................ 5
1.2 Document history ................................................................................................................ 5
1.3 Designated use .................................................................................................................... 5
1.4 Checking the consignment................................................................................................... 5
1.5 Scope of delivery ................................................................................................................. 6
1.6 Industrial use note ............................................................................................................... 6
1.7 Security information ............................................................................................................ 7
1.8 Notes on warranty ............................................................................................................... 8
2 System design........................................................................................................................................ 9
3 Commissioning .................................................................................................................................... 11
3.1 Installing and connecting SITRANS AID IQ........................................................................... 11
3.2 Con󹪝guring a new network ................................................................................................ 12
3.3 Integrating SITRANS AID IQ into an existing network........................................................... 14
3.4 Changing the SIMATIC HMI network settings ...................................................................... 15
3.4.1 Desktop and Start Center ................................................................................................... 16
3.4.2 Entering the IP address and name server ............................................................................ 17
3.4.3 Editing IP addresses and communication connections......................................................... 19
3.4.3.1 Overview........................................................................................................................... 19
3.4.3.2 Assigning IP address and device name................................................................................ 19
3.4.3.3 Con󹪝guring a communication connection .......................................................................... 22
3.5 Calling the SITRANS AID IQ web server ............................................................................... 25
3.6 Call up SITRANS AID IQ on the SIMATIC HMI........................................................................ 27
4 Service and maintenance .................................................................................................................... 31
4.1 Maintenance and repair work............................................................................................. 31
4.2 Ordering of spare parts ...................................................................................................... 31
4.3 Return procedure............................................................................................................... 32
4.4 Disposal............................................................................................................................. 33
5 Troubleshooting................................................................................................................................... 35
6 Technical data...................................................................................................................................... 37
7 Ordering data ...................................................................................................................................... 39
A Product documentation and support .................................................................................................. 41
A.1 Product documentation ..................................................................................................... 41
Analyzer Intelligence Director
Operating Instructions, 05/2022, A5E51328515-AA 3

A.2 Technical support............................................................................................................... 41
B Parameter lists and events from the software .................................................................................... 43
B.1 Introduction....................................................................................................................... 43
B.2 Parameter list for SIPROCESS GA700................................................................................... 43
B.3 Parameter list for CGA Series 6 and ULTRAMAT 23............................................................... 45
B.4 Events ............................................................................................................................... 47
Index .................................................................................................................................................... 49
Table of contents
Analyzer Intelligence Director
4Operating Instructions, 05/2022, A5E51328515-AA

Introduction 1
1.1 Purpose of this documentation
These instructions contain all information required to commission and use the device. Read the
instructions carefully prior to installation and commissioning. In order to use the device
correctly, 󹪝rst review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it
electronically, con󹪝guring the parameters and commissioning it, as well as service and
maintenance engineers.
See also
Technical support (Page 41)
1.2 Document history
The overview below summarizes the most important changes in the documentation when
compared to the previous edition.
Edition Remarks
05/2022 First edition
1.3 Designated use
Use the device in accordance with the information on the nameplate and in the Technical data
(Page 37).
1.4 Checking the consignment
1. Check the packaging and the delivered items for visible damages.
2. Report any claims for damages immediately to the shipping company.
Analyzer Intelligence Director
Operating Instructions, 05/2022, A5E51328515-AA 5

3. Retain damaged parts for clari󹪝cation.
4. Check the scope of delivery by comparing your order to the shipping documents for
correctness and completeness.
WARNING
Using a damaged or incomplete device
Risk of explosion in hazardous areas.
• Do not use damaged or incomplete devices.
1.5 Scope of delivery
Your ordered SITRANS AID IQ contains the following components:
• PLC (SIMATIC S7-1500) con󹪝gured with SITRANS AID IQ software and SD card
• COM module, CM PTP RS422/485 BA
Optional
• SIMATIC HMI 4 or 7 inch with SITRANS AID IQ software
• Power supply
• Mounting rail, 245 mm
• Components of the network infrastructure
Note
Product compatibility with SIPROCESS GA700 base unit
SITRANS AID IQ requires the 󹪝rmware version 1.50.5 VM / PU (03/2019) and higher for the
SIPROCESS GA700 base unit
• If required, update the 󹪝rmware of the SIPROCESS GA700 base unit.
1.6 Industrial use note
NOTICE
Use in a domestic environment
This Class A Group 1 equipment is intended for use in industrial areas.
In a domestic environment this device may cause radio interference.
Introduction
1.6 Industrial use note
Analyzer Intelligence Director
6Operating Instructions, 05/2022, A5E51328515-AA

1.7 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is necessary
to implement – and continuously maintain – a holistic, state-of-the-art industrial security
concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected to
an enterprise network or the internet if and to the extent such a connection is necessary and only
when appropriate security measures (e.g. 󹪝rewalls and/or network segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit
https://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Use of product versions that are no longer
supported, and failure to apply the latest updates may increase customer’s exposure to cyber
threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS Feed
under
https://www.siemens.com/cert.
Software security functions
• Keep the 󹪝rmware of your devices up-to-date. Check regularly whether security updates are
available for your device: Industrial Security website (http://www.siemens.com/
industrialsecurity).
• Check regularly for security recommendations on Siemens ProductCERT (https://
www.siemens.com/cert/en/cert-security-advisories.htm).
• Check whether VLAN structuring in your environment is practical and helpful. VLAN
structuring allows protection against DoS attacks and unauthorized access.
Available protocols
The following list provides an overview of the open protocol ports.
Use the information on the open protocol ports for your settings of the environment which
satisfy the security requirements. Prevent access to protocols that are not used
Protocol Port number Port status Factory setting of
the port status
Authentication of
the communica‐
tion partner
Encryption of
transmission
SNMP UDP/161 Open Open - -
S7 TCP/102 Open Open - -
HTTPS TCP/443 Open Open - Yes
Modbus TCP TCP/502 Open Open - -
Introduction
1.7 Security information
Analyzer Intelligence Director
Operating Instructions, 05/2022, A5E51328515-AA 7

Actively used protocols
The following list shows you an overview of the protocols to obtain the device data and a
SIMATIC HMI connection.
• Modbus TCP protocol
For connection of the SIPROCESS GA700 gas analyzer
• S7 protocol
For connection of the SIMATIC HMI
WARNING
Unsafe operating states as a consequence of software manipulations
Software manipulations (for example Trojans, viruses, malware or worms) can lead to unsafe
operating states in your system that may result in death, severe injuries and property damage.
Always use the most recent software version.
• Integrate the automation and drive components into a holistic industrial security concept in
accordance with the state-of-the-art industrial security concept for the system or machine.
• Ensure that all installed products are included in this holistic industrial security concept.
• Protect 󹪝les that are saved on removable storage media against malware through suitable
measures, such as virus scanners.
WARNING
Unsafe operation
Software manipulation can cause an unsafe operating state of your system.
• Only use the SITRANS AID IQ web server in the local network with suitable security
measures.
• Access the SITRANS AID IQ web server via an SSL connection. For example, with a permitted
list or other security mechanisms.
1.8 Notes on warranty
The contents of this manual shall not become part of or modify any prior or existing agreement,
commitment or legal relationship. The sales contract contains all obligations on the part of
Siemens as well as the complete and solely applicable warranty conditions. Any statements
regarding device versions described in the manual do not create new warranties or modify the
existing warranty.
The content re󹪞ects the technical status at the time of publishing. Siemens reserves the right to
make technical changes in the course of further development.
Introduction
1.8 Notes on warranty
Analyzer Intelligence Director
8Operating Instructions, 05/2022, A5E51328515-AA

System design 2
The SIMATIC S7-1500 included in the scope of delivery (Page 6) of the SITRANS AID IQ allows you
to integrate your gas analyzers SIPROCESS GA700, CGA Series 6 and ULTRAMAT 23 into a
network. Integrate your gas analyzers SIPROCESS GA700 via Ethernet and CGA Series 6 and
ULTRAMAT 23 via ELAN. You can connect a total of up to 10 bus nodes. A CGA Series 6 device
with 2 channels corresponds to 2 bus nodes, since each channel has its own bus address.
The availability of the connected gas analyzers is shown on the SITRANS AID IQ's own web server
and the SIMATIC HMI. The software visualizes the priority of the events and their action
recommendations through NAMUR NE 107 symbols. The events are based on the internal
diagnostics data of the gas analyzers and let you plan maintenance activities and protect your
system better against undesired downtimes.
You can use up to 3 web clients and a SIMATIC HMI or only use one of two display options.
34&-"/&UIFSOFU6QUPCVTOPEFT6QUP4*53"/4"*%*2XFCDMJFOUT7JTVBMJ[BUJPO$POOFDUJWJUZ'JFMEEFWJDFT%$7DIBOOFMTDPSSFTQPOEUPCVTOPEFT1-$4*."5*$).*4*130$&44("$("4FSJF6-53"."54*130$&44("4*5011.$.15134#"
Analyzer Intelligence Director
Operating Instructions, 05/2022, A5E51328515-AA 9

System design
Analyzer Intelligence Director
10 Operating Instructions, 05/2022, A5E51328515-AA

Commissioning 3
3.1 Installing and connecting SITRANS AID IQ
Requirement
SITRANS AID IQ consists of various individual components. For secure operation of
SITRANS AID IQ, follow all instructions of the connected devices.
• Before you start, also follow the following instructions of the SITRANS AID IQ individual
components.
PLC
SIMATIC S7-1500 CPU 1511-1 PN Equipment Manual (https://support.industry.siemens.com/
cs/de/de/view/109752841/en)
SIMATIC S7-1500, ET 200MP Automation system - System Manual (https://
support.industry.siemens.com/cs/ch/de/view/59191792/en)
SIMATIC HMI
SIMATIC HMI – HMI Devices – Comfort Panels – Operating Instructions (https://
support.industry.siemens.com/cs/ch/de/view/49313233/en)
COM module CM PTP RS422/485 BA
SIMATIC S7-1500 CM PtP RS422/485 BA - Equipment Manual (https://
support.industry.siemens.com/cs/ww/de/view/59057390/en)
Power supply
SIMATIC S7-1500/ET 200MP Load power supply module PM 70 W 120/230VAC - Equipment
Manual (https://support.industry.siemens.com/cs/ch/de/view/68036174/en)
• Before you start, follow the instructions of your connected gas analyzers.
Extractive continuous process gas analytics - Instructions (https://
support.industry.siemens.com/cs/ww/en/ps/17721/man)
• You have carried out a manual or automatic calibration (validation/calibration) for all
connected gas analyzers so that the predictive maintenance can be calculated.
Procedure
1. Fasten the PLC and COM module to the mounting rail.
2. Fasten the power supply to the mounting rail.
3. Fasten the SIMATIC HMI.
4. Connect your computer and SIMATIC HMI to the PLC via an Ethernet cable.
5. Connect the power supply for the PLC and SIMATIC HMI.
6. Connect the SIPROCESS GA700 to the PLC via an Ethernet cable.
In the case of several SIPROCESS GA700 gas analyzers, use a switch.
Analyzer Intelligence Director
Operating Instructions, 05/2022, A5E51328515-AA 11

7. Connect the CGA Series 6 and ULTRAMAT 23 to the COM module via a RS485 cable.
Follow the pin assignment:
11
53
8
84
QJO%TVCDPOOFDUPS
QJO%TVCDPOOFDUPS
1-$
34&-"/ 9.5
9.5
(/%
$("4FSJFT
6-53"."5
$.15134#"
Figure 3-1 Sub D socket connector
8. Follow the Technical data (Page 37).
You can order accessories (Page 39) online:
3.2 Con󹪝guring a new network
Requirement
You have connected your computer and all devices to the PLC.
Commissioning
3.2 Con󹪝guring a new network
Analyzer Intelligence Director
12 Operating Instructions, 05/2022, A5E51328515-AA

Procedure
1. Set the IP addresses of your computer so that each IP address only occurs once in the entire
network.
The default device addresses are:
SITRANS AID IQ devices IP address Subnet mask Master ELAN address
PLC 192.168.0.10 255.255.255.0 14
SIMATIC HMI 400 192.168.0.3 -
SIMATIC HMI 700 192.168.0.4 -
Your computer can, for example, have the IP address 192.168.0.4.
2. To set the device addresses of the gas analyzers, enter the IP address of the PLC in the
browser: https:\\192.168.0.10
3. In the main menu "Filebrowser" select the folder "Recipes".
4. Export the 󹪝le DB_ROM_RCP_DeviceIdent.csv.
5. Open the 󹪝le in Notepad.
CAUTION! Do not open the 󹪝le in other editors or Microsoft Excel.
6. Enter the IP addresses and ELAN addresses of the gas analyzers as shown in the following
example.

①IP address SIPROCESS GA700
②ELAN address CGA Series 6
Figure 3-2 Example for a DB_ROM_RCP_DeviceIdent.csv 󹪝le
7. Import the 󹪝le.
8. Activate the con󹪝guration via the PLC web client or SIMATIC HMI.
Commissioning
3.2 Con󹪝guring a new network
Analyzer Intelligence Director
Operating Instructions, 05/2022, A5E51328515-AA 13

3.3 Integrating SITRANS AID IQ into an existing network
Requirement
You have connected your computer and all devices to the PLC.
You know all IP addresses and the master ELAN address of the PLC.
Procedure
1. Set the IP addresses of your computer so that each IP address only occurs once in the entire
network.
The default device addresses are:
SITRANS AID IQ devices IP address Subnet mask Master ELAN address
PLC 192.168.0.10 255.255.255.0 14
SIMATIC HMI 400 192.168.0.3 -
SIMATIC HMI 700 192.168.0.4 -
Your computer can, for example, have the IP address 192.168.0.4.
2. To set the device addresses, enter the IP address of the PLC in the browser. For example https:\
\192.168.0.10.
3. Select the main menu "Filebrowser" and then the folder "Recipes".
4. Export the 󹪝le DB_ROM_RCP_DeviceIdent.csv.
5. Open the .csv 󹪝le in Notepad.
CAUTION! Do not open the 󹪝le in other editors or Microsoft Excel.
6. Enter the IP addresses and ELAN addresses of the gas analyzers as shown in the following
example.

①IP address SIPROCESS GA700
②ELAN address CGA Series 6
Figure 3-3 Example for a DB_ROM_RCP_DeviceIdent.csv 󹪝le
7. Import the 󹪝le.
Commissioning
3.3 Integrating SITRANS AID IQ into an existing network
Analyzer Intelligence Director
14 Operating Instructions, 05/2022, A5E51328515-AA

8. Export the 󹪝le DB_ROM_RCP_MasterCon󹪝g.csv.
9. Open the .csv 󹪝le in Notepad.
CAUTION! Do not open the 󹪝le in other editors or Microsoft Excel.
10.If required, enter a new PLC IP address and PLC master ELAN address as shown in the
following example.

①PLC IP address
②PLC master ELAN address
Figure 3-4 Example for a DB_ROM_RCP_MasterCon󹪝g.csv 󹪝le
11.Import the 󹪝le.
12.Activate the changed con󹪝guration with the PLC web client or SIMATIC HMI.
13.Change the SIMATIC HMI network settings.
Changing the SIMATIC HMI network settings (Page 15)
14.Activate the PLC IP address at the front panel of the PLC by setting the CPU to "STOP" and then
back to "RUN".
15.Couple the PLC and SIMATIC HMI again.
16.Start the SITRANS AID IQ web server with updated IP address.
Calling the SITRANS AID IQ web server (Page 25)
3.4 Changing the SIMATIC HMI network settings
Requirement
You have connected all devices.
Commissioning
3.4 Changing the SIMATIC HMI network settings
Analyzer Intelligence Director
Operating Instructions, 05/2022, A5E51328515-AA 15

Procedure
1. Restart the SIMATIC HMI.
2. During the restart switch to the con󹪝guration menu by clicking the "Settings" button in the
Start Center.
Desktop and Start Center (Page 16)
3. Adapt the IP address of the SIMATIC HMI to the network of the gas analyzers by opening
"Enter IP address and name server" in the Control Panel.
Entering the IP address and name server (Page 17)
4. Change the connection data for the PLC by opening "Edit IP addresses and communication
connections" in the Control Panel.
Editing IP addresses and communication connections (Page 19)
5. Start the SITRANS AID IQ in the Start Center with the button "Start".
Call up SITRANS AID IQ on the SIMATIC HMI (Page 27)
3.4.1 Desktop and Start Center
Once the HMI device has been started, the display shows the desktop.

①Desktop
②Start Center
③Start menu
④Icon for screen keyboard
Commissioning
3.4 Changing the SIMATIC HMI network settings
Analyzer Intelligence Director
16 Operating Instructions, 05/2022, A5E51328515-AA

The Start Center
The Start Center buttons have the following function:
• Transfer – You switch the HMI device to the "Transfer" operating mode.
The transfer mode is only activated if at least one data channel has been con󹪝gured.
• Start – You start the project on the HMI device.
If you do not perform an operation, a project already loaded on the HMI device will start
automatically in line with the settings in the Control Panel . If no project is loaded, the Start
Center will activate the transfer.
• Settings – You start the Control Panel.
• Taskbar – You open the task list and the Start menu.
The Start Center is displayed again if a project on the HMI device has been closed or if it is
accessed from the project.
3.4.2 Entering the IP address and name server
You can change the network settings for the LAN connection under "Network&Dial-
Up Connections". You can also con󹪝gure the properties of the Ethernet ports of the HMI
device.
Requirement
The Control Panel is open.
Procedure
Proceed as follows:
1. Open the network adapter display using the "Network&Dial-Up Connections" icon.
The image below shows the network adapter of a KP1500 Comfort.
The second network adapter "PN_X3" is present for the Comfort devices as of 15".
2. Open the "PN_X1" entry.
The 'PN_X1' Settings dialog opens.
3. Change to the "IP Address" tab.
4. Select the type of address assignment:
– To determine the address manually, select "Specify an IP address".
Commissioning
3.4 Changing the SIMATIC HMI network settings
Analyzer Intelligence Director
Operating Instructions, 05/2022, A5E51328515-AA 17

5. If you have selected manual address assignment, enter the corresponding addresses under
"IP Address", "Subnet Mask" and under "Default Gateway", if necessary.
Note
PROFINET I/O error if the PN_X1 and PN_X3 subnet masks are identical
In principle, the two network adapters may be assigned to a shared physical subnetwork.
If you have enabled PROFINET services for PN_X1 and the IP subnet masks of the two network
adapters are identical, PROFINET I/O errors may occur.
Assign a di󹪜erent entry for each network adapter in PROFINET I/O operation under "Subnet
Mask".
Note
You can also con󹪝gure the network address in the "Devices & Networks" editor in WinCC. You
can 󹪝nd more information on this topic in the WinCC online help.
6. If a name server is used in the network, change to the "Name Servers" tab.
7. Enter the corresponding addresses.
8. If you want to set additional Ethernet parameters, open the "Ethernet Parameters" tab.
The KP400 Comfort and KTP400 Comfort HMI devices only have one Ethernet interface
"Port1".
Commissioning
3.4 Changing the SIMATIC HMI network settings
Analyzer Intelligence Director
18 Operating Instructions, 05/2022, A5E51328515-AA

9. The transmission mode and the speed of the Ethernet ports are set automatically by default.
If needed, select the transmission mode and speed for the Ethernet port of the HMI device.
You can also set limits for the two Ethernet ports:
– "End of detection of accessible nodes": DCP frames for detecting accessible nodes are not
forwarded. Nodes located beyond this Ethernet port are no longer accessible.
– "End of topology discovery": LLDP frames for topology discovery are not forwarded.
Note
For the HMI devices KP400 Comfort and KTP400 Comfort, only the "End of topology
discovery" option is available.
10.Change the limits for the Ethernet ports "Port 1" and "Port 2", if needed.
The KP400 Comfort and KTP400 Comfort HMI devices only have one Ethernet interface
"Port1".
11.Con󹪝rm your entries with "OK".
The LAN connection parameters for the HMI device have been changed.
3.4.3 Editing IP addresses and communication connections
3.4.3.1 Overview
This section describes how you can, from your HMI device, change the IP addresses of controllers
and other HMI devices in the subnet of your HMI device and adapt the associated
communication connections accordingly. This gives you the ability to create a project, transfer
it to multiple HMI devices and then adapt the respective controller connections without
changing the project.
If you change the IP addresses of other devices in the subnet of your HMI device, the following
steps are required:
• Update IP address and device name; see section "Assigning IP address and device name
(Page 19)"
• Update communication connection; see section "Con󹪝guring a communication connection
(Page 22)".
The following functions are also available:
• A scan function to list the HMI devices and PLC in the subnet.
• Filter function for the scan results
• Check assignment of IP addresses and device names for HMI devices and PLCs.
• Project IP addresses and device names for HMI devices and PLCs can be restored.
3.4.3.2 Assigning IP address and device name
You can use the "Assign IP" function to edit the IP address and device name of target devices in
the subnet of your HMI device. The target device can be a controller or another HMI device.
Commissioning
3.4 Changing the SIMATIC HMI network settings
Analyzer Intelligence Director
Operating Instructions, 05/2022, A5E51328515-AA 19

Requirement
• The Control Panel is open.
• For HMI devices, the following applies: The project that runs on the target device is closed.
• For controllers, the following applies:
– The controller is of type S7-300, S7-400, S7-1200 or S7-1500.
– HMI access is allowed in the settings.
– The controller is in "STOP" state.
• Your system administrator has provided you with the necessary information.
Procedure
1. Open the "Service & Commissioning" dialog using the "Service & Commissioning" icon.
2. Change to the "IP Con󹪝g" tab.

①Button for changing IP address and device name
②Button for changing the con󹪝gured communication connections
Commissioning
3.4 Changing the SIMATIC HMI network settings
Analyzer Intelligence Director
20 Operating Instructions, 05/2022, A5E51328515-AA